Standard ICS number:Agriculture>>Agricultural buildings, structures and installations>>65.040.20 Buildings and installations for processing and storing agricultural products
Standard Classification Number:Agriculture, Forestry>>Agricultural and Forestry Machinery and Equipment>>B92 Livestock and Poultry Machinery and Equipment
associated standards
Procurement status:eqv ISO 5710:1980
Publication information
other information
Focal point unit:Hohhot Animal Husbandry Machinery Research Institute
Publishing department:Hohhot Animal Husbandry Machinery Research Institute
JB/T 10131-1999 This standard is equivalent to ISO 5710:1980 "Manure scraper conveyor for stables in feedlots", and the original standard has been re-edited in accordance with the provisions of my country's standard compilation. This standard specifies the technical requirements and safety requirements for closed chain continuous manure scraper conveyors. This standard applies to devices that use the continuous movement of scrapers to move collected solid and liquid manure in closed livestock houses. This standard is published for the first time. JB/T 10131-1999 Manure scraper conveyor for stables in feedlots JB/T10131-1999 Standard download decompression password: www.bzxz.net
Some standard content:
JCS 65.040.10 Machinery Industry Standard of the People's Republic of China JB/T 10131—1999 eqyIo571019a0 Equipment for internal farm work and hushandryContinuous manure scraper conveyors for stalls1999.08-06 Issued State Machinery Industry Bureau 2000-01-01 Implementation JB/T4131-1999 This standard is equivalent to 55710:1980 Equipment for Farms Standards. In order to avoid misunderstanding, this standard was proposed and translated by Hohhot Animal Husbandry Machinery Research Institute when it was issued. This standard was drafted by Hohhot Animal Husbandry Machinery Research Institute. The main drafter of this standard is Yang Taijun. Sleeping manure scraper conveyor, for some unclear regulations in the standard JB/T 1D131-1999 1S (International Organization for Standardization) is a joint organization of national standard groups (member units) around the world. The formulation of international standards is completed by 1S0 technical committees. All member units can form technical committees and propose projects on behalf of the committees. Government departments and non-governmental organizations can contact 150 committees for consideration. The international standard draft adopted by the main technical committee must be voted by the member units before it is recognized as an international standard by the 150 committee. The standard 1505710 is formulated by the [S0/TC23 Agricultural and Forestry Tractors and Machinery Technical Committee. The voting members are: Australia, Ireland, Belgium, Bulgaria, |tt||Czech Republic Italy Libya Romania Spain Turkey The following countries voted against the proposal on technical grounds: Finland 1 Scope Machinery Industry Standard of the People's Republic of China Feeding Farm Equipment Meat Scraper Conveyor for Stalls Eqeipmcut for intermal farp work and husbandryContinuous manerc seraper couveyors for stallsThis standard specifies the technical and safety requirements for closed-loop continuous manure scraper conveyors. JB10131-1999 eQIS05710:1980Www.bzxZ.net This standard applies to equipment for moving solid and rolling fertilizer collected by continuous motion of a plate in the test environment. 2 Referenced standards The following standards contain provisions that constitute provisions of this standard by reference in the respective standards. When this standard is revised, the versions shown are valid. All standards are subject to revision. Parties using this standard should consider the possibility of using the latest versions of the following standards. JB.T7865—1995: Requirements for the reduction of operating instructions and technical documents for agricultural and forestry tractors and implements 3 Definitions This standard adopts the following definitions. 3.1 Driving device Driving gear chain drive. 3.2 Driving gear chain The movable coupling for mounting the scraper. 3.3 Koraper A device for directly piercing the manure. 3.4 Quide A device for changing the direction of motion of the drag chain. 1.5 Tightener A device for tightening the inner chain of the drag chain. 3.6 Cleaner A device for cleaning the scraper. 3. Lippin device A device for discharging manure at the discharging end: non-contact Technical requirements 4. [General requirements 4.1. ! Calibration equipment 7 working conditions Select the power of the motor and the drag gear cylinder. Approved by the State Machinery Industry Bureau on August 6, 1999 2000-01-01 Implementation BF10131-1999 4.1.2 The speed of the drag tooth chain shall not exceed 10mmin4.1.3 The scraper can be fixed to the drag tooth chain by bolts, other methods. The fixed part of the scraper shall be firmly fixed under any conditions.4.1.4 The guide groove used for the combination of the drag tooth chain and the scraper shall not have protrusions that hinder the scraper from conveying.4.1.5 If the elevator is used, drainage facilities shall be provided at the lowest point or special part of the elevator. 4.1.6 All lubrication and cleaning parts should be easily accessible for maintenance. The tension of the dragging teeth can be easily adjusted on the ground. 4.2 Dimensions A.2.1 Each scraper should be equally spaced from each other. The maximum spacing of the scrapers is 750mm. 4.2.2 The total width of the scraper and the dragging teeth is 360+lgmm, 410*mm, 460+mm or 5G*mm. The corresponding guide width is 400, 450, 50u or 600mm, and the lateral distance is 30-40mm. 4.1.3 The height of the scraper is 40-60mm. 4.2.4 When conveying solid manure, if the guide is covered or penetrated, there should be at least 300m2 of direct space on the cleaning circuit above the scraper. 4.3 Safety requirements 4.3.1 Electrical equipment should comply with the relevant national standards. 4.3.2 The conveyor should be equipped with an overload safety device to prevent the equipment from collapsing. 4.3.3 There should be an inclined belt support to ensure that during reverse conveying, materials will not fall back and endanger people or others. When raising or adjusting the false unloading device, the operator is not allowed to stand under it. 4.3.4 The guide parts of the drag chain should be equipped with an anti-expansion device to prevent people from being exposed to the outside. 4.3.5 The belts and chains on the motor and the connecting machine should have protective covers. 4.3.6 The cut surface of the conveyor should be smooth and should not have sharp edges and protruding parts that may cause harm. 4.3.7 The anti-corrosion treatment of the materials used for the conveyor should not have residual toxicity. 5 When delivering the goods, the supplier should provide the user of the conveyor with an instruction manual, which should comply with Section B 856.2 Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.