This standard specifies the general requirements, safety requirements and installation technical conditions for chicken farming machinery and equipment. This standard applies to the installation and use of chicken farming machinery and equipment (including waterers, traction-type floor scraper manure cleaners, incubators, hatchers, chain and spiral spring feeders, laying hen cages and cage racks, electric brooding umbrellas and other major mechanical equipment, hereinafter referred to as mechanical equipment). Other poultry machinery can be used as a reference. NY/T 649-2002 Technical Conditions for Installation of Chicken Farming Machinery and Equipment NY/T649-2002 Standard Download Decompression Password: www.bzxz.net

IC8 65.040.1C
Agricultural Industry Standard of the People's Republic of China
NY/T 6492002
Technical specificalion of installationalian for rhicken breeding equipment
Technical specificalion of installationalian for rhicken breeding equipment2002-12-30 Issued
2003-03-01 Implementation
Issued by the Ministry of Agriculture of the People's Republic of China
643-7002
Rhicken breeding equipment includes six main types of equipment: live block water dispenser, traction type scraper consumption machine, cutter (mountain maintenance machine), chain type spiral spring type feeder, laying hen cage type cage frame, and heat breeding maintenance umbrella. This standard is issued by the Agricultural Post Agricultural Mechanization Management Department. This standard is regulated by the Agricultural Mechanization Branch of the Agricultural Machinery Committee. This standard is approved by: Agricultural Machinery Testing and Identification Center of the Ministry of Agriculture, Agricultural Machinery Testing and Identification Promotion Center, Shengdao Huabo Livestock Technology Co., Ltd., the main contributors of this standard are: Lian Wenwei, Lu Junjie, Hao Wenlu, Xiang Jiahong, Wai Gaobo.1 Standard
Technical conditions for the installation of chicken machinery and equipment bzxZ.net
This standard specifies the requirements, safety requirements and installation techniques of chicken machinery and equipment, NY/T6492002
This standard is applicable to the installation and use of chicken machinery and equipment (including drinking fountains, ground scrapers, hatchers, chain and screw buckets, chicken cages and other main equipment, see the following brief introduction).
2 Reference standards
The following clauses shall become the clauses of this standard after being filtered through this standard: For any referenced document of a certain period, if its format is modified (excluding the abandonment of errors) or revised, it shall not be applicable to this standard. Before that, the parties who have reached an agreement based on this standard are encouraged to study whether the latest version of this document can be used. For referenced documents without undated dates, the latest edition shall apply to this standard. G11:02:.1-1ss7
Rated daily load of 52 and below ethyl chloride sieve cable: General requirements GB10395.12CC1 Agricultural and forestry tractors - Safety technical requirements - Part 1: General - Forestry tractors, horticultural power machinery, general principles for safety signs and limit symbols JR/T 77'R--193J
: Chicken moon type water effector
J3/7 F7:a1905
Electric heating convex fiber insulation umbrella
IB/T 7720-1996
JB/T 7725
1/1 77271495
JB:T7728
IRT 2-P5
Chicken Chuanbietou drinking machine
Central traction scraper cleaning machine
Chicken micro warmer
Chicken condenser machine
Laying hen chicken dragon and firewood
3R/T 9829.11999
JT 8210
3 General requirements
Floating machine technology
Chemical machine test method
3.1 The equipment shall be approved by the prescribed procedures and the technical documents shall be in accordance with T7111710JB/T772CJB/T7725JB:T7727JB/T7728.JB/T7729.JB/T98J9.---9309.2# requirements. 3.2 The equipment shall be equipped with permanent product signs and safety signs, which shall be clearly visible during use. 3.3 After the product is put into use, its performance shall meet the requirements of the system standard. It shall also meet the requirements of the overall performance of the system. 4 Safety requirements
4,1 The equipment shall be connected with the heat exchanger, and 3! F requirements, install limit safety signs on the parts that may cause danger,
4.2 The core equipment should be installed with a transfer insurance contract, and the first two certificates should be guaranteed after installation. The core resistance should not be less than IMo.
4.3 The city gas line is a permanent road, and the voltage fluctuation will not be greater than 10% of the earth. When installing multiple distribution equipment, attention should be paid to the average annual load of three phases.
NY/T 649--20C2
4.4 After the poultry machine equipment is installed, it should be carried out in accordance with relevant regulations. 5 Installation technical provisions
5.1 Drinking water and water operation
5.1.1 The secondary device should be safe and not harmful to the chicken. It should be conducive to the normal drinking water sequence. 5.1.2 The water discharger itself should not be damaged, and its auxiliary parts should not have defects such as damage and broken teeth. 5.1.3 Drinking water and other water sources should be equipped with a filter, and the standard should be changed to monitor the 10 small "2 days" 5.1.4 The water tank should be equipped with anti-rust and anti-mouth materials: the water tank should be strengthened and washed. When adding liquid medicine to the water, consider the light of the liquid to prevent contamination. 6.1. When installing, all joints should be tight and leak-proof. Temporary water should be piped in a non-stop manner and light-proof. 5.1.6 The water pipe should be installed or the water should be installed vertically, and the water discharge device should be installed outside the Gong to prevent the chickens from being poisoned. 5,1.? The water pressure of the filter should be guaranteed to be 2P-kP=(nipple type, heart r 5.2.1 The surface of the material should be smooth and level, and the pulling direction (the speed should not be too fast and the material should not be inclined to the direction of movement, and the surface should not be grooved. 5.2.2 The center of the pulley (chain) and the rotating wheel should be in the same plane, and the difference should not be too large. 5.7.3 The installation of the wheel with a larger angle can be carried out with a cow, 5.2.4 The limit cleaner should be aligned with the rate guide rope, and the rate cleaner and the center stop should be 5.2.5 When the scraper is working, the scraper should be in good contact with the ground: the scraper should be active, and the material should not be dirty when the charger is running empty. 5.2.6 The charger should not be idle when running, and the leveling inspection should be carried out. 5.2. 7. The equipment should be sufficient to allow the price to be contained in the market. The smoke should not be completely separated when it is too negative: 5.2. Please sweep the manure machine every day. 1. The length of the operation should be less than 15.3. The hatching machine should be able to meet the disinfection, egg-lighting, and operation requirements. There should be enough room for the treasures, which is conducive to adjusting the overflow degree of the case. The floor should be short. For cement! Or a piece of hard material sample) the ground is conducive to dry elimination and can accumulate and secrete: 3.3 decomposition, so the weekly use is not allowed to have a strong vibration report. 5.3.4 The amount of green in the damaged environment is not more than 1g.
5.3.5 The environmental temperature during the new chemical month is ~27, and the relative humidity is 40%~H% 5.3.6 The flotation machine (export shaft expansion) should be calibrated before the shutdown of the door table and the stolen temperature field worker average two changes of the safety error 5.3.7 When using a single-action motor, the operation should be uniform and shock-free. 5.4 Feeder
5.4.1 Milling feeder
5.4.1 Feeder and joint should be connected closely: no movement or expansion and contraction is allowed: the gap at the joint should not be more than 1mm, and only the moving part of the chain is allowed to be disconnected
5.4.1.2 Angle wheel installation The difference should not be greater than 3Tn. The interval between the fixed pieces of the rotating device should be adjusted to -m. The amount of wheel should be transferred by the safe elimination action, and the chain system should be flexible 5.4.1.3, the bar or the quality of the link chain should be connected when the movement force is reduced, and the total assembly structure should not be rotated. The elimination piece service is complicated and the force is virtual. The clearing method is dangerous to install the abandoned material box. The installation piece monitors the rotation error of the small data card. 5.4.1.4 The available support should be safe and easy to adjust. When installing the machine, the left frame should be inspected. The total weight of the equipment should be 3 times the weight of the equipment. 5.4.1.5 The internal rotation space of the motor should be 3 times the power space. 5.4.2 Screw spring feeder. 5.4.2.1 Adjust the spring tension to 300~30N on the dial. 5.4.2.2 The material level plate should be able to convey the pipe to the standard to ensure that the equipment can work properly. 5.4.2.3 The material box and the screen should be tightly connected to prevent leakage. Y/T649-2002
5.4.2.4 The steel wire of the support point and the core should have sufficient strength. The magnetic force of the wire rope should not be less than 123N. During installation, it should be ensured that the conveyor is straight and not too flat. 5.4.2.5 The particle size of the cut material should meet the requirements of the corresponding regulations. No hemp rope, stone and other debris are allowed. 5.5 Egg chicken cages and cages
5.5.1 The burning material should be placed on a flat surface of water or other hard carbon materials to facilitate the dissipation and dissipation rate. 5.52 The air should be kept fresh, the room temperature should be kept at 18:-25, and the relative humidity should be kept at 30%-30%. The operating part should have enough air.
5.5.3 The width of each cage frame after installation should not be greater than 1Umm compared with the design width, and the front and rear meshes should be kept vertical to the ground. 5.5.4 The cage frame should not be warped outward, the connection should be smooth, and there should be no vibration. The cage frame and the cage frame should be straight and neat, and the front and rear meshes of each room should be flush, and the horizontality of the room should not be greater than 0.1%, and there should be no twisting. 5.5.5 The water level should be 3 ± 1°, and the difference should not exceed 2.5.5.6 Strictly follow the coal mining, and the mesh should not be opened before the body is deformed. 5.5.7 The installation temperature should be conducive to light and ventilation. 5.6 Electrical insulation
5.6.1 The wiring wires used for insulation should meet the requirements of GH5023.1. 5.6.2 The insulation performance of the door should not be less than 5%. The wiring height of the heating wire inside the heating solution should be 1mm without any difference, buried 25-3m below the ground. The lighting equipment inside should have a separate room and control switch. A thermostat controls a temperature controller to ensure that the temperature and humidity meet the requirements in the table. Table 1 Temperature control requirements Air humidity/r: Internal limit: 20~23.0~35~-45.1 Stomata can be opened Stomata can be closed
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.