SY/T 5029-1995 Sucker rods (sucker rod nipples, polished rods, couplings and reducing couplings)
Some standard content:
Petroleum and Natural Gas Industry Standard of the People's Republic of ChinaSY/T 50291995
eqyISO10428:1993
Sucker rods (sucker rod short joints, bare rods, couplings and reducing couplings
1995-12-25 Issued
China National Petroleum Corporation
1996-06-30 Implementation
ISO Preface
ISO Introduction
1 Model diagram
API Spec 11B 1990 24th edition
Appendix A (suggestive appendix)
Appendix H (suggestive appendix)
Sucker rods (sucker rod pup joints, polished rods, couplings and reducing couplings) Specification for one-end forged roughened rods and their couplings
Sucker rod material mechanical properties·
This standard is equivalent to ISO 10428:1993 "Sucker rods (sucker rod pup joints, polished rod couplings and reducing couplings) for petroleum and natural gas industries" Specification".
This standard supplements the recommended one-end upset polished rod and the mechanical properties of related sucker rod materials while equivalently adopting ISO10428:1993 (i.e. API Spec 11B 1990 24th edition). The guilty page and the back page of "supplement" in API Spec 11B, the notes on copying or translation, the use of the API monogram, the policy statement, the statement on the application for the license to use the API monogram, the API license agreement, and the list of calibration standard gauges...are deleted. The equivalent adoption of the international standard ISO10428:1993 makes the standards of the important parts of oil and gas production in my country - sucker rods (including sucker rod short section polished rods, couplings and reducing couplings) consistent with In line with international standards, adapting to the needs of international trade, technical and economic exchanges and participation in international standardization activities
When equivalently adopting ISO10428:1993 and converting it into the standard of this industry, in addition to adopting the full text of the standard, its writing format and method are used. The foreword and introduction of ISO10428:1993 and the foreword of API standard are retained. It should be pointed out here that there are some doubts and omissions in the ISO10428:1993 standard. When we converted it into the wood industry standard, we appropriately adopted corrective footnotes to explain it while maintaining the original text. This standard shall be implemented from June 30, 1996. This standard shall also replace S Y/T5029-93 "Sucker rods and their couplings" (GB722987), SY/T5058-93 "Sucker rods and their couplings", SY5282-91 "Sucker rod clamps" and SY/T5G42-93 "Sucker rod sealing box" (ZBE9201990).
Appendix A and Appendix B of this standard are reminder appendices. This standard is under the jurisdiction of the National Technical Committee for Standardization of Petroleum Drilling and Production Equipment and Tools. The responsible drafting units of this standard are: Petroleum Exploration and Development Research Institute of Petroleum Industry Standardization, Yumen Petroleum Administration Bureau Machinery. The participating drafting units of this standard are: Lanzhou Petroleum Machinery Research Institute, Northeast Oil Transportation Administration Bureau Tieling Machinery Factory Petroleum Pipe Research Institute. The main drafters of this standard are Wang Minqian, Qiang Shengcheng, Lei Yanying, Zhang Liying, and Yu Guigen.
ISO (International Organization for Standardization) is a joint organization of national standard bodies (ISO member groups) in the world. The work of formulating international standards is carried out through some ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Certain international organizations, governmental and non-governmental, in liaison with ISO also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by a deciding vote of at least 75 % of the member bodies.
International Standard ISO 10428 was prepared by the American Petroleum Institute (API) (as Spec 11B, 24th edition) and adopted under a specific "fast track procedure" by ISO 7TC67 Technical Committee on Materials, Equipment and Offshore Structures for the Petroleum and Natural Gas Industries and approved by the ISO member bodies.
ISO Introduction
International Standard ISO 10428:1993 Reproduction of API Spec 11B 24th edition, 1990, and Supplement 1 (1 April 1991). In recognizing API documents, ISO recognizes that these documents do not conform to all current ISO guidelines in terms of format and expression of international standards in certain aspects. Therefore, the relevant technical organizations in ISO/TC67 will review ISO10428:1993 and review it again in a format that conforms to the above guidelines when feasible. As for when and where to use this standard, this standard does not intend to exclude the need for reasonable engineering judgment: users of this standard should be aware that additional and different requirements are in line with the expected specific service needs. The standards referenced here may be replaced by other international standards or national standards. It can be shown that they meet or are superior to the requirements of the referenced standards. Appendix A of the API document "shall not be considered as a requirement part of this standard. Adoption instructions
1IAPISpeIIB Appendix A Use of API monogram' has been deleted from this standard, see the foreword. Scope
Petroleum and Natural Gas Industry Standard of the People's Republic of China SY/T 50291995*1
eqyIS010428:1993
Sucker rods (sucker rod pup joints, polished rods, couplings and reducers) This international standard specifies the dimensional characteristics, chemical and mechanical properties, and measurement methods of sucker rods (sucker rod pup joints, polished rods, couplings and reducers) used in the petroleum and natural gas industry. 2 Requirements
The requirements are specified in the API Specification 11B (Spec 11B), 24th edition, 1990 - Sucker rods (sucker rod pup joints, polished rods, couplings and reducers) specification, which was adopted as ISO10428. However, as intended by international standardization, the changes shall apply to the specified chapters and clauses of the publication API Spec 11B. These changes are briefly described below.
Throughout the publication API Spec 11B, the conversion of English units shall be made in accordance with ISO 31\. Length 1 inch (in) = 25.4 mm (exact value) 1 foot (fl) = 304.8 mm or 0.3048 m (exact value) Torque 1 foot pound force (ft*Ibf) = 1.355818 Nm Temperature Fahrenheit (°F) is converted to Celsius (℃) using the following formula ℃ = 5/9 (°F-32)
Page 6 "Instructions for Ordering Sucker Rods"
An order consistent with ISO 10428 may be added as needed. Page 13 2
The information given in the \Policy Statement\ is only relevant to API publications. Page 8 "Scope'
The information given in 1.3 to 1.6 is only relevant to API publications. Page 19 4.3.2.2
The referenced standard MIL-STD-105D should be replaced by the referenced standard ISO2859-1. *) #SY/T 5029-93.SY/T 5058-93.SY 5282-91, NY/T 5642-93. Adoption instructions:
11 Adopt GB3100-3102-93 "Quantities and Units". 3] This page number is the original page number of [S(10428 standard. API's \Policy Statement\ has been deleted from this standard. See the foreword. 3) Adopt GB2828-87 "Batch Inspection Count Sampling Procedure and Sampling Table (Applicable to Continuous Batch Inspection)". China National Petroleum and Natural Gas Corporation approved on December 25, 1995 and June 30, 1996 Implementation
Page 16 4.3.7
SY/ T 5029 --1995
The referenced standard MIL-STD-105D shall be replaced by the referenced standard ISO2859-1: Table 4.4 and Table 4.5bZxz.net
The referenced standard MIL-STD-105D shall be replaced by the referenced standard ISO285-1\, Page 24 6.1.21
When applicable, the X-grade gauge tolerances quoted in the National Bureau of Standards Manual H28 shall be supplemented by the referenced equivalent ISO tolerance grades. Page 43 Chapter 8 Gauge Verification
This chapter The rat gauge verification system specified is not considered as an integral part of this International Standard: the system should be a subject of future study by ISO/TC67 in order to establish an ISO or ISO/API verification system. The registration of verification bodies and standard gauges should be carried out in accordance with Annex N of Part 1 of the ISO/IEC Directives.
Page 47 Chapter 10 "Marking, packaging and wire protection\1c., 2c should add the option of products marked with "ISO10428\". In addition, in 1e.2e.3 and 10.2 The "identification code" mentioned in the example may be used as a reference: The marking in future revisions of this International Standard shall comply with the provisions of Annex E of Part 2 of the ISO/IEC Directives.
Page 51 12.9
The referenced standard MIL-STD-105D is replaced by the referenced standard ISO2859-1. Page 51 12.10\Footnote
This information is relevant only to API documents.
Selection table for products previously marked with \ISO10428\ 12.3
The referenced standard MIL-STD-105D should be replaced by the referenced standard ISO2859-1. Page 56 Appendix A\Use of the API Monogram" 3 Appendix A and other provisions concerning the use of the API Monogram should not be considered as an integral part of this International Standard. *）"(United States) National Bureau of Standards\ changed to (United States) National Institute of Standards and Technology\. Adoption instructions:
I1 adopts (:B282%-87 "Batch Inspection Count Sampling Procedure and Sampling Table (Applicable to Continuous Batch Inspection)" 2] The original text is mistakenly (.2.
3] The page number is [SO10428 standard original page number, Appendix A\Use of API monogram", which has been deleted in this standard. See the preface Specification for Sucker Rods (Pony Rads , Polished Rods, Couplings and Reducing Couplings)
Specification for Sucker Rods (Pony Rads , Polished Rods, Couplings and API Spec ii B 24th Edition October 1, 1990 Supplement 1 (April 1, 1991) Supplement 1 to Sucker Rods (Sucker Rod Pup Joints, Polished Rods, Couplings and Reducing Couplings) (API Spec 11 B 24th Edition October 1, 1990) API Foreword This supplement includes API Changes to Spec 11B (October 1H, 1990, 24th edition) Specification for Sucker Rods (Sucker Rod Nipples, Bare Rods, Couplings and Reducers). These changes were adopted at the 1990 Standardization Conference and written into the CircPS-1920 report and approved by letter vote.
Page 21, Table 5.3: Modify the following D. and C rod diameters
28.6(1 1/ 8)
12.7(1 / 2)
15.9(5 / 8)
19.1(3 / 4)
22.2(7 / 8)
28.6(1 (/ a)
47.37(1.865)
53.54(2.110)
0.66(0.026)
2.03(0.08)
2.03(0.08)
3.61 (0.142)
4.34(0.171)
Ordering Sucker Rod Frequency Judgment
API Foreword
Chapter 1
Chapter 2
Chapter 3
Chapter 3B
Chapter 4
Chapter 5
Chapter 6
Chapter 7
Chapter 8
Chapter 9
Chapter 10
Chapter 11
Chapter 12
Chapter 13
Chapter 14
Main Dimensions
Flanged Sucker Rod
Couplings and Reducing Couplings
Sucker rod: Inspection method for sucker rod pup joint, external thread and internal thread connection
Gauge specification
Gauge verification
Manufacturing quality and repair
Marking, packaging and thread protection
Acceptance and rejection
Sucker rod and polished rod bushing
Sealing box and oil pushing tee
· Polished rod card
Instructions for ordering sucker rods
When ordering sucker rods and couplings manufactured according to API Spec 11B, the user should indicate on the order: Technical specification
Rod end type
Coupling:
Reducing coupling
Selection note:
11 was mistakenly written as 4.4 in the original text.
API Spec [IB
See 2.1, Table 2.1
See 3.1. Table 3.1
See 3.1 and 3.1
See 3.2 and 3.3
API Foreword
a. This standard is under the jurisdiction of the American Petroleum Institute's Oil Production Equipment Standardization Committee. b. Attention Users of This Publication: Several portions of this publication have been revised from the previous edition, and the revisions are marked with bold black lines. Some of the revisions are substantial, and some are editorial adjustments. The bold black line markings are intended to help users identify the portions of this publication that have been revised from the previous edition, but API does not guarantee the accuracy of these bold black line markings. C: "This standard shall be effective as of the date printed on the cover, but may be used voluntarily from the date of issue. Note: This edition replaces the 23rd edition, published on October 1, 1989. This edition includes the changes adopted at the 1989 Standardization Conference and subsequently approved by letter vote.171)
Ordering Sucker Rods
API Foreword
Chapter 1
Chapter 3
Chapter 3B
Chapter 4
Chapter 5
Chapter 6
Chapter 7
Chapter 8
Chapter 9
Chapter 10
Chapter 11
Chapter 12
Chapter 13
Chapter 14
Main Dimensions
Flanged Sucker Rods
Couplings and Reducing Couplings
Sucker Rods: Sucker Rod Nipples, External Threads and Internal Threads Connection Inspection Methods
Gauges Standard
Gauge verification
Manufacturing quality and repair
Marking, packaging and wire protection
Acceptance and rejection
Northern rod and polished rod bushing
Seal box and oil pushing tee
· Polished rod card
Instructions for ordering sucker rods
When ordering sucker rods and couplings manufactured according to API Spec 11B, the user should indicate on the order: Technical specifications
Rod end type
Coupling:
Reducing coupling
Production note:
11 was mistakenly written as 4.4 in the original text.
API Spec [IB
See 2.1, Table 2.1
See 3.1. Table 3.1
See 3.1 and 3.1
See 3.2 and 3.3
API Foreword
a. This standard is under the jurisdiction of the American Petroleum Institute's Oil Production Equipment Standardization Committee. b. Attention Users of This Publication: Several portions of this publication have been revised from the previous edition, and the revisions are marked with bold black lines. Some of the revisions are substantial, and some are editorial adjustments. The bold black line markings are intended to help users identify the portions of this publication that have been revised from the previous edition, but API does not guarantee the accuracy of these bold black line markings. C: "This standard shall be effective as of the date printed on the cover, but may be used voluntarily from the date of issue. Note: This edition replaces the 23rd edition, published on October 1, 1989. This edition includes the changes adopted at the 1989 Standardization Conference and subsequently approved by letter vote.171)
Ordering Sucker Rods
API Foreword
Chapter 1
Chapter 3
Chapter 3B
Chapter 4
Chapter 5
Chapter 6
Chapter 7
Chapter 8
Chapter 9
Chapter 10
Chapter 11
Chapter 12
Chapter 13
Chapter 14
Main Dimensions
Flanged Sucker Rods
Couplings and Reducing Couplings
Sucker Rods: Sucker Rod Nipples, External Threads and Internal Threads Connection Inspection Methods
Gauges Standard
Gauge verification
Manufacturing quality and repair
Marking, packaging and wire protection
Acceptance and rejection
Northern rod and polished rod bushing
Seal box and oil pushing tee
· Polished rod card
Instructions for ordering sucker rods
When ordering sucker rods and couplings manufactured according to API Spec 11B, the user should indicate on the order: Technical specifications
Rod end type
Coupling:
Reducing coupling
Production note:
11 was mistakenly written as 4.4 in the original text.
API Spec [IB
See 2.1, Table 2.1
See 3.1. Table 3.1
See 3.1 and 3.1
See 3.2 and 3.3
API Foreword
a. This standard is under the jurisdiction of the American Petroleum Institute's Oil Production Equipment Standardization Committee. b. Attention Users of This Publication: Several portions of this publication have been revised from the previous edition, and the revisions are marked with bold black lines. Some of the revisions are substantial, and some are editorial adjustments. The bold black line markings are intended to help users identify the portions of this publication that have been revised from the previous edition, but API does not guarantee the accuracy of these bold black line markings. C: "This standard shall be effective as of the date printed on the cover, but may be used voluntarily from the date of issue. Note: This edition replaces the 23rd edition, published on October 1, 1989. This edition includes the changes adopted at the 1989 Standardization Conference and subsequently approved by letter vote.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.