title>GB 3883.9-1991 Safety of hand-held power tools Part 2: Special requirements for electric tapping machines (available for certification) - GB 3883.9-1991 - Chinese standardNet - bzxz.net
Home > GB > GB 3883.9-1991 Safety of hand-held power tools Part 2: Special requirements for electric tapping machines (available for certification)
GB 3883.9-1991 Safety of hand-held power tools Part 2: Special requirements for electric tapping machines (available for certification)
Basic Information
Standard ID:
GB 3883.9-1991
Standard Name: Safety of hand-held power tools Part 2: Special requirements for electric tapping machines (available for certification)
GB 3883.9-1991 Safety of hand-held power tools Part 2: Special requirements for electric tapping machines (available for certification) GB3883.9-1991 Standard download and decompression password: www.bzxz.net
Some standard content:
National Standard of the People's Republic of China Safety of hand-held motor-operated electric tools Part 2: Particular requirements for electric tappers( Available for certification) GB3883.9-91 IEC745-2-9 replaces GB3883.9-85 This standard is equivalent to IEC745-2-9 "Safety of Handheld Power Tools Part 2: Special Requirements for Tapping Machines" 1984 first edition. This standard should be used together with GB3883.1 "Safety of Handheld Power Tools Part 1 General Requirements". This standard lists the changes necessary to convert Part 1 into the "Safety Requirements for Tapping Machines" standard. 1 Scope of application Except for the following provisions, this chapter of Part One applies: 1.1 is replaced with: This standard applies to tapping machines. 2 Definitions This chapter of Part One applies except for the following provisions: 2.2.23 Paragraph 1. is replaced by: Normal load refers to the load when the tool operates intermittently with 1 minute of continuous operation and 1 minute of power outage as one cycle. The load applied during continuous operation should have an input power (W) equal to the rated input power. Loads can be applied with brakes. 3 General requirements This chapter of Part 1 applies. 4 General considerations for testing This chapter of Part 1 applies. 5 Ratings This chapter of Part One applies. 6 categories This chapter of Part 1 applies. State Bureau of Technical Supervision approved on 1991-05-27 for implementation on 1992-02-01 7 mark GB3883.9—91 Except for the following provisions, Article Part of this chapter applies: 7.1 Addition: In addition, the tool shall be marked with the following symbol: The maximum diameter of the thread that can be cut, mm. Note: Unless otherwise marked on the tool, this diameter should be understood to refer to the diameter of ISO metric threads cut in steel with a tensile strength of 390N/mm and a thickness of 2 times the thread diameter. 8 Protection against electric shock This chapter of Part 1 applies. 9 Startup This chapter of Part 1 applies. 10 Input power and current Except for the following provisions, this chapter of Part One applies: 10.1 Modification: This test will not be performed. 11 Fever Except for the following provisions, this chapter of Part 1 applies: 11.4 Modification: The tool operates at the specified normal load for 30 minutes. The temperature rise is measured at the end of the last run period. 12Leakage current This chapter of Part 1 applies. 3 Radio and television interference suppression 13 This chapter of Part 1 applies. 14 Moisture resistance This chapter of Part 1 applies. 15 Insulation resistance and dielectric strength This chapter of Part 1 applies. 16 Durability This chapter of Part One applies. 17 Abnormal Operation This chapter of Part 1 applies. Mechanical Hazards 18 This chapter of Part 1 applies. 19 Mechanical Strength This chapter of Part 1 applies. 20 Structure This chapter of Part 1 applies. 21 Internal Wiring This chapter of Part 1 applies. 22 components This chapter from Part 1 applies. 23 Power connection and external flexible cables and cords This chapter of Part 1 applies. 24 Terminal blocks for external conductors This chapter of Part 1 applies. 25 Ground Protection This chapter of Part 1 applies. 26 Screws and Connections This chapter of Part 1 applies. 27 Creepage distances, electrical clearances and insulation penetration distances This chapter of Part 1 applies. 28 Heat resistance, flame resistance and resistance to leakage and tracking. This chapter of Part 1 applies. 29 Rust Prevention This chapter of Part 1 applies. GB3883.9—91Www.bzxZ.net This appendix to Part 1 applies. This addendum to Part 1 applies. This addendum to Part 1 applies. This addendum to Part 1 applies. Additional instructions: GB3883.9—91 Appendix A Thermal circuit breaker and overload release (supplement)||tt ||Appendix B Electronic circuit (Supplement) Appendix C Structure of safety isolation transformer (Supplement)||tt| |Appendix D Measurement of creepage distances and clearances (Supplement) This standard is proposed by the Ministry of Mechanical and Electronics Industry of the People's Republic of China. This standard is under the jurisdiction of the National Technical Committee for Standardization of Power Tools. This standard is drafted by the Shanghai Power Tool Research Institute of the Ministry of Mechanical and Electronic Industry. The main drafters of this standard are Li Hongzhao and Qian Naichi. Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.