Some standard content:
IC537.040.20
G80,GB1
Chemical Industry Standard of the People's Republic of China
IIG/T 3008~-3010—1999
HG/T3635--3641—1999wwW.bzxz.Net
Photosensitive materials and test methods
1999-06-16 Issued
2000 06-01 Implementation
Issued by the State Administration of Petroleum and Chemical Industry
Preparation number: 3740\.999
IG/T3638—1999
This standard is equivalent to the international standard 1507247:1SS3 Photography-Film size-Document copy film size 3. According to relevant information of our country, this standard is formulated for the first time in my country: Appendix A and Appendix B of the standard are the appendixes of the standard. Appendix A and Appendix B are the appendixes of the standard. This standard is issued by the former Ministry of Chemical Industry of the People's Republic of China. The drafting of this standard is China Leji Film Co., Ltd. The beneficiaries of this standard are: Guangxu. ISO Foreword ISO (International Organization for Standardization) defines the national standardization bodiesIt is stipulated that the temperature (23\2) and the book rate change (5=5) of the air conditioner should be kept constant. 5. 1. 1 Recommended specifications 1) All the measurements should be reported as follows: if the relative humidity is determined by 1K, the nominal size of the recommended film specifications should be in accordance with the provisions of Table 1. Table 1 lists the \A\ specifications derived from the writing paper specified in GB/T148, which will be more widely adopted. \4 "More than ten" series see Appendix A,
Table 1 Recommended specifications for loose leaf film
11-3×.21
29.7× 42
[46. UX 2U8.U
20B.0996.u
25h.2x11k,u
418.2XE92.0
5H2. 3XK, 5
838.5×1166.6
Recommended: The target size when manufacturing film is the size that can be judged under the library. The recommended cutting and deviation rules
The recommended specifications for loose leaf film shown in Table 1 and the cutting and deviation rules for loose leaf film are given in Table 1. Table 2 Recommended film specifications for cutting and length standard values
Monthly
Note: This heat recognizes the target size of the film: a few pages smaller than the nominal specifications of the company. 5.1.3 Approved specifications
The nominal and daily size of loose-leaf films are temporarily recognized as meeting the requirements of Table 3, and the image benefit values are in accordance with the regulations of Table 3. Approved specifications of teaching film
20.3×25. 4
21.6X97.9
26.4x.30.5
30. EX4E. 7
.X43.?
45.6X54.E
E
201.6x252.8
215.1x278. 6
252.3X303.2
273- S X354. 2
351.3X431.c
40: 6:517.2
07.2×608.8
EQS.XYn..2
Note: These standard specifications are originally U.S. inches. Therefore, the Japanese standard size does not follow the specifications of the agricultural company. For details on the original size and the size of the meter, please see the attached material. In any case, the equipment manufacturer is encouraged to manufacture the equipment according to the specifications listed in Table 1. 5.2 The vertical length of the card is checked for vertical length, edge length, shape and size. It is also completed by comparing two separate commercially available rectangles of any one sheet. The size of the plate is the smallest size difference of the specification, and the other is made according to the size difference of the specification. The user of this number should not have any point falling within the small rectangle or any point falling outside the larger rectangle. 6 Roll of film
Total width of film
6.1.1 Recommended width
HG/I3638—1999
The standard and standard dimensions of the recommended width of roll of film shall comply with the provisions of Table 4. The "A-allowance" series is shown in Appendix A.
Table 4 Recommended width of roll of film
21 (for A5 and A1)
29.7 (for A4 and 3)
42 (for A2 and A2)
84.1 (for A1 and A0)
6.1.2 Longitudinal and differential rules for recommended width
The longitudinal and differential rules for the commercial film widths listed in Table 4 and the new metric widths are given in Table 5. 5 Recommended Specifications for Coil Width and Cutting and Storage Rules Nominal False N
and Marking Position
Note: The average size of the approved plastic and the size of the paper is slightly smaller than the average size of the paper. 6.1.3 Approved Width Rate
Investment Limit
Difference Simple Film Temporarily Accepted Specification Width as the nominal size, the standard size and its fall, the form 6 provisions. Table 6 Recommended Film Gram
Name
Exhibition De Guang
Note: These standards are also more than the original estimate! Therefore, the Japanese standard and the deviation are not in accordance with the specifications of Table 5. The details of the US ten-inch style and the current specification are shown in Appendix B.
No matter what, the equipment manufacturer will only manufacture equipment according to the different widths in Table 4 in the future. 6.2 The length of the old simple amine film should be
The standard length of the commercial cavity film is
: 3m, 2um, 3Um, 6um, S: h, 100am, = 75ra, 240r 350m. This length does not include the length of the light-proof lead film or the trailing film that is easy to splice and the length added by the film loading and unloading. The actual length of the cut ratio should be no less than the nominal length. 6.3 Joints
All commercial films are not allowed to be spliced
6. 4 Core
6.1.1 Length extension
Daily length of core is subject to the monthly width of rubber minus tmm·limited deviation+1 6.4.2 Inner diameter of standard
Recommended total inner diameter of core is (71.2±3.4mm, 51
When the inner diameter of the core is -9 mm
6.5 Cable winding
HG/T36381999
Best lifting The method is to wrap the film back around the film! The film (the beginning and the end are not fixed on the core. For the film industry, the film is condensed on the core, so that the film is in a symmetrical position on the film. The core should not go in at one end and come out from the other side. The actual film width, including any deviation from the winding and the core protruding from the film, should not exceed the maximum film cutting width of 1rm.
7 Packaging mark
7. 1. In order to ensure the correct use of the product, the packaging should be marked with sufficient identification marks: a) product name and specifications; b) other use conditions (such as safety lights); and c) input and output and hazard warning labels. Any packaging of a given level must be marked with the following items to achieve the desired effect: "Product name mark or trade name mark"; and c) manufacturer's name. Name or trademark address
Product catalog identification code of the manufacturer:
Bar code information:
Recycling period Packaging information:
Quantity of the unit contained in the package!
Nominal specifications are nominal filling and length. In document units. Table depth, smaller size first; batch number and/or original shaft number,
Expiration date or shelf life or storage control code; manufacturer recommended storage safety strips ",
Manufacturer recommended storage conditions*,
If necessary, give the priority to the mountain porcelain tips \; product quality will be certified \
five internal parts, locks and sales of products and the implementation of the standard 7.2 compliance
if the product needs to read the standard compliance with the rotten recommended to use the following time, \HG/3638-1999 \
long notice and case material planning book material benefits, future promotion fee selection and thank the difference F Ni (71.9 soil) m, 2) also need to mark the national security edge half to be determined in the package of other materials. 3) in the recommended safety case cattle (except Black", the mark of the single package should be identified,) this trade material can use the fixed word or tea code Beijing analysis, 5) this period I have been determined according to the standard 2
IG/T36381999
Appendix A
(Standard time record
Loose-leaf cavity film and poison cavity film\one-person margin\series "A-number" specifications and width store series are a variety of printing positioning marks and operation symbols with data for edge exchange margin, or printing two documents on the same sheet of film. 41 loose-leaf film
Loose-leaf film\A dozen domain\rules should comply with Table A. Regulations. Table A1: Standard value of film 4-plus, current format
33x26
38×123
The width of the film 4-plus is given in the table? The width of the film 1-plus is given in the table, which should comply with the provisions of Table 42. Table A2: Standard value of commercial film A-plus
The width of commercial film A-plus is given in Table 5, nominal value
178-0 >238.
XX,ux328.c
328.0 2:458.c
638.0X877.5
87731 27.F
153- 3
B1 General page cavity film approval specifications
HG/T36381999
【Standard Appendix】
The nominal and standard sizes and their deviations of the temporary approval specifications of the film (originally in inches) originally in inches shall comply with the provisions of Table: The table
contains the film approval title, the nominal values are originally in inches
11×12
11×14
12×15
14 >: 17
20×24
23.3×5. 4
21.6×27.9
25. 2X35. 5
30.5X15.7
35. 6:413-2
.xbu,x
Approved width of film
Monthly standard
7.94X6.55
8. 4712 97
10. 9× :, 47
11- 9X:7.7
13,H?X1F,97
-5.a7X15.67
H. ?N 23. 5?
, 07× 29. 97
2ul.x2.2-x
2.2.&X313.
272.#154.8
314.GX256.
3=4.8X431.3
405. 6 307. 3
3r.2..6ne.3
SCSgx761.2
The nominal daily standard dimensions and their deviations of the temporary approved distance, originally in inches, shall conform to the specifications in Table 1. Table 12 lists the approved widths of the road sheet, originally in inches. The nominal position
313- 5
EIG/T3638：1999
[Appendix to request)
Dimensional stability
The dimensions and deviations specified in this standard apply to the manufacture of butyl rubber sheets. The standard atmospheric conditions specified in ISO554 are as follows: temperature (23±2) and relative humidity (50±10). After equilibrium, these dimensions may change. For example, the film will shrink permanently due to aging, or shrink or shrink with the change of atmospheric humidity and density. Nevertheless, within the warranty period of the film and when the package is opened, the dimensional deviation of the film should not exceed 0.% to 3.11% of the cellulose ester film base film when measured under the standard atmospheric conditions of temperature (23±2) and relative humidity (50±5) during the film's manufacturing period. Polyester film 0.02%--0.1%, polyester film (0.05mm film 1 0. 02%: --
knock-off film
HG/T3638-1999
(Appendix of the suggestion)
Packing capacity
Recommended film single package or multi-piece package The film quantity of each unit can be selected from the following figures: 10 sheets. 25 sheets, 50 sheets 10u sheets, 150 sheets. 33 sheets. D2
Differential film
The packaging number of roll film is not recommended.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.