Some standard content:
ICS37.100.01
National Standard of the People's Republic of China
GB/T7707—2008
Replaces GB/T7707-1987
The intaglio prints for decorating2008-07-02 Issued
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Standardization Administration of China
2008-12-01 Implementation
GB/T7707-2008
Normative references
Terms and definitions
Technical requirements
Test methods
6 Test rules
Marking, packaging, transportation, storage
Appendix A (Normative appendix)
References
Tape for ink fastness test
This standard replaces GB/T7707-1987 "Intaglio Decorating Printing". Compared with GB/T7707-1987, this standard has been modified as follows: the structure of the standard has been modified in accordance with GB/T1.1-2000; the "appearance", "registration error" and "solid printing requirements" in the first standard have been appropriately modified. Appendix A of this standard is a normative appendix.
This standard is proposed by the General Administration of Press and Publication.
This standard is under the jurisdiction of the National Technical Committee for Printing Standardization. GB/T7707-2008
The drafting units of this standard are: Shanghai Packaging and Paper (Group) Co., Ltd., Shanghai Station of National Quality Supervision and Inspection of Light Industry Packaging and Decoration Printing Products, National Light Industry Packaging Standardization Center, Shanghai Zijiang Color Printing and Packaging Co., Ltd., Zhangpu Color Printing Factory of Jiangsu Caihua Group Kunshan, Sichuan Chengdu Dingxin Packaging Printing Co., Ltd., and Packaging and Printing Committee of China Packaging Technology Association. The main drafters of this standard are: Zheng Shaonan, Chen Qixiang, Lu Jiaping, Hou Xiaoping, Bao Yanmin, Zhang Lisheng, and Huang Bo. This standard was first issued in 1987.
1 Scope
Intaglio Decorative Prints
This standard specifies the requirements, test methods, inspection rules, marking, packaging, transportation, etc. of intaglio decorative prints. GB/T7707-2008
This standard applies to plastic film and glass paper decorative prints and packaging composite film prints produced by intaglio printing. This standard does not apply to paper intaglio decorative prints. 2 Normative References
The clauses in the following documents become clauses of this standard through reference in this standard. For any dated referenced document, all subsequent amendments (excluding errata) or revisions are not applicable to this standard. However, the parties to an agreement based on this standard are encouraged to study whether the latest versions of these documents can be used. For any undated referenced document, the latest version shall apply to this standard. GB/T2792-1998 Determination of 180° peel strength of pressure-sensitive adhesive tape (eqvJISZ0237:1991) GB/T2828.1 Attribute sampling inspection procedure Part 1: Batch inspection sampling plan retrieved by acceptance quality limit (AQL) (GB/T2828.1-2003, ISO2859-1:1999, IDT) GB/T18722 Printing technology Reflection density measurement and colorimetry in printing process control Application in (GB/T18722-2002, cqvISO13656:2000)
CY/T3 Color evaluation Illumination and viewing conditions
ISO13655 Spectral measurement and colorimetric calculation of printed images ISO14981 Optical geometry and metrological conditions for reflection densitometers for printing ISO15994 Printing technology Test of printed products Visual gloss 3 Terms and definitions
The following terms and definitions apply to this standard. 3.1
recess printing
Gravure printing
A printing method in which the image part of the printing plate is lower than the non-image part. [GB/T9851.1—2008,5.12]
Halftone gravure
Gravure printing method in which the tone value is reproduced by changing the size and depth of the cells. [GB/T9851.5—2008,2.3]
Prime section prime section
The part of the screen that reflects the theme, such as images, text, logos, etc. [GB/T7705—2008,3.8]
Secondary section snb prime section
Other parts of the screen except the prime section. [GB/T7705—2008,3.9]
GB/T7707--2008
Technical requirements
The overprint error shall comply with the provisions of Table 1.
Printing materials
Biaxially stretched films
Non-biaxially stretched films
4.2 The requirements for solid printing shall comply with the provisions of Table 2. Item name
Density deviation of the same color
Color difference of the same color in the same batchwwW.bzxz.Net
Glossiness of ink layer
Bonding strength of overprint layer
CIELa'b
Table 1 Overprint error
Overprint position
Main position
Secondary position
Main position
Secondary position
Table 2 Solid printing requirements
Gs(60°)
Refers only to surface printing products. Products without glossiness requirements can cancel this indicator. Unit is meter
Overprint allowable error
Unit is meter
Indicator value
L≤50.00
bRefers only to the bonding strength between the ink layer and the film surface. Its indicator value is the bonding strength indicator value between the ink layer and the film surface except for gold and silver inks. 4.3 Appearance of printed surface
4.3.1 The finished product should be neat and tidy, without obvious ink stains, defects, knife lines, etc. 4.3.2 The printed text should be clear and complete, without defects or deformations, and the characters smaller than 7.5P (No. 6) should not affect the reading. Note: P—Point, 1P is approximately equal to 0.35mm. 4.3.3 The edge of the solid printed imprint should be smooth, uniform in color, and without obvious water marks. The transition of printing levels should be smooth, without obvious gradation jumps. 4.3.4
The dots should be clear and uniform, without obvious deformation and defects. 4.3.6
The printing color should meet the requirements of the printed sample. 5 Inspection method
5.1 Inspection conditions
5.1.1 Laboratory temperature and humidity: The temperature is 23℃±5℃, and the relative humidity is 60%±15%. 5.1.2 Sample pretreatment: under the conditions of 5.1.1, and placed in an environment without ultraviolet light for ≥8h. 5.1.3 Sample viewing light source: in accordance with the provisions of CY/T3. 5.2 Appearance
Place the sample under the sample viewing light source specified in 5.1.3 and identify it by visual inspection. 5.3 Overprint error
Place the test sample under the sample viewing light source specified in 5.1.3, and use a 20x reading magnifying glass with an accuracy of 0.01mm to measure the overprint error between any two colors in the main part and the secondary part of the test sample at 3 points, and take the maximum value as the overprint error of the main part and the secondary part of the test sample.
5.4 Density deviation of the same color
5.4.1 Instrument
Use a reflection densitometer that complies with ISO14981. 5.4.2 Instrument calibration and use method
Carry out in accordance with the provisions of GB/T18722.
5.4.3 Test steps
5.4.3.1 The backing of the sample should be white during the test. 5.4.3.2 Instrument calibration and use methods shall be in accordance with 5.4.2. GB/T7707—2008
5.4.3.3 For finished products with a format size of 135mm×195mm or less, measure one point at each of the four corners and the middle of the same color of the same sample; for finished products with a format size of 135mm×195mm or more, evenly increase the measurement by 5 points on the same sample. 5.4.4 Test results
5.4.4.1 The density deviation of the same color of each sample shall be calculated in accordance with formula (1). (DD,)2
Wherein:
D, homochromatic density deviation;
D—average value of homochromatic density of n times;
D,—homchromatic density measured for the ith time;
n——number of measurements.
5.4.4.2 Compare the average values of homochromatic density deviations of each color, and take the maximum value as the homochromatic density deviation of the sample. 5.5 Color difference of homochromatic colors in the same batch
5.5.1 Instrument
Use a spectrophotometer (colorimeter) that complies with ISO13655. 5.5.2 Instrument calibration and use method
Perform in accordance with the provisions of GB/T18722.
5.5.3 Inspection steps
·(12
Select one sample as the reference sample, and use a spectrophotometer to first measure its CIEL*αb value in the CIELαb' uniform color space, and then measure the color difference of the same color and the same part of the remaining samples with the reference sample. 5.5.4 Inspection results
Compare the color differences of the same color of the same batch of samples, and take the maximum value as the color difference of the same color of the same batch of the sample. 5.6 Glossiness of ink layer
5.6.1 Instrument
Use a gloss meter that complies with ISO15994. 5.6.2 Instrument calibration and use method
Perform in accordance with the provisions of ISO15994.
5.6.3 Inspection steps
5.6.3.1 Take a flat, wrinkle-free sample. 5.6.3. 2 Use a photometer to measure the surface of different color layers of the sample. Measure 3 points on the color layer with an area of <100cm2, and 5 points on the color layer with an area of >100cm.
5.6.3.3 When the difference in the gloss measurement results of each color of each sample is >5 gloss units, the number of measurement points should be doubled. 5.6.4 Test results
Calculate the average gloss of the same color at each point of the sample as the layer gloss of the sample of that color. 3
GB/T7707—2008
5.7 Ink layer bonding fastness
5.7.1 Sample requirements
5.7.1.1 Samples printed with ordinary gravure inks should be left for 8 hours before the ink layer bonding fastness test can be carried out. 5.7.1.2 Samples printed with gravure inks that need to be cured For samples printed with ink, the ink layer bonding strength test can be carried out after being left for 24 hours. 5.7.2 Test device
5.7.2.1 The selection of test tape shall comply with the provisions of A.1 in Appendix A. 5.7.2.2 The requirements for the tape roller are as specified in A.2.1 in Appendix A. 5.7.2.3 The disc peeling test machine is shown in Figure 1. The diameter of disc A is 170mm and the width is 55mm. The diameter of disc B is 65mm and the width is 55mm. The pressure between discs A and B is 100N. Ink layer
Adhesive tape
5.7.3 Test steps
Direction of movement
Figure 1 Disc peeling test machine
5.7.3.1 Stick the tape on the ink printed surface of the sample and roll it back and forth on the tape roller. Press three times to make the required sample part completely adhered, and place the sample with the tape adhered for 5min10min. 5.7.3.2 Clamp one end of the sample on disk A, and fix the exposed tape on disk B (see Figure 1). 5.7.3.3 After turning on the machine, disk A rotates at a speed of 0.6m/s~1.0m/s to peel off the tape. 5.7.3.4 Remove the sample, cover the peeled part with a 20mm wide translucent millimeter grid paper, and count the number of grids occupied by the ink layer and the number of grids occupied by the peeled ink layer respectively.
5.7.4 Test results
The ink layer bonding strength is calculated according to formula (2).
Where:
Valley layer bonding strength;
Number of grids of an ink layer;
A. Number of grids of the peeled ink layer.
6 Inspection rules
6.1 A group of products of the same variety, specification and production cycle with basically the same production conditions is called a batch. (2)
6.2 Sampling inspection shall be carried out in accordance with the inspection sampling plan of GB/T2828.1. The sample unit of film is roll, and the sample unit of bag is piece. The minimum number of samples per batch is generally not less than 3 rolls for film and not less than 5 pieces for bags. 4
GB/T7707—2008
6.3 Determination of unqualified products: Each product (film or bag) shall be inspected in accordance with the provisions of this standard. If one or more technical indicators do not meet the requirements, the product shall be unqualified. 6.4 Determination of unqualified batches: Each batch of products (film or bag) shall be inspected in accordance with the provisions of this standard. If one or more products are unqualified, double sampling shall be carried out for re-inspection. If one or more products are still unqualified, the batch shall be unqualified. 7 Marking, packaging, transportation, storage
7.1 Marking
The product packaging box should be accompanied by a product inspection certificate, and indicate the user unit, product name, variety and specification, quantity (film in meters, bags in pieces), quality, batch number, manufacturer name, production date, inspector code, etc. 7.2 Packaging
Film and bag products should be packed in corrugated boxes lined with plastic film (film with simple core shockproof pad core) or paper, or can be packed according to the contract requirements of the supply and demand parties.
7.3 Transportation
During transportation, loading and unloading should be done gently, collision and contact with sharp objects should be avoided, heavy pressure should be avoided, and sun protection, rain protection, and heat protection should be prevented. The packaging should be intact and the product should not be contaminated or damaged. 7.4 Storage
The product should be stored in a clean, dry, ventilated warehouse with moderate temperature. It should be kept away from heat sources and should be at least 1m away from the heat source. The product should not be piled too high to prevent heavy pressure. The storage period of the product is generally no more than 6 months from the date of production. GB/T7707—2008
A.1 Basic requirements for tapes
A.1.1 Width
A.1.2 Adhesion
A.1.3 Tape substrate
A.1.4 Adhesive
A.1.5 Solvent
Method for determining the adhesion of tapes
A.2.1 Tape rolling machine
Appendix A
(Normative Appendix)
Tape for ink layer fastness test
2.91N/19mm~3.33N/19mm
Synthetic acrylic adhesive
Aromatic hydrocarbons
A.2.1.1 The pressure roller is a rubber-covered metal roller with a diameter of 84mm±1mm and a width of 45mm. A.2.1.2 Rubber hardness (Shore A type) is 60~80, thickness is 6mm. Roller load 20N0.5N.
Rolling speed 0.3m/min.
A.2.2 Tensile testing machine
The tensile testing machine should be able to automatically record the peeling load and have a drawing output. A.2.3 Test method
A.2.3.1 The test room temperature is 25℃±2℃, and the relative humidity is 60%±5%. A.2.3.2 The material to be adhered by the tape should be placed under the conditions of A.2.3.1 for more than 2h. A.2.3.3 Peel off the tape, stick it to the material to be adhered, roll it back and forth on the tape roller three times, and then test it after leaving it for 5min. The tensile testing machine continuously peels at a speed of 0.3m/min, and the adhesion is calculated according to the planimeter method in 7.2 of GB/T2792-1998.
Each roll is measured three times, and the average value is the adhesive strength of the tape. A.2.3.5
References
Printing Technology Terminology
[1]GB/T9851.1-2008
Part 1: Basic Terminology
GB/T9851.5-2008 Printing Technology Terminology[2]
Part 5: Terminology of intaglio printing,
8 Lithographic decorative printed matter.
[3]GB/T7705—2008
GB/T7707—2008
GB/T7707-2008
National Standard of the People's Republic of China
Intaglio decorative printed matter
GB/T7707-—2008
Published and distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal Code: 100045
Website Address: spc.net.cn
Tel: 6852394668517548
Printed by Qinhuangdao Printing Factory of China Standard Press Distributed by Xinhua Bookstores in various places
Format: 880×12301/16
Printing sheet: 0.75 Word count: 14,000 words
First edition: October 2008 First printing: October 2008*
Book number: 155066·1-34379
If there is any printing error, the publishing center of our company will replace it. Copyright infringement will be investigated
Report telephone: (010) 685335332 Instrument calibration and use method
Perform according to the provisions of ISO15994.
5.6.3 Inspection steps
5.6.3.1 Take a flat, wrinkle-free sample. 5.6.3.2 Use a photometer to measure the surface of different color layers of the sample. Measure 3 points on the color layer with an area of <100cm2 and 5 points on the color layer with an area of >100cm.
5.6.3.3 When the difference in the glossiness measurement results of each color of each sample is >5 glossiness units, the number of measurement points should be doubled. 5.6.4 Inspection results
Calculate the average glossiness of the same color at each point of the sample as the glossiness of the layer of that color of that sample. 3
GB/T7707—2008
5.7 Ink layer bonding strength
5.7.1 Sample requirements
5.7.1.1 For samples printed with ordinary gravure ink, the ink layer bonding strength test can be carried out after being left for 8 hours. 5.7.1.2 For samples printed with gravure ink that needs to be cured, the ink layer bonding strength test can be carried out after being left for 24 hours. 5.7.2 Inspection device
5.7.2.1 The selection of the test tape shall comply with the provisions of A.1 in Appendix A. 5.7.2.2 The requirements for the tape roller are as specified in A.2.1 in Appendix A. 5.7.2.3 The disc peeling test machine is shown in Figure 1. The diameter of disc A is 170 mm and the width is 55 mm. The diameter of disc B is 65 mm and the width is 55 mm. The pressure between discs A and B is 100 N. Ink layer
Adhesive tape
5.7.3 Inspection steps
Motion direction
Figure 1 Disc peeling test machine
5.7.3.1 Stick the tape on the ink printed surface of the sample, and roll it back and forth on the tape roller three times to make the required sample part completely stick, and place the sample with the tape stuck for 5min10min. 5.7.3.2 Clamp one end of the sample on the A disk, and fix the exposed tape on the B disk (see Figure 1). 5.7.3.3 After turning on the machine, the A disk rotates at a speed of 0.6m/s~1.0m/s to peel off the tape. 5.7.3.4 Remove the sample, cover the peeled part with a 20mm wide translucent millimeter grid paper, and count the number of grids occupied by the ink layer and the number of grids occupied by the peeled ink layer respectively.
5.7.4 Test results
The ink layer bonding strength is calculated according to formula (2).
Where:
B. Layer bonding strength;
Number of grids of an ink layer;
A. Number of grids of the ink layer to be peeled off.
6 Test rules
6.1 A group of products of the same variety, specification and production cycle with basically the same production conditions is a batch. (2)
6.2 Sampling inspection is carried out in accordance with the inspection sampling plan of GB/T2828.1. The sample unit of the film is roll, and the sample unit of the bag is piece. The minimum sample quantity per batch is generally not less than 3 rolls for film and not less than 5 pieces for bags. 4
GB/T7707—2008
6.3 Determination of unqualified products: Each product (film or bag) shall be inspected according to the provisions of this standard. If one or more technical indicators do not meet the requirements, the product shall be unqualified. 6.4 Determination of unqualified batches: Each batch of products (film or bag) shall be inspected according to the provisions of this standard. If one or more products are unqualified, double sampling and re-inspection shall be carried out. If there are still one or more products that are unqualified, the batch shall be unqualified. 7 Marking, packaging, transportation, storage
7.1 Marking
The product packaging box shall be accompanied by a product inspection certificate, and shall indicate the user unit, product name, variety and specification, quantity (film in meters, bags in pieces), quality, batch number, manufacturer name, production date, inspector code, etc. 7.2 Packaging
Film and bag products should be packed in corrugated boxes lined with plastic film (film plus simple core shockproof pad core) or paper, or packed according to the contract requirements of the supply and demand parties.
7.3 Transportation
During transportation, the products should be loaded and unloaded gently, and collisions and contact with sharp objects should be avoided, and heavy pressure should be avoided. They should be protected from sunlight, rain, and heat. The packaging should be intact and the products should not be contaminated or damaged. 7.4 Storage
The products should be stored in a clean, dry, ventilated warehouse with moderate temperature. They should be kept away from heat sources and should be at least 1m away from the heat sources. They should not be stacked too high to prevent heavy pressure. The storage period of the product is generally no more than 6 months from the date of production. GB/T7707—2008
A.1 Basic requirements for tapes
A.1.1 Width
A.1.2 Adhesion
A.1.3 Tape substrate
A.1.4 Adhesive
A.1.5 Solvent
Method for determining the adhesion of tapes
A.2.1 Tape rolling machine
Appendix A
(Normative Appendix)
Tape for ink layer fastness test
2.91N/19mm~3.33N/19mm
Synthetic acrylic adhesive
Aromatic hydrocarbons
A.2.1.1 The pressure roller is a rubber-covered metal roller with a diameter of 84mm±1mm and a width of 45mm. A.2.1.2 Rubber hardness (Shore A type) is 60~80, thickness is 6mm. Roller load 20N0.5N.
Rolling speed 0.3m/min.
A.2.2 Tensile testing machine
The tensile testing machine should be able to automatically record the peeling load and have a drawing output. A.2.3 Test method
A.2.3.1 The test room temperature is 25℃±2℃, and the relative humidity is 60%±5%. A.2.3.2 The material to be adhered by the tape should be placed under the conditions of A.2.3.1 for more than 2h. A.2.3.3 Peel off the tape, stick it to the material to be adhered, roll it back and forth on the tape roller three times, and then test it after leaving it for 5min. The tensile testing machine continuously peels at a speed of 0.3m/min, and the adhesion is calculated according to the planimeter method in 7.2 of GB/T2792-1998.
Each roll is measured three times, and the average value is the adhesive strength of the tape. A.2.3.5
References
Printing Technology Terminology
[1]GB/T9851.1-2008
Part 1: Basic Terminology
GB/T9851.5-2008 Printing Technology Terminology[2]
Part 5: Terminology of intaglio printing,
8 Lithographic decorative printed matter.
[3]GB/T7705—2008
GB/T7707—2008
GB/T7707-2008
National Standard of the People's Republic of China
Intaglio decorative printed matter
GB/T7707-—2008
Published and distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal Code: 100045
Website Address: spc.net.cn
Tel: 6852394668517548
Printed by Qinhuangdao Printing Factory of China Standard Press Distributed by Xinhua Bookstores in various places
Format: 880×12301/16
Printing sheet: 0.75 Word count: 14,000 words
First edition: October 2008 First printing: October 2008*
Book number: 155066·1-34379
If there is any printing error, the publishing center of our company will replace it. Copyright infringement will be investigated
Report telephone: (010) 685335332 Instrument calibration and use method
Perform according to the provisions of ISO15994.
5.6.3 Inspection steps
5.6.3.1 Take a flat, wrinkle-free sample. 5.6.3.2 Use a photometer to measure the surface of different color layers of the sample. Measure 3 points on the color layer with an area of <100cm2 and 5 points on the color layer with an area of >100cm.
5.6.3.3 When the difference in the glossiness measurement results of each color of each sample is >5 glossiness units, the number of measurement points should be doubled. 5.6.4 Inspection results
Calculate the average glossiness of the same color at each point of the sample as the glossiness of the layer of that color of that sample. 3
GB/T7707—2008
5.7 Ink layer bonding strength
5.7.1 Sample requirements
5.7.1.1 For samples printed with ordinary gravure ink, the ink layer bonding strength test can be carried out after being left for 8 hours. 5.7.1.2 For samples printed with gravure ink that needs to be cured, the ink layer bonding strength test can be carried out after being left for 24 hours. 5.7.2 Inspection device
5.7.2.1 The selection of the test tape shall comply with the provisions of A.1 in Appendix A. 5.7.2.2 The requirements for the tape roller are as specified in A.2.1 in Appendix A. 5.7.2.3 The disc peeling test machine is shown in Figure 1. The diameter of disc A is 170 mm and the width is 55 mm. The diameter of disc B is 65 mm and the width is 55 mm. The pressure between discs A and B is 100 N. Ink layer
Adhesive tape
5.7.3 Inspection steps
Motion direction
Figure 1 Disc peeling test machine
5.7.3.1 Stick the tape on the ink printed surface of the sample, and roll it back and forth on the tape roller three times to make the required sample part completely stick, and place the sample with the tape stuck for 5min10min. 5.7.3.2 Clamp one end of the sample on the A disk, and fix the exposed tape on the B disk (see Figure 1). 5.7.3.3 After turning on the machine, the A disk rotates at a speed of 0.6m/s~1.0m/s to peel off the tape. 5.7.3.4 Remove the sample, cover the peeled part with a 20mm wide translucent millimeter grid paper, and count the number of grids occupied by the ink layer and the number of grids occupied by the peeled ink layer respectively.
5.7.4 Test results
The ink layer bonding strength is calculated according to formula (2).
Where:
B. Layer bonding strength;
Number of grids of an ink layer;
A. Number of grids of the ink layer to be peeled off.
6 Test rules
6.1 A group of products of the same variety, specification and production cycle with basically the same production conditions is a batch. (2)
6.2 Sampling inspection is carried out in accordance with the inspection sampling plan of GB/T2828.1. The sample unit of the film is roll, and the sample unit of the bag is piece. The minimum sample quantity per batch is generally not less than 3 rolls for film and not less than 5 pieces for bags. 4
GB/T7707—2008
6.3 Determination of unqualified products: Each product (film or bag) shall be inspected according to the provisions of this standard. If one or more technical indicators do not meet the requirements, the product shall be unqualified. 6.4 Determination of unqualified batches: Each batch of products (film or bag) shall be inspected according to the provisions of this standard. If one or more products are unqualified, double sampling and re-inspection shall be carried out. If there are still one or more products that are unqualified, the batch shall be unqualified. 7 Marking, packaging, transportation, storage
7.1 Marking
The product packaging box shall be accompanied by a product inspection certificate, and shall indicate the user unit, product name, variety and specification, quantity (film in meters, bags in pieces), quality, batch number, manufacturer name, production date, inspector code, etc. 7.2 Packaging
Film and bag products should be packed in corrugated boxes lined with plastic film (film plus simple core shockproof pad core) or paper, or packed according to the contract requirements of the supply and demand parties.
7.3 Transportation
During transportation, the products should be loaded and unloaded gently, and collisions and contact with sharp objects should be avoided, and heavy pressure should be avoided. They should be protected from sunlight, rain, and heat. The packaging should be intact and the products should not be contaminated or damaged. 7.4 Storage
The products should be stored in a clean, dry, ventilated warehouse with moderate temperature. They should be kept away from heat sources and should be at least 1m away from the heat sources. They should not be stacked too high to prevent heavy pressure. The storage period of the product is generally no more than 6 months from the date of production. GB/T7707—2008
A.1 Basic requirements for tapes
A.1.1 Width
A.1.2 Adhesion
A.1.3 Tape substrate
A.1.4 Adhesive
A.1.5 Solvent
Method for determining the adhesion of tapes
A.2.1 Tape rolling machine
Appendix A
(Normative Appendix)
Tape for ink layer fastness test
2.91N/19mm~3.33N/19mm
Synthetic acrylic adhesive
Aromatic hydrocarbons
A.2.1.1 The pressure roller is a rubber-covered metal roller with a diameter of 84mm±1mm and a width of 45mm. A.2.1.2 Rubber hardness (Shore A type) is 60~80, thickness is 6mm. Roller load 20N0.5N.
Rolling speed 0.3m/min.
A.2.2 Tensile testing machine
The tensile testing machine should be able to automatically record the peeling load and have a drawing output. A.2.3 Test method
A.2.3.1 The test room temperature is 25℃±2℃, and the relative humidity is 60%±5%. A.2.3.2 The material to be adhered by the tape should be placed under the conditions of A.2.3.1 for more than 2h. A.2.3.3 Peel off the tape, stick it to the material to be adhered, roll it back and forth on the tape roller three times, and then test it after leaving it for 5min. The tensile testing machine continuously peels at a speed of 0.3m/min, and the adhesion is calculated according to the planimeter method in 7.2 of GB/T2792-1998.
Each roll is measured three times, and the average value is the adhesive strength of the tape. A.2.3.5
References
Printing Technology Terminology
[1]GB/T9851.1-2008
Part 1: Basic Terminology
GB/T9851.5-2008 Printing Technology Terminology[2]
Part 5: Terminology of intaglio printing,
8 Lithographic decorative printed matter.
[3]GB/T7705—2008
GB/T7707—2008
GB/T7707-2008
National Standard of the People's Republic of China
Intaglio decorative printed matter
GB/T7707-—2008
Published and distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal Code: 100045
Website Address: spc.net.cn
Tel: 6852394668517548
Printed by Qinhuangdao Printing Factory of China Standard Press Distributed by Xinhua Bookstores in various places
Format: 880×12301/16
Printing sheet: 0.75 Word count: 14,000 words
First edition: October 2008 First printing: October 2008*
Book number: 155066·1-34379
If there is any printing error, the publishing center of our company will replace it. Copyright infringement will be investigated
Report telephone: (010) 685335331 The selection of the test tape shall comply with the provisions of A.1 in Appendix A. 5.7.2.2 The requirements of the tape roller machine shall be as specified in A.2.1 in Appendix A. 5.7.2.3 The disc peeling test machine is shown in Figure 1. The diameter of disc A is 170 mm and the width is 55 mm. The diameter of disc B is 65 mm and the width is 55 mm. The pressure between discs A and B is 100 N. Ink layer
Adhesive tape
5.7.3 Inspection steps
Direction of movement
Figure 1 Disc peeling test machine
5.7.3.1 Stick the tape on the ink printed surface of the sample, and roll it back and forth on the tape roller three times to make the required sample part completely stick, and place the sample with the tape stuck for 5min10min. 5.7.3.2 Clamp one end of the sample on disc A, and fix the exposed tape on disc B (see Figure 1). 5.7.3.3 After starting the machine, rotate the A disk at a speed of 0.6m/s~1.0m/s to peel off the tape. 5.7.3.4 Remove the sample and cover the peeled part with a 20mm wide translucent millimeter grid paper. Count the number of grids occupied by the ink layer and the number of grids occupied by the peeled ink layer respectively.
5.7.4 Test results
The ink layer bonding strength is calculated according to formula (2).
Where:
B. The bonding strength of the ink layer;
A. The number of grids of the ink layer;
A. The number of grids of the peeled ink layer.
6 Test rules
6.1 A group of products of the same variety, same specification and same production cycle with basically the same production conditions is considered a batch. (2)
6.2 Sampling test shall be carried out in accordance with the test sampling plan specified in GB/T2828.1. The sample unit for film is roll, and the sample unit for bag is piece. The minimum sample quantity for each batch is generally not less than 3 rolls for film and not less than 5 pieces for bags. 4
GB/T7707—2008
6.3 Determination of unqualified products: Each product (film or bag) shall be inspected according to the provisions of this standard. If one or more technical indicators do not meet the requirements, the product shall be unqualified. 6.4 Determination of unqualified batches: Each batch of products (film or bag) shall be inspected according to the provisions of this standard. If one or more products are unqualified, double sampling shall be conducted for re-inspection. If there are still one or more unqualified products, the batch shall be unqualified. 7 Marking, packaging, transportation, storage
7.1 Marking
The product packaging box should be accompanied by a product inspection certificate, and indicate the user unit, product name, variety and specification, quantity (film in meters, bags in pieces), quality, batch number, manufacturer name, production date, inspector code, etc. 7.2 Packaging
Film and bag products should be packed in corrugated boxes lined with plastic film (film with simple core shockproof pad core) or paper, or can be packed according to the contract requirements of the supply and demand parties.
7.3 Transportation
During transportation, loading and unloading should be done gently, collision and contact with sharp objects should be avoided, heavy pressure should be avoided, and sun protection, rain protection, and heat protection should be prevented. The packaging should be intact and the product should not be contaminated or damaged. 7.4 Storage
The product should be stored in a clean, dry, ventilated warehouse with moderate temperature. It should be kept away from heat sources and should be at least 1m away from the heat source. The product should not be piled too high to prevent heavy pressure. The product storage period is generally no more than 6 months from the date of production. GB/T7707—2008
A.1 Basic requirements for tapes
A.1.1 Width
A.1.2 Adhesion
A.1.3 Tape substrate
A.1.4 Adhesive
A.1.5 Solvent
Method for determining the adhesion of tapes
A.2.1 Tape rolling machine
Appendix A
(Normative Appendix)
Tape for ink layer fastness test
2.91N/19mm~3.33N/19mm
Synthetic acrylic adhesive
Aromatic hydrocarbons
A.2.1.1 The pressure roller is a rubber-covered metal roller with a diameter of 84mm±1mm and a width of 45mm. A.2.1.2 Rubber hardness (Shore A type) is 60~80, thickness is 6mm. Roller load 20N0.5N.
Rolling speed 0.3m/min.
A.2.2 Tensile testing machine
The tensile testing machine should be able to automatically record the peeling load and have a drawing output. A.2.3 Test method
A.2.3.1 The test room temperature is 25℃±2℃, and the relative humidity is 60%±5%. A.2.3.2 The material to be adhered by the tape should be placed under the conditions of A.2.3.1 for more than 2h. A.2.3.3 Peel off the tape, stick it to the material to be adhered, roll it back and forth on the tape roller three times, and then test it after leaving it for 5min. The tensile testing machine continuously peels at a speed of 0.3m/min, and the adhesion is calculated according to the planimeter method in 7.2 of GB/T2792-1998.
Each roll is measured three times, and the average value is the adhesive strength of the tape. A.2.3.5
References
Printing Technology Terminology
[1]GB/T9851.1-2008
Part 1: Basic Terminology
GB/T9851.5-2008 Printing Technology Terminology[2]
Part 5: Terminology of intaglio printing,
8 Lithographic decorative printed matter.
[3]GB/T7705—2008
GB/T7707—2008
GB/T7707-2008
National Standard of the People's Republic of China
Intaglio decorative printed matter
GB/T7707-—2008
Published and distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal Code: 100045
Website Address: spc.net.cn
Tel: 6852394668517548
Printed by Qinhuangdao Printing Factory of China Standard Press Distributed by Xinhua Bookstores in various places
Format: 880×12301/16
Printing sheet: 0.75 Word count: 14,000 words
First edition: October 2008 First printing: October 2008*
Book number: 155066·1-34379
If there is any printing error, the publishing center of our company will replace it. Copyright infringement will be investigated
Report telephone: (010) 685335331 The selection of the test tape shall comply with the provisions of A.1 in Appendix A. 5.7.2.2 The requirements of the tape roller machine shall be as specified in A.2.1 in Appendix A. 5.7.2.3 The disc peeling test machine is shown in Figure 1. The diameter of disc A is 170 mm and the width is 55 mm. The diameter of disc B is 65 mm and the width is 55 mm. The pressure between discs A and B is 100 N. Ink layer
Adhesive tape
5.7.3 Inspection steps
Direction of movement
Figure 1 Disc peeling test machine
5.7.3.1 Stick the tape on the ink printed surface of the sample, and roll it back and forth on the tape roller three times to make the required sample part completely stick, and place the sample with the tape stuck for 5min10min. 5.7.3.2 Clamp one end of the sample on disc A, and fix the exposed tape on disc B (see Figure 1). 5.7.3.3 After starting the machine, rotate the A disk at a speed of 0.6m/s~1.0m/s to peel off the tape. 5.7.3.4 Remove the sample and cover the peeled part with a 20mm wide translucent millimeter grid paper. Count the number of grids occupied by the ink layer and the number of grids occupied by the peeled ink layer respectively.
5.7.4 Test results
The ink layer bonding strength is calculated according to formula (2).
Where:
B. The bonding strength of the ink layer;
A. The number of grids of the ink layer;
A. The number of grids of the peeled ink layer.
6 Test rules
6.1 A group of products of the same variety, same specification and same production cycle with basically the same production conditions is considered a batch. (2)
6.2 Sampling test shall be carried out in accordance with the test sampling plan specified in GB/T2828.1. The sample unit for film is roll, and the sample unit for bag is piece. The minimum sample quantity for each batch is generally not less than 3 rolls for film and not less than 5 pieces for bags. 4
GB/T7707—2008
6.3 Determination of unqualified products: Each product (film or bag) shall be inspected according to the provisions of this standard. If one or more technical indicators do not meet the requirements, the product shall be unqualified. 6.4 Determination of unqualified batches: Each batch of products (film or bag) shall be inspected according to the provisions of this standard. If one or more products are unqualified, double sampling shall be conducted for re-inspection. If there are still one or more unqualified products, the batch shall be unqualified. 7 Marking, packaging, transportation, storage
7.1 Marking
The product packaging box should be accompanied by a product inspection certificate, and indicate the user unit, product name, variety and specification, quantity (film in meters, bags in pieces), quality, batch number, manufacturer name, production date, inspector code, etc. 7.2 Packaging
Film and bag products should be packed in corrugated boxes lined with plastic film (film with simple core shockproof pad core) or paper, or can be packed according to the contract requirements of the supply and demand parties.
7.3 Transportation
During transportation, loading and unloading should be done gently, collision and contact with sharp objects should be avoided, heavy pressure should be avoided, and sun protection, rain protection, and heat protection should be prevented. The packaging should be intact and the product should not be contaminated or damaged. 7.4 Storage
The product should be stored in a clean, dry, ventilated warehouse with moderate temperature. It should be kept away from heat sources and should be at least 1m away from the heat source. The product should not be piled too high to prevent heavy pressure. The storage period of the product is generally no more than 6 months from the date of production. GB/T7707—2008
A.1 Basic requirements for tapes
A.1.1 Width
A.1.2 Adhesion
A.1.3 Tape substrate
A.1.4 Adhesive
A.1.5 Solvent
Method for determining the adhesion of tapes
A.2.1 Tape rolling machine
Appendix A
(Normative Appendix)
Tape for ink layer fastness test
2.91N/19mm~3.33N/19mm
Synthetic acrylic adhesive
Aromatic hydrocarbons
A.2.1.1 The pressure roller is a rubber-covered metal roller with a diameter of 84mm±1mm and a width of 45mm. A.2.1.2 Rubber hardness (Shore A type) is 60~80, thickness is 6mm. Roller load 20N0.5N.
Rolling speed 0.3m/min.
A.2.2 Tensile testing machine
The tensile testing machine should be able to automatically record the peeling load and have a drawing output. A.2.3 Test method
A.2.3.1 The test room temperature is 25℃±2℃, and the relative humidity is 60%±5%. A.2.3.2 The material to be adhered by the tape should be placed under the conditions of A.2.3.1 for more than 2h. A.2.3.3 Peel off the tape, stick it to the material to be adhered, roll it back and forth on the tape roller three times, and then test it after leaving it for 5min. The tensile testing machine continuously peels at a speed of 0.3m/min, and the adhesion is calculated according to the planimeter method in 7.2 of GB/T2792-1998.
Each roll is measured three times, and the average value is the adhesive strength of the tape. A.2.3.5
References
Printing Technology Terminology
[1]GB/T9851.1-2008
Part 1: Basic Terminology
GB/T9851.5-2008 Printing Technology Terminology[2]
Part 5: Terminology of intaglio printing,
8 Lithographic decorative printed matter.
[3]GB/T7705—2008
GB/T7707—2008
GB/T7707-2008
National Standard of the People's Republic of China
Intaglio decorative printed matter
GB/T7707-—2008
Published and distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal Code: 100045
Website Address: spc.net.cn
Tel: 6852394668517548
Printed by Qinhuangdao Printing Factory of China Standard Press Distributed by Xinhua Bookstores in various places
Format: 880×12301/16
Printing sheet: 0.75 Word count: 14,000 words
First edition: October 2008 First printing: October 2008*
Book number: 155066·1-34379
If there is any printing error, the publishing center of our company will replace it. Copyright infringement will be investigated
Report telephone: (010) 685335334 Determination of unqualified batches: Each batch of products (films or bags) shall be inspected in accordance with the provisions of this standard. If one or more products are unqualified, double sampling shall be conducted for re-inspection. If there are still one or more unqualified products, the batch shall be unqualified. 7 Marking, packaging, transportation, storage
7.1 Marking
The product packaging box shall be accompanied by a product inspection certificate, and shall indicate the user unit, product name, variety and specification, quantity (film in meters, bag in pieces), quality, batch number, manufacturer name, production date, inspector code, etc. 7.2 Packaging
Film and bag products shall be packaged in corrugated boxes lined with plastic film (film with simple core and shockproof pad cover core) or paper, or they may be packaged according to the contract requirements between the supply and demand parties.
7.3 Transportation
During transportation, the products should be loaded and unloaded with care, and collisions and contact with sharp objects should be avoided, and heavy pressure should be avoided. They should be protected from the sun, rain, and heat. The packaging should be intact and the products should not be contaminated or damaged. 7.4 Storage
The products should be stored in a clean, dry, ventilated warehouse with moderate temperature. They should be kept away from heat sources and should be at least 1m away from heat sources. They should not be stacked too high to prevent heavy pressure. The product storage period is generally no more than 6 months from the date of production. GB/T7707—2008
A.1 Basic requirements for tapes
A.1.1 Width
A.1.2 Adhesion
A.1.3 Tape substrate
A.1.4 Adhesive
A.1.5 Solvent
Method for determining the adhesion of tapes
A.2.1 Tape rolling machine
Appendix A
(Normative Appendix)
Tape for ink layer fastness test
2.91N/19mm~3.33N/19mm
Synthetic acrylic adhesive
Aromatic hydrocarbons
A.2.1.1 The pressure roller is a rubber-covered metal roller with a diameter of 84mm±1mm and a width of 45mm. A.2.1.2 Rubber hardness (Shore A type) is 60~80, thickness is 6mm. Roller load 20N0.5N.
Rolling speed 0.3m/min.
A.2.2 Tensile testing machine
The tensile testing machine should be able to automatically record the peeling load and have a drawing output. A.2.3 Test method
A.2.3.1 The test room temperature is 25℃±2℃, and the relative humidity is 60%±5%. A.2.3.2 The material to be adhered by the tape should be placed under the conditions of A.2.3.1 for more than 2h. A.2.3.3 Peel off the tape, stick it to the material to be adhered, roll it back and forth on the tape roller three times, and then test it after leaving it for 5min. The tensile testing machine continuously peels at a speed of 0.3m/min, and the adhesion is calculated according to the planimeter method in 7.2 of GB/T2792-1998.
Each roll is measured three times, and the average value is the adhesive strength of the tape. A.2.3.5
References
Printing Technology Terminology
[1]GB/T9851.1-2008
Part 1: Basic Terminology
GB/T9851.5-2008 Printing Technology Terminology[2]
Part 5: Terminology of intaglio printing,
8 Lithographic decorative printed matter.
[3]GB/T7705—2008
GB/T7707—2008
GB/T7707-2008
National Standard of the People's Republic of China
Intaglio decorative printed matter
GB/T7707-—2008
Published and distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal Code: 100045
Website Address: spc.net.cn
Tel: 6852394668517548
Printed by Qinhuangdao Printing Factory of China Standard Press Distributed by Xinhua Bookstores in various places
Format: 880×12301/16
Printing sheet: 0.75 Word count: 14,000 words
First edition: October 2008 First printing: October 2008*
Book number: 155066·1-34379
If there is any printing error, the publishing center of our company will replace it. Copyright infringement will be investigated
Report telephone: (010) 685335334 Determination of unqualified batches: Each batch of products (films or bags) shall be inspected in accordance with the provisions of this standard. If one or more products are unqualified, double sampling shall be conducted for re-inspection. If there are still one or more unqualified products, the batch shall be unqualified. 7 Marking, packaging, transportation, storage
7.1 Marking
The product packaging box shall be accompanied by a product inspection certificate, and shall indicate the user unit, product name, variety and specification, quantity (film in meters, bag in pieces), quality, batch number, manufacturer name, production date, inspector code, etc. 7.2 Packaging
Film and bag products shall be packaged in corrugated boxes lined with plastic film (film with simple core and shockproof pad cover core) or paper, or they may be packaged according to the contract requirements between the supply and demand parties.
7.3 Transportation
During transportation, the products should be loaded and unloaded with care, and collisions and contact with sharp objects should be avoided, and heavy pressure should be avoided. They should be protected from the sun, rain, and heat. The packaging should be intact and the products should not be contaminated or damaged. 7.4 Storage
The products should be stored in a clean, dry, ventilated warehouse with moderate temperature. They should be kept away from heat sources and should be at least 1m away from heat sources. They should not be stacked too high to prevent heavy pressure. The product storage period is generally no more than 6 months from the date of production. GB/T7707—2008
A.1 Basic requirements for tapes
A.1.1 Width
A.1.2 Adhesion
A.1.3 Tape substrate
A.1.4 Adhesive
A.1.5 Solvent
Method for determining the adhesion of tapes
A.2.1 Tape rolling machine
Appendix A
(Normative Appendix)
Tape for ink layer fastness test
2.91N/19mm~3.33N/19mm
Synthetic acrylic adhesive
Aromatic hydrocarbons
A.2.1.1 The pressure roller is a rubber-covered metal roller with a diameter of 84mm±1mm and a width of 45mm. A.2.1.2 Rubber hardness (Shore A type) is 60~80, thickness is 6mm. Roller load 20N0.5N.
Rolling speed 0.3m/min.
A.2.2 Tensile testing machine
The tensile testing machine should be able to automatically record the peeling load and have a drawing output. A.2.3 Test method
A.2.3.1 The test room temperature is 25℃±2℃, and the relative humidity is 60%±5%. A.2.3.2 The material to be adhered by the tape should be placed under the conditions of A.2.3.1 for more than 2h. A.2.3.3 Peel off the tape, stick it to the material to be adhered, roll it back and forth on the tape roller three times, and then test it after leaving it for 5min. The tensile testing machine continuously peels at a speed of 0.3m/min, and the adhesion is calculated according to the planimeter method in 7.2 of GB/T2792-1998.
Each roll is measured three times, and the average value is the adhesive strength of the tape. A.2.3.5
References
Printing Technology Terminology
[1]GB/T9851.1-2008
Part 1: Basic Terminology
GB/T9851.5-2008 Printing Technology Terminology[2]
Part 5: Terminology of intaglio printing,
8 Lithographic decorative printed matter.
[3]GB/T7705—2008
GB/T7707—2008
GB/T7707-2008
National Standard of the People's Republic of China
Intaglio decorative printed matter
GB/T7707-—2008
Published and distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal Code: 100045
Website Address: spc.net.cn
Tel: 6852394668517548
Printed by Qinhuangdao Printing Factory of China Standard Press Distributed by Xinhua Bookstores in various places
Format: 880×12301/16
Printing sheet: 0.75 Word count: 14,000 words
First edition: October 2008 First printing: October 2008*
Book number: 155066·1-34379
If there is any printing error, the publishing center of our company will replace it. Copyright infringement will be investigated
Report telephone: (010) 68533533
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.