JB/T 6102.1-1999 JB/T 6102.1-1999 Accuracy of combined punching and shearing machine JB/T6102.1-1999 Standard download and decompression password: www.bzxz.net

ICS 25.120.10
J62
JB
Machinery Industry Standard of the People's Republic of China
JB/T6102.1-1999
Combined Punching and Shearing Machine|| tt||Released on 1999-05-14
National Machinery Industry Bureau
Accuracy
Implemented on 2000-01-01
Released
JB/T6102. 1-1999
Foreword
This standard is a revision of JB/T8085-95 "Accuracy of Combined Punching and Shearing Machines". The technical content of this standard is basically consistent with JB/T8085-95, and has only been re-edited in accordance with relevant regulations. This standard will be implemented from January 1, 2000. This standard replaces JB/T808595 from the date of implementation. This standard is proposed and administered by the National Forging Machinery Standardization Technical Committee. The unit responsible for drafting this standard: Heilongjiang Forging Machine Tool Factory. This standard was first published in October 1984. Scope
Mechanical Industry Standard of the People's Republic of China
Accuracy of Combined Punching and Shearing Machines
This standard specifies the geometric accuracy, working accuracy and inspection methods of combined punching and shearing machines. This standard applies to combined punching and shearing machines (hereinafter referred to as punching and shearing machines). 2 General requirements wwW.bzxz.Net
2.1 The requirements for accuracy inspection of punching and shearing machines should comply with the relevant regulations on accuracy inspection of forging presses. JB/T6102.1-1999 | | tt | mm is calculated as 0.01mm.
2.3 The accuracy inspection sequence of this standard does not represent the actual inspection sequence. For the convenience of assembly and disassembly of inspection tools and inspection, inspection can be carried out in any order.
3 Accuracy inspection items of punching and shearing machines
3.1 Leveling
Serial number
GO
Simplified
Picture
The State Machinery Industry Bureau approved the inspection item
Punching and shearing machine
leveling on 1999-05-14:
a. Longitudinal
b. Horizontal
Tolerance
mm
in 1000
length is
0.20
Inspection Tools
Level
Inspection ruler
Inspection method
Put a level ruler on the
work surface of the fuselage
,
Put a piece of water on it
, respectively
Inspection in the vertical and horizontal
directions
Implemented on 2000-01-01
JB/T6102.11999
refers to ||tt| |Put
Check
Dang
Dangdang
06
(?
·
001||tt ||Wen Yimei
中
在
E
Poor
allow
calculate the vertical number
Picture
简
0
*
2
JB/T 6102.11999
ruler
“
Jia | | tt | ||(?violent
)
01
u
shame
yun
车草湐
自| |tt||vL
Picture
Simplified
8
JB/T 6102.11999
Inspection
Exactly correct Device
Worker
Monkey
0
00
1
000000
0
Not constant Install
·oto
0001
grass
o
w
difference
allow
More fragrant than the face
35
Picture
Jian
0
8
JB/T 6102.11999
+1 %00[×
"06 and
this outfit
block
work
%
ota1f
allow| |tt||circle
简
JB/T6102.1-1999
b
4%001×-pp
法||tt| |Inspection
Inspection
%s1
Permission
Change
一
一
图
simple
d
id
of
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.