JB/T 8343.2-1999 JB/T 8343.2-1999 Horizontal woodworking band saw machine accuracy JB/T8343.2-1999 Standard download decompression password: www.bzxz.net
Some standard content:
1CS 79.120.10 Machinery Industry Standard of the People's Republic of China JB/T8343.1~8343.2—199 Horizontal Woodworking Band Saw Published on 1999-05-14 State Machinery Industry Bureau 2000-01-01 Implementation JBT8343.2—1999www.bzxz.net This standard is a revision of ZBJ65011-89 (Horizontal Woodworking Machine Tool Accuracy). During the revision, only the editorial changes were made according to the relevant regulations, and the technical content remained unchanged. This standard replaces ZBJ65011-B9 from the date of implementation. This standard was proposed by the National Technical Committee for Standardization of Woodworking Machine Tools and Knives. The drafting unit of this standard is Zhiyang Machinery Co., Ltd. The main drafters of the standard are Wang Zaihong, Li Zhijie and Han Hui. This standard was issued on March 31, 1989. H is published for the first time. Scope Machinery Industry Standard of the People's Republic of China Accuracy of Horizontal Woodworking Band Saws Accuracy of horizontal woodworking band saws This standard specifies the requirements and test methods for the geometry and working accuracy of horizontal woodworking band saws. This standard is applicable to horizontal woodworking band saws for processing board skin. Reference Standards JB/T8343.7-1999 The following standards contain provisions, which are generally The clauses of this standard are constituted by reference in this standard. When the standard version is in effect, the above mentioned terms are valid. All standards will be revised. Parties using this standard should explore the possibility of using the latest versions of the following standards. G8/18170-1987 JB/T41711999 3.1 When using this standard, refer to J8/T41713.2 for the results of machine tool inspection. According to JB4177-1999, adjust the installation level of the machine tool. The horizontal and lateral readings of the water meter placed on the workbench shall not exceed 0.1010003. The order of the precision inspection items listed in this standard does not represent the actual inspection order. For the purpose of assembly and disassembly inspection tools and inspection sequence: inspection can be carried out in any order. 3.4 When the actual measured length is different from the length specified in the standard, it shall be converted according to the provisions of 2.2.1.1 of JB4171-1999 according to the length that can be measured. The product minimum conversion value is 0.01 plus. The static approximation of the number in the disassembly calculation shall comply with the provisions of H/[8170. The accuracy inspection is shown in Table 1. The inspection method of the super-directional jump of the world wheel with a height of 1250 mm is approved by the State Bureau of Machinery Industry on May 1, 1999. The inspection method of the actual shear work is shown in Table 2. JBT83433—1999 Table 1 (end) Test items Saw wheel surface Flatness of blasting table surface Straightness in longitudinal and axial directions b. Shallow diagonal Linearity Steel surface flatness Before cutting: or inspection) conditions Test piece water content does not exceed 15%, the required height is 50 pine or other soft material, straightness without bleeding surface 1000: 0.2 b. Specification by section c. The quality of the situation must be consistent with the requirements of the price. D<1250 D=12500.10 Factory workbench length>630-1250 1 Workbench length>630-[2]0 1 Step D.10 Inspection items Thin board Juice: When testing the length of the board, avoid large defects (such as sugar edge, increase edge) Valley type Inspection force method Multi-photo 141711999 Relevant provisions of 4.4 2.2.2.1 During the inspection, the machine shall be monitored for lifting and lowering. 1. The operating table shall be in the maximum "maximum" position and then in the two small positions. The relevant procedures of the inspection method [B/T 4171-1999] shall be followed. Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.