title>SY/T 5002-1996 Connection dimensions of wearing parts of double-acting drilling pumps - SY/T 5002-1996 - Chinese standardNet - bzxz.net
Home > SY > SY/T 5002-1996 Connection dimensions of wearing parts of double-acting drilling pumps
SY/T 5002-1996 Connection dimensions of wearing parts of double-acting drilling pumps

Basic Information

Standard ID: SY/T 5002-1996

Standard Name: Connection dimensions of wearing parts of double-acting drilling pumps

Chinese Name: 双作用钻井泵易损件连接尺寸

Standard category:Oil and gas industry standards (SY)

state:in force

Date of Release1996-12-15

Date of Implementation:1997-06-30

standard classification number

associated standards

alternative situation:Replaces SY 5002-1980 SY 5003-1980 SY 5004-1980 SY 5005-1980 SY 5006-1980 SY 5007-1980 SY 5008-1980 SY 5009-1980 SY 5010-1980 SY 5011-1980 SY 5012-1980 SY 5013-1980 SY 5014-1980 SY 5015-1980 SY 5016-1980 SY 5017-1980 SY 5018-1980 SY 5019-1980

Publication information

other information

Introduction to standards:

SY/T 5002-1996 Connection dimensions of wearing parts of double-acting drilling pumpsSY/T5002-1996 Standard download decompression password: www.bzxz.net

Some standard content:

SY/T 5002--1996 Petroleum and Natural Gas Industry Standard of the People's Republic of China
Double-acting Drilling and Pump Wearing Parts Connection Dimensions
1996-1215 Issued
China National Petroleum Corporation
1997-06-30 Implementation
This standard is based on Section 2.5\Mud Pump Parts" of the American Petroleum Institute Standard API Spec 7K "Drilling Equipment Specification" (1994 Edition) and has revised SY5002~5019-80. According to the current domestic situation, when adopting Section 2.5 of API Spec 7K, the plug rod, intermediate rod, nut and lock nut are only connected by cone: cylindrical thread, and the cylindrical thread is deleted. Connection (inconvenient installation and disassembly). In the section "Piston rod and active core hole", the single-acting content (not belonging to the double-acting pump) was deleted. This standard will take effect from: At the same time replace SY5002~5019-80 This standard is proposed and managed by the Jinguo Petroleum Drilling Equipment and Tools Standardization Technical Committee. Drafting unit of this standard: Baoji Petroleum Machinery Factory. The main drafter of this standard Pu Rongchun
Petroleum and Natural Gas Industry Standard of the People's Republic of China Double-acting Drilling Pump Wearing Parts Connection Dimensions
SY/ T 50021996
Replaces sY5002-501980
This standard specifies the specifications and connection dimensions of the main wearing parts of double-acting drilling pumps (hereinafter referred to as drilling pumps). Its contents include: piston rod and piston core hole, piston rod, intermediate rod, crosshead and locking nut, valve chamber; piston, cylinder sleeve. This standard applies to the design, manufacture, ordering and use of the main wearing parts of double-acting drilling pumps. 2 Cited standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised: All parties using this standard should discuss the use of the following The possibility of listing the latest version of the standard. GB/T197-1981 General thread tolerance and fit (true diameter 13551111) GB/T1184-1980 Form and position tolerances Provisions for unmarked tolerances API Spec 7K (1994) Drilling equipment specification 3 Piston rod and piston core hole
3.1 Specifications and dimensions
The piston rod and piston core hole of the hydraulic end of the double-acting pump shall comply with the provisions of Figure 1, Figure 2 and Table ". Steaming surface N
Piston center line (hand tight)
Rubbing surface P
1 Taper K
R3 (if there is a step)
Reverse shuttle angle
Figure 1 1 to G taper
China National Petroleum Corporation approved on December 15, 1996 R2.5 or 2.5 × 45°
1997-06-30 implementation
Tainan M
SY/T5002-1996
Piston center line behind the piston
HP type piston
More taper K
R2.5 or 2.5 × 45°
Maximum extension length of the piston, E
The bottom of the piston should be strengthened by surface processing. 25HP and 6HP taper
3.2 Thread
The thread on the end of the piston rod and the thread on the nut shall conform to the dimensions listed in Table 1 and shall conform to the 6H/69 accuracy given in GB/T197. 3.3 Piston and rod shoulder
For 5HP and 6HP piston and rod shoulder surfaces M and N, they should be perpendicular to the cone axis, with a verticality of 0.025mm111The end surface P should also be perpendicular to the cone axis, with a verticality of 0.125mml3.4HP type piston installation instructions
a) Clean the cone surface of the piston rod and piston and assemble (no oil on the cone surface). b) When tightening the piston by hand, there must be a gap between the piston and the piston rod shoulder. c) Apply lubricating oil to the thread and nut end face to prevent scratches. d) The nut presses the piston to the piston rod shoulder. e) After the piston initially contacts the shoulder, punch or print stripes to mark the relative position between the nut and the piston, and then tighten the nut 60 to 72° (1 circle equals 360°). 3.5 Marking
3.5.1 Pistons whose taper conforms to this standard shall be marked with the manufacturer's name or mark and taper number. High-pressure pistons with taper numbers 5HP and 6HP are interchangeable with pistons with taper numbers 5 and 6 in terms of dimensions, and it is allowed to mark both taper numbers on the end face P. 3.5.2 Piston rods
Piston rods that conform to this standard shall be marked with the manufacturer's name or mark and taper number. The intermediate rod end of the piston rod shall be marked with the cone-cylindrical thread code listed in Table 2.
4 Plug rods, intermediate rods, crossheads and lock nuts 4.1 The cone-cylindrical threaded connection of piston rods, intermediate rods and crossheads shall conform to the provisions of Figure 3 and Table 2. 4.2 The thread profile, basic dimensions and tolerances shall conform to the provisions of API Spec 7K. 4.3 The spacing between internal and external threads shall conform to the provisions of API Spec 7K. 5002—1996
(vz-Nx +/, z)
(VZ-Nn8-\ /
(Vz-8-t /
(Vz-Nn8-* / L
B- ×5t
(Vz-N8-/
(V2-N8-1
R9-E st
LIE'69
219'9s
(6260)
/) ()(*, 6)
(t /eE)
(5 /,)
(8 e2)
ost'ts
(oost)
(oon t)
(8/8)
(*/16)
(9/s 8)
(8)
(°/ 2)
(8 / s)
(3/,t ~E)
(/, E~t/+z)
( /~t /, 2)
(2 / 2 ~3/, 1)
(c /s~/ )
(t /t ~)
SY/T 5002-996
4.4 The verticality of the internal thread end face to the axis shall meet the tolerance grade 7 specified in GB/T1184. The thread axis shall coincide with the piston rod design line within the limit that can be achieved in good operation. The parallelism of the thread axis and the piston rod design axis shall meet the tolerance grade 6.
2SminX45
Crosshead
2. 5min× 455
Locking nut,
Figure 3 Cone-cylindrical threaded joints for piston rods, intermediate rods and crossheads Table 2 Cone-cylindrical threaded joints for piston rods, intermediate rods and crossheads 2
Chain thread code
Nominal size A
25.400(1)
28.575(1 // 8)
31.750(1 1/4)
34,925(1 7 / g)
38.100(1 1 / 2)
41.275(1 5 / 8)
44.450(1/4)
47.625(17/)
50.800(2)
57.150(2 1 / 4)
63.500(2 7)
69.850(2/4)
76.200(3)
82.550(3' / )
88.900(3' / 2)
101.600(4)
114.300(4 1/ 2)
127.000(5)
139.700(5/ 2)
152.400(6)
Conical thread length B
31.8(1 / g)
35.7(1 13 / 32)
39.7(1 /1)
43.7(1 2* / 2)
47.G(1 7 / g)
51.6(2 */ 2)
55.6(2 3 / e)
59.5(2 \/ 32)
63.5(2 1 / 2)
71.4(2 13 / 15)
79.4(3 1/ 8)
87.3(3 7/ 16)
95.3(3 * / 4)
103.2(4 // 16)
111.1(4 3 / n)
142.9(5 5 / s)
158.8(6 1/ 4)
174.6(G 7 / g)
190.5(7 17 2)
Cylindrical thread length
31.8(1 ±/ 4)
31.8(1 */4)
31.8(1 1/ g)
31.8(1 / 4)
38.1(1 1/ 2)
44.5(1 3 / )
44.5(1*/ a)
57.2(2 */4)
57.2(2 / )
28.6(1 1 / )
28.6() 1/ g)
31.8(1 : / 4)
34.9(1 1/)
38.1(1 1/ 2)
41.3(15/)
44.5(1 3/ )
47,617/)
5 Valve Chamber
5.1 Specifications and Dimensions
SY/T 50021996
The valve chamber of the drilling pump shall be supplied in accordance with the specifications and dimensions specified in the user's order and in accordance with the specifications and dimensions listed in Table 3 and Figure 4. For valves with guide parts, the valve chamber shall have the minimum dimension G (see Figure 4 and Table 3). 5.2 Spring Installation Dimensions
The spring installation dimensions in the valve chamber shall comply with the dimensions L, M and N shown in Figure 4 and Table 3. 5.3 Marking
Drilling pump valve chambers supplied in accordance with this standard shall be marked with the manufacturer's name or mark and the specification number of the valve chamber. The mark shall be cast or printed on the cylinder, or the label shall be firmly fixed on the cylinder, and the label shall be fixed in a place where it can be seen after the cylinder is installed. If the hydraulic force is composed of several cylinders, each cylinder should be marked with force
Minimum distance
Figure 4 Drilling pump valve chamber
(3 2 / g)
Valve chamber size
(1/)
(3 1 / 4)
(4 // 4)
(4 -/ 4)
(13 / 16)
13 / 16)
13/ 16
Drilling pump valve chamber
(2 1/ 4)
(2 1 / 2)
(2 ~/ 4)
(31/4)
(4 1 / g)
(2 5 / k)
(2 - / 4)
Spring installation size
(2 1/ )
(13/4)
(2 /2)
(3/72)
(5 */ )
(3 5/ )
(61 /)
(7 7/)
(9 1/ 2)
* is the trial size
6 piston
(1 1/2)
(2 1/ 4)
(2 1 / )
(3 (/ 4) | |tt | g)
(15/1)
(15/6)
(1 5/ )
(15/6)
(15/ 16)
(1 5/)
(15/ 1)
(3 5/ 4)
(3 1/ 4)
(32/ 4)
(4 t/)
(4 1/ 2)
(4 7 / g)
(5 / 4)
(5 1/)
(s 5/ a)
(6 */)
(7 1/)
(3 °/ g)
(3 ° / 8)
(4 °/ s)
(5 / )
Spring installation size
(2 / )
(2 ~/)
(3 /4)
(33/4)
(3 1/)
(2 / 4)
(2 / )
(27/4)
(3 /4)
(3 // 4)
(4 / )
(4 1/2)
(4 /4)
(5 / 4)
(5 /4)
The bore of the drilling pump piston shall be machined into a tapered bore that matches the standard piston rod taper shown in Figure 1 and Table 1: The piston outer diameter shall be suitable for working in a cylinder liner with an inner diameter as shown in Figure 5. 6.2 Marking
Pistons that comply with this standard shall be marked with the manufacturer's name or mark, the corresponding taper number and the nominal diameter. The mark shall be printed in steel letters 3.5mm high on the end face P of the piston core (see Figures 1 and 2). 7 Cylinder liner
7.1 Cylinder liner inner diameter
The inner diameter of the drilling pump cylinder liner shall be given in 10mm steps. The tolerance is shown in Figure 5.7.2 Chamfer
The inner diameter of the cylinder liner can be manufactured according to other step series specified in the user's order. SY/T 50021996
The inner edge of the piston end of the drilling pump cylinder liner shall be chamfered as shown in Figure 5. 7.3 Marking
The cylinder liner that complies with this standard shall be marked with the manufacturer's name or mark and the cylinder liner specification (standard inner diameter). The mark shall be printed on the end face (outer end) of the cylinder liner in steel letters 3.511m high10
A-Nominal diameter
Figure 5 Drilling pump cylinder liner1 Specifications and dimensions
SY/T 50021996
Drilling pump valve chambers shall be supplied in accordance with the specifications and dimensions specified in the user's order and in accordance with the specifications and dimensions listed in Table 3 and Figure 4. For valves with guide parts, the valve chamber shall have the minimum dimension G (see Figure 4 and Table 3). 5.2 Spring installation dimensions
The spring installation dimensions in the valve chamber shall comply with the dimensions L, M and N shown in Figure 4 and Table 3. 5.3 Marking
Drilling pump valve chambers supplied in accordance with this standard shall be marked with the manufacturer's name or mark and the specification number of the valve chamber. The marking shall be cast or printed on the cylinder, or a label shall be firmly fixed on the cylinder, and the label shall be fixed in a place where it can be seen after the cylinder is installed. If the hydraulic force is composed of several cylinders, each cylinder should be marked with force
Minimum distance
Figure 4 Drilling pump valve chamber
(3 2 / g)
Valve chamber size
(1/)
(3 1 / 4)
(4 // 4)
(4 -/ 4)
(13 / 16)
13 / 16)
13/ 16
Drilling pump valve chamber
(2 1/ 4)
(2 1 / 2)
(2 ~/ 4)
(31/4)
(4 1 / g)
(2 5 / k)
(2 - / 4)
Spring installation size
(2 1/ )
(13/4)
(2 /2)
(3/72)
(5 */ )
(3 5/ )
(61 /)
(7 7/)
(9 1/ 2)
* is the trial size
6 piston
(1 1/2)
(2 1/ 4)
(2 1 / )
(3 (/ 4) | |tt | g)
(15/1)
(15/6)
(1 5/ )
(15/6)
(15/ 16)
(1 5/)
(15/ 1)
(3 5/ 4)
(3 1/ 4)
(32/ 4)
(4 t/)
(4 1/ 2)
(4 7 / g)
(5 / 4)
(5 1/)
(s 5/ a)
(6 */)
(7 1/)
(3 °/ g)
(3 ° / 8)
(4 °/ s)
(5 / )
Spring installation size
(2 / )
(2 ~/)
(3 /4)
(33/4)
(3 1/)
(2 / 4)
(2 / )
(27/4)
(3 /4)
(3 // 4)
(4 / )
(4 1/2)
(4 /4)
(5 / 4)
(5 /4)
The bore of the drilling pump piston shall be machined into a tapered bore that matches the standard piston rod taper shown in Figure 1 and Table 1: The piston outer diameter shall be suitable for working in a cylinder liner with an inner diameter as shown in Figure 5. 6.2 Marking
Pistons that comply with this standard shall be marked with the manufacturer's name or mark, the corresponding taper number and the nominal diameter. The mark shall be printed in steel letters 3.5mm high on the end face P of the piston core (see Figures 1 and 2). 7 Cylinder liner
7.1 Cylinder liner inner diameter
The inner diameter of the drilling pump cylinder liner shall be given in 10mm steps. The tolerance is shown in Figure 5.7.2 Chamfer
The inner diameter of the cylinder liner can be manufactured according to other step series specified in the user's order. SY/T 50021996
The inner edge of the piston end of the drilling pump cylinder liner shall be chamfered as shown in Figure 5. 7.3 Marking
The cylinder liner that complies with this standard shall be marked with the manufacturer's name or mark and the cylinder liner specification (standard inner diameter). The mark shall be printed on the end face (outer end) of the cylinder liner in steel letters 3.511m high10
A-Nominal diameter
Figure 5 Drilling pump cylinder liner1 Specifications and dimensions
SY/T 50021996
Drilling pump valve chambers shall be supplied in accordance with the specifications and dimensions specified in the user's order and in accordance with the specifications and dimensions listed in Table 3 and Figure 4. For valves with guide parts, the valve chamber shall have the minimum dimension G (see Figure 4 and Table 3). 5.2 Spring installation dimensions
The spring installation dimensions in the valve chamber shall comply with the dimensions L, M and N shown in Figure 4 and Table 3. 5.3 Marking
Drilling pump valve chambers supplied in accordance with this standard shall be marked with the manufacturer's name or mark and the specification number of the valve chamber. The marking shall be cast or printed on the cylinder, or a label shall be firmly fixed on the cylinder, and the label shall be fixed in a place where it can be seen after the cylinder is installed. If the hydraulic force is composed of several cylinders, each cylinder should be marked with force
Minimum distance
Figure 4 Drilling pump valve chamber
(3 2 / g)
Valve chamber size
(1/)
(3 1 / 4)
(4 // 4)
(4 -/ 4)
(13 / 16)
13 / 16)
13/ 16
Drilling pump valve chamber
(2 1/ 4)
(2 1 / 2)
(2 ~/ 4)
(31/4)
(4 1 / g)
(2 5 / k)
(2 - / 4)
Spring installation size
(2 1/ )
(13/4)
(2 /2)
(3/72)
(5 */ )
(3 5/ )
(61 /)
(7 7/)
(9 1/ 2)
* is the trial size
6 piston
(1 1/2)
(2 1/ 4)
(2 1 / )
(3 (/ 4) | |tt | g)
(15/1)
(15/6)
(1 5/ )
(15/6)
(15/ 16)
(1 5/)
(15/ 1)
(3 5/ 4)
(3 1/ 4)
(32/ 4)
(4 t/)
(4 1/ 2)
(4 7 / g)
(5 / 4)
(5 1/)
(s 5/ a)
(6 */)
(7 1/)
(3 °/ g)
(3 ° / 8)
(4 °/ s)
(5 / )
Spring installation size
(2 / )
(2 ~/)
(3 /4)
(33/4)
(3 1/)
(2 / 4)
(2 / )
(27/4)
(3 /4)
(3 // 4)
(4 / )
(4 1/2)
(4 /4)
(5 / 4)
(5 /4)
The bore of the drilling pump piston shall be machined into a tapered bore that matches the standard piston rod taper shown in Figure 1 and Table 1: The piston outer diameter shall be suitable for working in a cylinder liner with an inner diameter as shown in Figure 5. 6.2 Marking
Pistons that comply with this standard shall be marked with the manufacturer's name or mark, the corresponding taper number and the nominal diameter. The mark shall be printed in steel letters 3.5mm high on the end face P of the piston core (see Figures 1 and 2). 7 Cylinder liner
7.1 Cylinder liner inner diameter
The inner diameter of the drilling pump cylinder liner shall be given in 10mm steps. The tolerance is shown in Figure 5.7.2 Chamfer
The inner diameter of the cylinder liner can be manufactured according to other step series specified in the user's order. SY/T 50021996
The inner edge of the piston end of the drilling pump cylinder liner shall be chamfered as shown in Figure 5. 7.3 Marking
The cylinder liner that complies with this standard shall be marked with the manufacturer's name or mark and the cylinder liner specification (standard inner diameter). The mark shall be printed on the end face (outer end) of the cylinder liner in steel letters 3.511m high10
A-Nominal diameter
Figure 5 Drilling pump cylinder liner1 Specifications and dimensions
SY/T50021996
Table 3 (End)
Valve cavity size
(5 5/a)
(5 /4)
(7 3/ )
(81/g)
(9 1/ g)
(15/1)
(15/6)
(1 5/ )
(15/6)
(15/ 16)
(1 5/)bZxz.net
(15/ 1)
(3 5/ 4)
(3 1/ 4)
(32/ 4)
(4 t/)
(4 1/ 2)
(4 7 / g)
(5 / 4)
(5 1/)
(s 5/ a)
(6 */)
(7 1/)
(3 °/ g)
(3 ° / 8)
(4 °/ s)
(5 / )
Spring installation size
(2 / )
(2 ~/)
(3 /4)
(33/4)
(3 1/)
(2 / 4)
(2 / )
(27/4)
(3 /4)
(3 // 4)
(4 / )
(4 1/2)
(4 /4)
(5 / 4)
(5 /4)
The bore of the drilling pump piston shall be machined into a tapered bore that matches the standard piston rod taper shown in Figure 1 and Table 1: The piston outer diameter shall be suitable for working in a cylinder liner with an inner diameter as shown in Figure 5. 6.2 Marking
Pistons that comply with this standard shall be marked with the manufacturer's name or mark, the corresponding taper number and the nominal diameter. The mark shall be printed in steel letters 3.5mm high on the end face P of the piston core (see Figures 1 and 2). 7 Cylinder liner
7.1 Cylinder liner inner diameter
The inner diameter of the drilling pump cylinder liner shall be given in 10mm steps. The tolerance is shown in Figure 5.7.2 Chamfer
The inner diameter of the cylinder liner can be manufactured according to other step series specified in the user's order. SY/T 50021996
The inner edge of the piston end of the drilling pump cylinder liner shall be chamfered as shown in Figure 5. 7.3 Marking
The cylinder liner that complies with this standard shall be marked with the manufacturer's name or mark and the cylinder liner specification (standard inner diameter). The mark shall be printed on the end face (outer end) of the cylinder liner in steel letters 3.511m high10
A-Nominal diameter
Figure 5 Drilling pump cylinder liner1 Specifications and dimensions
SY/T50021996
Table 3 (End)
Valve cavity size
(5 5/a)
(5 /4)
(7 3/ )
(81/g)
(9 1/ g)
(15/1)
(15/6)
(1 5/ )
(15/6)
(15/ 16)
(1 5/)
(15/ 1)
(3 5/ 4)
(3 1/ 4)
(32/ 4)
(4 t/)
(4 1/ 2)
(4 7 / g)
(5 / 4)
(5 1/)
(s 5/ a)
(6 */)
(7 1/)
(3 °/ g)
(3 ° / 8)
(4 °/ s)
(5 / )
Spring installation size
(2 / )
(2 ~/)
(3 /4)
(33/4)
(3 1/)
(2 / 4)
(2 / )
(27/4)
(3 /4)
(3 // 4)
(4 / )
(4 1/2)
(4 /4)
(5 / 4)
(5 /4)
The bore of the drilling pump piston shall be machined into a tapered bore that matches the standard piston rod taper shown in Figure 1 and Table 1: The piston outer diameter shall be suitable for working in a cylinder liner with an inner diameter as shown in Figure 5. 6.2 Marking
Pistons that comply with this standard shall be marked with the manufacturer's name or mark, the corresponding taper number and the nominal diameter. The mark shall be printed in steel letters 3.5mm high on the end face P of the piston core (see Figures 1 and 2). 7 Cylinder liner
7.1 Cylinder liner inner diameter
The inner diameter of the drilling pump cylinder liner shall be given in 10mm steps. The tolerance is shown in Figure 5.7.2 Chamfer
The inner diameter of the cylinder liner can be manufactured according to other step series specified in the user's order. SY/T 50021996
The inner edge of the piston end of the drilling pump cylinder liner shall be chamfered as shown in Figure 5. 7.3 Marking
The cylinder liner that complies with this standard shall be marked with the manufacturer's name or mark and the cylinder liner specification (standard inner diameter). The mark shall be printed on the end face (outer end) of the cylinder liner in steel letters 3.511m high10
A-Nominal diameter
Figure 5 Drilling pump cylinder liner
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.