Some standard content:
GB12982-1996 | GB12982-91 "National Flag" has been revised. Some cited standards were deleted in the preparation of the standard; some technical requirements were added, such as: it was clarified that man-made fiber fabrics cannot be used to make the national flag; the standard size and allowable error of the national flag were added to the project content, and each specific data was given; The dimensions of car flags, signature flags, and table flags have been increased; further provisions have been made on national flag sewing, five-star yellow printing technology, packaging, and logos. This standard will replace GB12982-91 from the effective date. Appendix A and Appendix B of this standard are appendices to the standard. This standard is proposed by the State Administration of Technical Supervision. This standard is under the jurisdiction of the Standardization Department of the State Administration of Technical Supervision. This standard is drafted by the National Forehead Color Standardization Technical Committee. This standard was first published on May 25, 1991, and was first revised on December 25, 1996. 1 Scope
National Standard of the People's Republic of China
National
Flag
National flag
GB12982—1996
Replaces GB12982—91|| tt||This standard specifies the appearance quality (shape, flag pattern, plate making positioning, standard size, flag color) dyeing fastness, flag sewing, flag evaluation, test methods, inspection rules, and packaging of the flag of the People's Republic of China. , technical requirements for signs. This standard applies to national flags made of cotton, silk, chemical fiber fabrics (excluding man-made fiber fabrics), and also applies to national flags made of wool and linen fabrics. The appearance quality control of national flags made of paper, plastic and other materials should also refer to this standard. 2 Referenced standards
The provisions contained in the following standards constitute provisions of this standard by being quoted in this standard. At the time of publication, the editions indicated were valid. All standards are subject to revision and parties using this standard should explore the possibility of using the latest version of the standard listed below. GB250-1995 Gray sample card for evaluating discoloration GB/T3921-1996 Test method for color fastness of textiles to washing GB/T8427-1987 Test method for color fastness of textiles to light Xenon arc GB/T8430-1987 Test method for color fastness of textiles to weathering Xenon Arc GB129831991 National Flag Color Standard Sample
3 Definitions
This standard adopts the following definitions.
3.1 National flag red refers to the red color within a specific red range on the chromaticity diagram. 3.2 The five-star yellow of the national flag refers to the yellow within a specific yellow range on the chromaticity diagram. 3.3 The white of the flagpole cover refers to the white of the specific reflectance of the flagpole cover fabric. 4 Requirements
4.1 The shape, pattern and standard size of the national flag 4.1.1 The shape and pattern of the national flag shall be in accordance with the relevant provisions of the "Flag Law of the People's Republic of China" and "Instructions for the Flag Production Law". See Appendix A (standard appendix) and Figure 1.
4.1.2 The standard size and allowable error of the flag are shown in Table 1 and Figure 2. 4.1.3 When making a non-standard size flag due to special needs, it shall be enlarged or reduced in proportion to the standard size and allowable error. State Bureau of Technical Supervision approved the implementation on 1997-02-01 on 1996-12-25
Flag
Regulations
Length
mm||tt ||Height
mm
The diameter of the circumcircle of the big five-pointed star, mm
The diameter of the circumcircle of the small five-pointed star, mm
The distance between the upper corner of the big star and the top of the flag, mm
The distance between the upper corner of the big star and the flag cover, mm
The height of the lower corner of the small star from the center line of the flag
, mm
The oblique length of the big star\| | tt | )
Figure 1
Table 1
No. 1
2880
1920
576±10
192±4
192±10
480±10
S
24
30
80~85
GB12982—1996
Flag pattern of the People's Republic of China
Flag standard size and allowable error
No. 2
2400±12
1600±
480± 10
160±3
160±10
400±10
4
20
24
70~ 75
1) The calculation method for the oblique length of large stars is shown in Appendix B (Standard Appendix) No. 3
1920±8
1280±4*
384±8| |tt||128±3
128±8
320±8
3
15
20
60~65| |tt||No. 4
1440±1
960±*
288±6
96±2
96±8||tt| |240±8
2
12
20
50~55
0°
No. 5
960 ±4
640±*
192±4
64±2
64±8
160±8
2|| tt||10
15
40^45
car flag
300=
200=
60±2||tt ||20-1
20±4
50±4
0
1525
Signature flag
210=1|| tt||140±1
42±2
14±1
14±2
35±2
0
1016
Table flag
150±
100
30±1
10±1
10±2
25 ±2
0
8~~12
draw
of
C
generation
GB12982||tt ||2—1996
Country
2
Picture
4.2 Flag color and allowable error
GB12982—1996
4.2.1 The red color of the national flag made of cotton, silk and chemical fiber fabrics shall be based on the red colors of cotton, silk and chemical fiber fabrics in GB12983 respectively. When evaluated according to GB250, the color difference shall not be less than 3 to 4 levels. 4.2.2 The five-star yellow of the national flag:
4.2.2.1 The five-star yellow of the national flag made of cotton, silk, and chemical fiber fabrics shall be based on the five-star yellow of cotton, silk, and chemical fiber fabrics in GB12983 respectively. When evaluated according to GB250, the color difference shall not be less than 3 to 4 levels. 4.2.2.2 The five-star yellow color in the national flag made of cotton, silk, or chemical fiber fabrics must be made by the discharge printing process of textile fabrics when used outdoors. Sewing, patching, painting, etc. are not allowed. 4.2.3 The white color of the flagpole cover shall be subject to the white color of the flagpole cover in GB12983. When evaluated according to GB250, the color difference shall not be less than 3 to 4 levels. Metal or plastic rings that are in harmony with the color of the flag and the flagpole cover are allowed to be placed at appropriate positions on the upper and lower ends of the flagpole cover. The length of the flagpole cover is allowed to be appropriately longer than the height of the flag.
4.2.4 The color of the national flag made of wool and linen fabrics shall be based on the national flag red and five-star yellow colors of silk in GB12983. When evaluated according to GB250, the color difference shall not be less than 3~4 levels. 4.3 Flag color fastness
The national flag color fastness is shown in Table 2.
Table 2 National Flag Dyeing Fastness
Material
Quality
Cotton, chemical fiber fabric
Silk
Item
Color fastness to light
Color fastness to weather
Day
Color fastness to washing (fading as it is)
Color fastness to light
Climate resistance Color fastness
Color fastness to washing (fading as it is)
Red
Color
Level 4~5
Level 3
Level 3~4
Level 3
Level 3
Level 3~4
The dye fastness of national flags made of wool or linen fabrics shall not be lower than Table 2 Requirements for medium silk materials. 4.4 Flag sewing
yellow
color
level 4
level 3
level 3~4
level 3||tt| |Level 3
Level 3~4
4.4.1 The seams on the flag surface are: No. 1, 2, and 3 flags. Only one seam is allowed on the flag surface: below No. 4 flag (Including the No. 4 flag) No splicing seams are allowed on the flag surface; only horizontal splicing is allowed on the flag surface, vertical splicing is not allowed; no wool yarn is allowed to be exposed at the splicing joints. 4.4.21~The seams around the No. 5 flag and the car flag are double stitches. 4.4.3 The number of sewing stitches around the flag, the seam of the flag surface, the seam of the flagpole cover and the flag surface is 42 to 46 stitches per 100mm. Sewing stitches should be straight and wrinkle-free.
4.5 Flag surface evaluation
The flag surface evaluation is based on each flag, and the flag surface is inspected. The inspection items are shown in Table 3. Table 3 Flag evaluation
Item
Red part
Yellow part
Color difference between the upper, middle and lower flag
Flag appearance||tt| |Object
Request
Request
No obvious stains, colors, stains or wrinkles are allowed. No obvious stains or stains are allowed. Five-pointed stars are not allowed. When the obvious outline is evaluated according to GB250, it shall not be lower than level 4. White edges, dark and light edges, and weaving defects that obviously affect the appearance of the flag are not allowed. It is not allowed to add decorations, text or other patterns on the flag surface (including the front and back sides) and the withered edges. 5 Test Methods | 5.2 Test method for flag color fastness.
5.2.1 The color fastness to light test shall be carried out in accordance with the provisions of 6.2.3 in GB/T8427. 5.2.2 The weather color fastness test shall be carried out in accordance with the provisions of 6.4 in GB/T8430. 5.2.3 The color fastness test to washing is carried out in accordance with the provisions of 6.3.2 in GB/T3921. Method 1 is used for silk and chemical fiber fabrics, and method 3 is used for cotton fabrics.
5.3 The standard size and allowable error of the flag should be measured using inspected measuring tools with an accuracy of not less than 0.5%. 5.4 The national flag appearance evaluation test is carried out under bright natural light at a distance of 1m from the flag surface, and visual judgment is made. When using light inspection, daylight-colored fluorescent lamps must be used, and the illumination shall not be less than 7501x. 6 Inspection Rules
6.1 The shape, pattern and standard size of the flag, flag evaluation, flag sewing, and color quality inspection are factory inspections. Type inspection should be carried out when materials, dyes and processes change.
6.2 The number of inspection samples for each batch of products shall be 2% of the total number of products in the batch, but shall not be less than 10; samples shall be randomly selected. 6.3 During the inspection of each batch of products, if all the inspection items of each sample are qualified, the sample will be judged to be qualified; when all samples are qualified, the batch of products will be judged to be qualified, otherwise it will be judged to be unqualified. Unqualified products shall not leave the factory. 7 Packaging and Logo
7.1 Each national flag should be packaged separately, and the specifications, material, and manufacturer name should be indicated on the package. 7.2 The outer packaging of batches of national flags should ensure that the quality of the finished product is not damaged and facilitate transportation. The outer packaging should be marked with: product name, specifications, material, quantity, manufacturer name, dimensions, weight, and safe transportation signs. 7.3 Each flag should be accompanied by the manufacturer's logo. The logo is attached to the lower end of the flagpole cover. The dimensions of the flag in all directions shall not be larger than the width of the flagpole cover. The logos of car flags, signature flags, and table flags can be printed on the inside of the lower end of the flagpole cover or on the lower right side of the single-sided outer packaging bag. GB12982-1996
Appendix A
(subject appendix)
Instructions on the flag making law
(First Plenary Session of the Chinese People’s Political Consultative Conference on September 28, 1949 Announced by the Presidium) The shape and color of the national flag are the same on both sides, and the five stars on the flag face each other. For convenience, this article only uses the flagpole on the left side as the standard for illustration. For flagpoles on the right side, all references to left in this article should be changed to right, and all references to right in this document should be changed to left. (1) The flag is red and rectangular. Its length and height are in the ratio of three to two. There are five yellow five-pointed stars on the upper left corner of the flag. The first star is larger, and its circumscribed circle has a diameter of three-tenths of the flag's height, and is located on the left; the fourth star is smaller, and its circumscribed circle has a diameter of one-tenth of the flag's height, and is arched to the right of the big star. The flagpole cover is white.
(2) The position and drawing method of the five stars are as follows: A, in order to easily determine the position of the five stars, first divide the flag surface into four equal rectangles, and divide the upper left rectangle into ten equal parts. Divide left and right into fifteen equal parts.
B, the center point of the big five-pointed star is located at five points on the top of the rectangle, five on the bottom, five on the left and ten on the right. The drawing method is: take this point as the center of the circle, and divide the radius into three equal parts to draw a circle. On this circle, identify five equidistant points, one of which must be directly above the circle, and then connect two points that are apart from each other so that they form a straight line. The outer contour line formed by these five straight lines is the required large five-pointed star, with one tip of the five-pointed star facing upwards.
C． The center points of the four small five-pointed stars are: the first point is at the top, second and bottom points of the rectangle, ten and five points from the left and right, the second point is at the four and six points from the top, the left and three points from the left and the third point, and the third point is at the top and seven points. Three below, twelve left and three right, and the fourth point is nine one above, fifteen left and five. The drawing method is: take the above four points as the center of the circle, divide the radius into equal parts, and draw four circles respectively. Determine five equidistant points on each circle, one of which must be located on the connecting line between the center point of the big five-pointed star and the centers of the above four circles, and then use the same method to form the big five-pointed star to form a small Pentagram. Each of the four small five-pointed stars has one tip facing the center point of the large five-pointed star. (3) The general standards for the national flag are set as the following five, and all walks of life can choose to use them as appropriate: A. 288 cm long and 192 cm high.
B． 240 cm long and 160 cm high.
C, 192 cm long and 128 cm high.
Ding, 144 cm long and 96 cm high.
E, 96 cm long and 64 cm high. | |tt | (perpendicular to the upper and lower sides) neatly fold in half, with the fold line as the vertical axis, and then draw two parallel lines parallel to the fabric edge from the top angle A of the big star and the bottom B of the big star valley, intersecting with the fold line EF at C and D. The length difference between AC and BD is the oblique length of the large star (see Figure B1). The flagpole is covered with white
The top of the national flag
Picture B1
10 equal lines
E
A is a large star at the top; B is a large star at the bottom; EF - 13 bisectors of the folding line after aligning the edges of the full-width national flag cloth
vertical folding line
(vertical axis of the flag)
horizontal folding line
(horizontal folding line of the flag axis)
5 Flag Assessment
Flag assessment is conducted on each flag as a unit. The inspection items are shown in Table 3. Table 3 Flag Assessment
Items
Red part
Yellow part
Color difference between the upper, middle and lower parts of the flag
Flag Appearance
Items
Requirements
No obvious stains, overlapping colors, color smears or wrinkles are allowed. No obvious stains or color smears are allowed. The five-pointed star is not allowed to have an obvious unclear outline. When assessed according to GB250, it should not be lower than Grade 4. No white edges, dark or shallow edges or fabric defects that obviously affect the appearance are allowed. No additional decorations, text or other patterns are allowed on the flag (including the front and back sides) and the edges. 5 Test Methods
GB12982-1996
5.1 The method for assessing the color difference of the national flag shall be carried out according to GB250. 5.2 Test methods for color fastness of national flag.
5.2.1 The test for color fastness to light shall be carried out in accordance with 6.2.3 of GB/T8427. 5.2.2 The test for color fastness to weathering shall be carried out in accordance with 6.4 of GB/T8430. 5.2.3 The test for color fastness to washing shall be carried out in accordance with 6.3.2 of GB/T3921, where method 1 shall be used for silk and chemical fiber fabrics and method 3 for cotton fabrics.
5.3 The measurement of the standard size and allowable error of the national flag shall be carried out using qualified measuring tools with an accuracy of not less than 0.5%. 5.4 The test for the appearance evaluation of the national flag shall be carried out under bright natural light at a distance of 1m from the flag, and visual judgment shall be made. When using light inspection, daylight fluorescent lamps shall be used with an illumination of not less than 7501x. 6 Inspection rules
6.1 The shape, pattern and standard size of the flag, flag evaluation, national flag sewing, and color quality inspection are factory inspections. When the material, dye, or process changes, a type inspection should be carried out.
6.2 The number of samples for each batch of products to be inspected shall be 2% of the total number of products in the batch, but shall not be less than 10; samples shall be randomly selected. 6.3 In the inspection of each batch of products, if all the inspection items of each sample are qualified, the sample shall be judged as qualified; when all samples are qualified, the batch of products shall be judged as qualified products, otherwise they shall be unqualified products. Unqualified products shall not be shipped out of the factory. 7 Packaging and marking
7.1 Each national flag shall be packed separately, and the specifications, materials, and manufacturer's name shall be indicated on the packaging. 7.2 The outer packaging of batches of national flags shall ensure that the quality of the finished products is not damaged and is convenient for transportation. The outer packaging shall indicate: product name, specifications, materials, quantity, manufacturer's name, external dimensions, weight, and safe transportation mark. 7.3 Each national flag shall be accompanied by the manufacturer's mark. The mark shall be at the lower end of the flagpole cover. The dimensions of the mark in each direction shall not be greater than the width of the flagpole cover. The logo of the car flag, signature flag and table flag can be pasted and printed on the lower end of the flagpole cover or on the lower right side of the single-sided outer packaging bag. GB12982-1996
Appendix A
(Appendix to the title)
Instructions on the production method of the national flag
(Announced by the Presidium of the First Plenary Session of the Chinese People's Political Consultative Conference on September 28, 1949) The shape and color of the national flag are the same on both sides, and the five stars on the flag are opposite to each other. For convenience, this document only uses the side with the flagpole on the left as the standard for explanation. For the side with the flagpole on the right, all the left in this document should be changed to right, and all the right should be changed to left. (I) The flag is red and rectangular, with a ratio of three to two in length and height. There are five yellow five-pointed stars on the upper left of the flag. One star is larger, with a diameter of its circumscribed circle of three tenths of the flag height, and is on the left; four stars are smaller, with a diameter of its circumscribed circle of one tenth of the flag height, and are arched to the right of the large star. The flagpole cover is white. Www.bzxZ.net
(II) The position and drawing method of the five-pointed star are as follows: A. To facilitate the determination of the position of the five-pointed star, first divide the flag face into four equal rectangles, and divide the upper left rectangle into ten equal parts, and the left and right rectangles into fifteen equal parts.
B. The center point of the large five-pointed star is at the point where the upper and lower fives, the left and right tens of the rectangle are divided into five equal parts. The drawing method is: take this point as the center of the circle, and draw a circle with three equal parts as the radius. On the circumference of this circle, determine five points of equal distance, one of which must be located directly above the circle, and then connect the two points separated by each other among the five points to form a straight line. The outer contour line formed by these five straight lines is the required large five-pointed star, and one of the corners of the five-pointed star is facing upward.
C. The center points of the four small five-pointed stars are: the first point is at the position of the rectangle 2 up, 8 down, 10 left and 5 right; the second point is at the position of the rectangle 4 up, 6 down, 12 left and 3 right; the third point is at the position of the rectangle 7 down, 3 down, 12 left and 3 right; the fourth point is at the position of the rectangle 9 down, 1 down, 10 left and 5 right. The method of drawing is: take the above four points as the center of the circle, and use one equal division as the radius to draw four circles respectively. On each circle, determine five points of equal distance, and each of them must have a point located on the connecting line between the center point of the big five-pointed star and the centers of the above four circles. Then, use the same method to form the big five-pointed star to form the small five-pointed star. Each of these four small five-pointed stars has a corner point facing the center point of the big five-pointed star. (III) The general size of the national flag is set as follows, and each sector can choose according to its own circumstances: A. Length 288 cm, height 192 cm.
B. Length 240 cm, height 160 cm.
C. Length 192 cm, height 128 cm.
D, length 144 cm, height 96 cm.
E, length 96 cm, height 64 cm.
GB12982-1996
Appendix B
(Appendix to the standard)
Calculation method of the oblique length of the large star on the national flag
Take the entire national flag cloth, fold it neatly along the edge of the cloth (perpendicular to the upper and lower sides), take its fold line as the vertical axis, and then draw two parallel lines parallel to the cloth edge with the top angle A of the large star and the bottom of the large star B respectively, and intersect with the fold line EF at C and D. The difference between the lengths of AC and BD is the oblique length of the large star (see Figure B1). Flagpole white
Top of the national flag
Figure B1
10-point dividing line
E
A A large star top corner; B A large star valley bottom; EF A folding line after the edges of the full national flag cloth are aligned 13-point dividing line
Vertical folding line
(Vertical axis of the national flag)
Horizontal folding line
(Horizontal axis of the national flag)
5 Flag surface evaluation
Flag surface evaluation is based on each flag, and the flag surface is inspected. The inspection items are shown in Table 3. Table 3 Flag evaluation
Item
Red part
Yellow part
Color difference between the upper, middle and lower flag
Flag appearance||tt| |Object
Request
Request
No obvious stains, colors, stains or wrinkles are allowed. No obvious stains or stains are allowed. Five-pointed stars are not allowed. When the obvious outline is evaluated according to GB250, it shall not be lower than level 4. White edges, dark and light edges, and weaving defects that obviously affect the appearance of the flag are not allowed. It is not allowed to add decorations, text or other patterns on the flag surface (including the front and back sides) and the withered edges. 5 Test Methods | 5.2 Test method for flag color fastness.
5.2.1 The color fastness to light test shall be carried out in accordance with the provisions of 6.2.3 in GB/T8427. 5.2.2 The weather color fastness test shall be carried out in accordance with the provisions of 6.4 in GB/T8430. 5.2.3 The color fastness test to washing is carried out in accordance with the provisions of 6.3.2 in GB/T3921. Method 1 is used for silk and chemical fiber fabrics, and method 3 is used for cotton fabrics.
5.3 The standard size and allowable error of the flag should be measured using inspected measuring tools with an accuracy of not less than 0.5%. 5.4 The national flag appearance evaluation test is carried out under bright natural light at a distance of 1m from the flag surface, and visual judgment is made. When using light inspection, daylight-colored fluorescent lamps must be used, and the illumination shall not be less than 7501x. 6 Inspection Rules
6.1 The shape, pattern and standard size of the flag, flag evaluation, flag sewing, and color quality inspection are factory inspections. Type inspection should be carried out when materials, dyes and processes change.
6.2 The number of inspection samples for each batch of products shall be 2% of the total number of products in the batch, but shall not be less than 10; samples shall be randomly selected. 6.3 During the inspection of each batch of products, if all the inspection items of each sample are qualified, the sample will be judged to be qualified; when all samples are qualified, the batch of products will be judged to be qualified, otherwise it will be judged to be unqualified. Unqualified products shall not leave the factory. 7 Packaging and Logo
7.1 Each national flag should be packaged separately, and the specifications, material, and manufacturer name should be indicated on the package. 7.2 The outer packaging of batches of national flags should ensure that the quality of the finished product is not damaged and facilitate transportation. The outer packaging should be marked with: product name, specifications, material, quantity, manufacturer name, dimensions, weight, and safe transportation signs. 7.3 Each flag should be accompanied by the manufacturer's logo. The logo is attached to the lower end of the flagpole cover. The dimensions of the flag in all directions shall not be greater than the width of the flagpole cover. The logos of car flags, signature flags, and table flags can be printed on the inside of the lower end of the flagpole cover or on the lower right side of the single-sided outer packaging bag. GB12982-1996
Appendix A
(subject appendix)
Instructions on the flag making law
(First Plenary Session of the Chinese People’s Political Consultative Conference on September 28, 1949 Announced by the Presidium) The shape and color of the national flag are the same on both sides, and the five stars on the flag face each other. For convenience, this article only uses the flagpole on the left side as the standard for illustration. For flagpoles on the right side, all references to left in this article should be changed to right, and all references to right in this document should be changed to left. (1) The flag is red and rectangular. Its length and height are in the ratio of three to two. There are five yellow five-pointed stars on the upper left corner of the flag. The first star is larger, and its circumscribed circle has a diameter of three-tenths of the flag's height, and is located on the left; the fourth star is smaller, and its circumscribed circle has a diameter of one-tenth of the flag's height, and is arched to the right of the big star. The flagpole cover is white.
(2) The position and drawing method of the five stars are as follows: A, in order to easily determine the position of the five stars, first divide the flag surface into four equal rectangles, and divide the upper left rectangle into ten equal parts. Divide left and right into fifteen equal parts.
B, the center point of the big five-pointed star is located at five points on the top of the rectangle, five on the bottom, five on the left and ten on the right. The drawing method is: take this point as the center of the circle, and divide the radius into three equal parts to draw a circle. On this circle, identify five equidistant points, one of which must be directly above the circle, and then connect two points that are apart from each other so that they form a straight line. The outer contour line formed by these five straight lines is the required large five-pointed star, with one tip of the five-pointed star facing upwards.
C． The center points of the four small five-pointed stars are: the first point is at the top, second and bottom points of the rectangle, ten and five points from the left and right, the second point is at the four and six points from the top, the left and three points from the left and the third point, and the third point is at the top and seven points. Three below, twelve left and three right, and the fourth point is nine one above, fifteen left and five. The drawing method is: take the above four points as the center of the circle, divide the radius into equal parts, and draw four circles respectively. Determine five equidistant points on each circle, one of which must be located on the connecting line between the center point of the big five-pointed star and the centers of the above four circles, and then use the same method to form the big five-pointed star to form the small five-pointed star. Pentagram. Each of the four small five-pointed stars has one tip facing the center point of the large five-pointed star. (3) The general standards for the national flag are set as the following five, and all walks of life can choose to use them as appropriate: A. 288 cm long and 192 cm high.
B． 240 cm long and 160 cm high.
C, 192 cm long and 128 cm high.
Ding, 144 cm long and 96 cm high.
E, 96 cm long and 64 cm high. | |tt | (perpendicular to the upper and lower sides) neatly fold in half, with the fold line as the vertical axis, and then draw two parallel lines parallel to the fabric edge from the top angle A of the big star and the bottom B of the big star valley, intersecting with the fold line EF at C and D. The length difference between AC and BD is the oblique length of the large star (see Figure B1). The flagpole is covered with white
The top of the national flag
Picture B1
10 equal lines
E
A is a large star at the top; B is a large star at the bottom; EF - 13 bisectors of the folding line after aligning the edges of the full-width national flag cloth
vertical folding line
(vertical axis of the flag)
horizontal folding line
(horizontal folding line of the flag axis)
3. Each flag should be accompanied by the manufacturer's logo. The logo is attached to the lower end of the flagpole cover. The dimensions of the flag in all directions shall not be greater than the width of the flagpole cover. The logos of car flags, signature flags, and table flags can be printed on the inside of the lower end of the flagpole cover or on the lower right side of the single-sided outer packaging bag. GB12982-1996
Appendix A
(subject appendix)
Instructions on the flag making law
(First Plenary Session of the Chinese People’s Political Consultative Conference on September 28, 1949 Announced by the Presidium) The shape and color of the national flag are the same on both sides, and the five stars on the flag face each other. For convenience, this article only uses the flagpole on the left side as the standard for illustration. For flagpoles on the right side, all references to left in this article should be changed to right, and all references to right in this document should be changed to left. (1) The flag is red and rectangular. Its length and height are in the ratio of three to two. There are five yellow five-pointed stars on the upper left corner of the flag. The first star is larger, and its circumscribed circle has a diameter of three-tenths of the flag's height, and is located on the left; the fourth star is smaller, and its circumscribed circle has a diameter of one-tenth of the flag's height, and is arched to the right of the big star. The flagpole cover is white.
(2) The position and drawing method of the five stars are as follows: A, in order to easily determine the position of the five stars, first divide the flag surface into four equal rectangles, and divide the upper left rectangle into ten equal parts. Divide left and right into fifteen equal parts.
B, the center point of the big five-pointed star is located at five points on the top of the rectangle, five on the bottom, five on the left and ten on the right. The drawing method is: take this point as the center of the circle, and divide the radius into three equal parts to draw a circle. On this circle, identify five equidistant points, one of which must be directly above the circle, and then connect two points that are apart from each other so that they form a straight line. The outer contour line formed by these five straight lines is the required large five-pointed star, with one tip of the five-pointed star facing upwards.
C. The center points of the four small five-pointed stars are: the first point is at the top, second and bottom points of the rectangle, ten and five points from the left and right, the second point is at the four and six points from the top, the left and three points from the left and the third point, and the third point is at the top and seven points. Three below, twelve left and three right, and the fourth point is nine one above, fifteen left and five. The drawing method is: take the above four points as the center of the circle, divide the radius into equal parts, and draw four circles respectively. Determine five equidistant points on each circle, one of which must be located on the connecting line between the center point of the big five-pointed star and the centers of the above four circles, and then use the same method to form the big five-pointed star to form the small five-pointed star. Pentagram. Each of the four small five-pointed stars has one tip facing the center point of the large five-pointed star. (3) The general standards for the national flag are set as the following five, and all walks of life can choose to use them as appropriate: A. 288 cm long and 192 cm high.
B． 240 cm long and 160 cm high.
C, 192 cm long and 128 cm high.
Ding, 144 cm long and 96 cm high.
E, 96 cm long and 64 cm high. | |tt | (perpendicular to the upper and lower sides) neatly fold in half, with the fold line as the vertical axis, and then draw two parallel lines parallel to the fabric edge from the top angle A of the big star and the bottom B of the big star valley, intersecting with the fold line EF at C and D. The length difference between AC and BD is the oblique length of the large star (see Figure B1). The flagpole is covered with white
The top of the national flag
Picture B1
10 equal lines
E
A is a large star at the top; B is a large star at the bottom; EF - 13 bisectors of the folding line after aligning the edges of the full-width national flag cloth
vertical folding line
(vertical axis of the flag)
horizontal folding line
(horizontal folding line of the flag axis)
3. Each flag should be accompanied by the manufacturer's logo. The logo is attached to the lower end of the flagpole cover. The dimensions of the flag in all directions shall not be greater than the width of the flagpole cover. The logos of car flags, signature flags, and table flags can be printed on the inside of the lower end of the flagpole cover or on the lower right side of the single-sided outer packaging bag. GB12982-1996
Appendix A
(subject appendix)
Instructions on the flag making law
(First Plenary Session of the Chinese People’s Political Consultative Conference on September 28, 1949 Announced by the Presidium) The shape and color of the national flag are the same on both sides, and the five stars on the flag face each other. For convenience, this article only uses the flagpole on the left side as the standard for illustration. For flagpoles on the right side, all references to left in this article should be changed to right, and all references to right in this document should be changed to left. (1) The flag is red and rectangular. Its length and height are in the ratio of three to two. There are five yellow five-pointed stars on the upper left corner of the flag. The first star is larger, and its circumscribed circle has a diameter of three-tenths of the flag's height, and is located on the left; the fourth star is smaller, and its circumscribed circle has a diameter of one-tenth of the flag's height, and is arched to the right of the big star. The flagpole cover is white.
(2) The position and drawing method of the five stars are as follows: A, in order to easily determine the position of the five stars, first divide the flag surface into four equal rectangles, and divide the upper left rectangle into ten equal parts. Divide left and right into fifteen equal parts.
B, the center point of the big five-pointed star is located at five points on the top of the rectangle, five on the bottom, five on the left and ten on the right. The drawing method is: take this point as the center of the circle, and divide the radius into three equal parts to draw a circle. On this circle, identify five equidistant points, one of which must be directly above the circle, and then connect two points that are apart from each other so that they form a straight line. The outer contour line formed by these five straight lines is the required large five-pointed star, with one tip of the five-pointed star facing upwards.
C. The center points of the four small five-pointed stars are: the first point is at the top, second and bottom points of the rectangle, ten and five points from the left and right, the second point is at the four and six points from the top, the left and three points from the left and the third point, and the third point is at the top and seven points. Three below, twelve left and three right, the fourth point is nine one above, fifteen left and right. The drawing method is: take the above four points as the center of the circle, divide the radius into equal parts, and draw four circles respectively. Determine five equidistant points on each circle, one of which must be located on the connecting line between the center point of the big five-pointed star and the centers of the above four circles, and then use the same method to form the big five-pointed star to form the small five-pointed star. Pentagram. Each of the four small five-pointed stars has one tip facing the center point of the large five-pointed star. (3) The general standards for the national flag are set as the following five, and all walks of life can choose to use them as appropriate: A. 288 cm long and 192 cm high.
B． 240 cm long and 160 cm high.
C, 192 cm long and 128 cm high.
Ding, 144 cm long and 96 cm high.
E, 96 cm long and 64 cm high. | |tt | (perpendicular to the upper and lower sides) neatly fold in half, with the fold line as the vertical axis, and then draw two parallel lines parallel to the edge of the fabric from the top angle A of the big star and the bottom B of the big star, intersecting the fold line EF at C and D. The length difference between AC and BD is the oblique length of the large star (see Figure B1). The flagpole is covered with white
The top of the national flag
Picture B1
10 equal lines
E
A is a large star at the top; B is a large star at the bottom; EF - 13 bisectors of the folding line after aligning the edges of the full-width national flag cloth
vertical folding line
(vertical axis of the flag)
horizontal folding line
(horizontal folding line of the flag axis)
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.