JB/T 2001.73-1999 45° serrated thread profile and basic dimensions for water systems
Basic Information
Standard ID:
JB/T 2001.73-1999
Standard Name: 45° serrated thread profile and basic dimensions for water systems
Chinese Name:
水系统 45°锯齿形螺纹 牙型与基本尺寸
Standard category:Machinery Industry Standard (JB)
state:in force
Date of Release1999-06-28
Date of Implementation:2000-01-01
standard classification number
Standard ICS number:Fluid systems and general parts >> 23.100 Fluid power systems
Standard Classification Number:Machinery>>General Parts>>J20 Hydraulic and Pneumatic Devices
Publication information
other information
Focal point unit:Metallurgical Equipment Standardization Technical Committee
Publishing department:Metallurgical Equipment Standardization Technical Committee
Introduction to standards:
JB/T 2001.73-1999 This standard is a revision of JB 2076-84 "45° serrated thread profile and basic dimensions for hydraulic presses". This standard specifies the 45° serrated thread profile and basic dimensions. This standard applies to 45° serrated threads for press columns. This standard was first published in 1984. JB/T 2001.73-1999 45° serrated thread profile and basic dimensions for water systems JB/T2001.73-1999 Standard download decompression password: www.bzxz.net
Some standard content:
IC.s$ 23.110
Machinery Industry Standard of the People's Republic of China
JB/T 2001.1~2001.74—1999
Water system assembly and parts
Water system assembly and parts1999-06-28 Issued
State Machinery Industry Bureau
2(-01-U1 Implementation
Machinery Industry Standard of the People's Republic of China
Water System 45° Sawtooth Thread
Tooth Type and Basic Size
Watersystem—45dcgrceyaw-toothhrcadToothpaflernandbasicsize
The standard specifies the type and basic size of 45° serrated thread. This standard applies to 45° serrated thread for mechanical vertical use. 2 Type and size
2.1 According to the provisions of Figure 1 and Table 1.
2.1 Basic size According to the provisions of Table 2:
National Accessories
Foreign Control
IB21.73—199
Generation Police 2074
JI-r e-0.25 2-0.02 +0.[6 h-0.575 1 -0.1751 /vJ~0.51 1,-eu.25?Figure 1
Explosion height
Tooth filling
Using the same school chain
Guodong Machinery Industry Bureau 1009-06-28 approved fear
Root business degree
Tooth width
fi fi4
Return angle required diameter
2000-11-01 implementation
JB/T2001.731999wwW.bzxz.Net
Inner and outer butterfly drive
External stroke
Internal thread
External effect and station
3 Marking and example
JE/T200J.73-1999
Table 21 end)
Inner and outer effect
External coiling
11385:3| |tt||3.1 The 45° sawtooth thread for hydraulic presses is indicated by the letters "YS diameter × pitch/number of threads, spiral direction". The number of threads does not need to be indicated for single-thread threads, and the spiral direction is not indicated for non-threaded threads.
3.2 Marking indication
Example 1: The outer diameter of the screw is 250mm, the pitch is Bmm, the left-handed single-thread staggered thread: Y5250×SJB/T2001.73-1999
Example 2: The outer diameter of the screw is 300mm, the pitch is 10mm, the right-handed single-thread serrated thread: YS 300x10JB2001.73-1999
3: The outer diameter of the screw is 520mm, the pitch is 20, and the right-handed single-thread serrated thread: YS 520x20JB.T2001731999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.