JB/T 2001.1-1999 Types and dimensions of plunger glands for water systems (PN=31.5MPa)
Basic Information
Standard ID:
JB/T 2001.1-1999
Standard Name: Types and dimensions of plunger glands for water systems (PN=31.5MPa)
Chinese Name:
水系统 柱塞压盖 型式与尺寸(PN=31.5MPa)
Standard category:Machinery Industry Standard (JB)
state:in force
Date of Release1999-06-28
Date of Implementation:2000-01-01
standard classification number
Standard ICS number:Fluid systems and general parts >> 23.100 Fluid power systems
Standard Classification Number:Machinery>>General Parts>>J20 Hydraulic and Pneumatic Devices
Publication information
other information
Focal point unit:Metallurgical Equipment Standardization Technical Committee
Publishing department:Metallurgical Equipment Standardization Technical Committee
Introduction to standards:
JB/T 2001.1-1999 This standard is a revision of JB 2001-84 "Type and size of plunger gland for hydraulic press (Pg=315×100000Pa)". This standard specifies the type and size of plunger gland for working cylinder seal. This standard is applicable to plunger gland for various working cylinder seals with nominal pressure of 31.5MPa. This standard was first issued on 1984. JB/T 2001.1-1999 Type and size of plunger gland for water system (PN=31.5MPa) JB/T2001.1-1999 Standard download decompression password: www.bzxz.net
Some standard content:
IC.s$ 23.110
Standard of the Machinery Industry of the People's Republic of China
JB/T 2001.1~2001.74—1999
Water system assembly and parts1999-06-28 Issued
State Machinery Industry Bureau
2(-01-U1 Implementation
Standard of the Machinery Industry of the People's Republic of China
Water system-Plug gland-Type and sizt( PN=31.5 MPa ]
People's standard stipulates the form and size of the cylinder seal case gland, the standard applies to the following nominal pressure 35MTa each part of the cylinder seal design, the form and size
2. The half type should comply with the provisions of [.
One pressure: 2 one group: 3. Shift year, 4 structure dragon life short: 5.--, 6; ant: B bolt
2. 2 size, the amount of compliance with the network 1, Table 1 of the view of the State Machinery Industry Bureau approved on June 28, 1999 JB/T2001.1-1
JB2X84
2000-01-01 implementation
JBT2001.L.1
IBT 200.1.2
JH ZUKJ3 | 001.F.10
JB:T 2001.1.11
IR:T 200J.I.12
JR/I 2(KI1.1.T3
JB.T 2(OI.I.14
JDT2001.1.15
JBT 2001.1.16
JHT 2001.1.J7
JH- ZU011 18
JBT2(001,1.19
JB.T 2001.1.20
JB7T 2001.1.21
JB-T 2001.1.22
IR/1 2K11 1.2
JB/T 2001.1.24
JB/J 2001.1.25 : 260
JB/1 2001.1.26 : 2RO
1B/T20C1.1.27
JBT 2X1.1.2B
JBT 20 14
IB/T 200L.1.30
:kT 201.1.31
2001.1.33
2BVT2001.1.33
JB/T 2001.11999
6× M20
hk M24
8 ×M30
10×M3[
12×M36×3wwW.bzxz.Net
12×M42×3
1 ×M14 ×1.5
2 × M14 × 1.5 | |tt | .1.40
JH:1 7111 1.41
JB/T2U01 1.43
JT/T 2n01.1.45
1BT2001.1.44
11/1 211.1.4.5
JB-T20H0]46
1TT 2001.1.47
J1 20m1.t.48
J5-T20011.49
IK-T 2001.L.50
J6 2(KJ) 1 51
1I3/T 2001.1.52
JB 2001 1.53
Marking example
Injection gland with diameter of 10m1m:
JB/T 2001.1-1999
Table "(End;
Column half pressure range 4GJD/T2001.1—1999
16 × 42 × 3
16 48x3
ZI V48 ×:3
20 |tt||24 ×6i ×4
n X ci
4×M:4×
6 × M14× 1 5
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.