This standard specifies the technical requirements for wire and cable twisting equipment. JB/T 5818.1-1991 Technical requirements for wire and cable twisting equipment JB/T5818.1-1991 Standard download decompression password: www.bzxz.net

Mechanical Industry Standard of the People's Republic of China
Wire and Cable Twisting Equipment
Technical Requirements
Part 1
General Requirements
1 Subject Content and Scope of Application
This standard specifies the technical requirements for wire and cable twisting equipment. This standard applies to the technical requirements for twisting equipment for various conductors and cores of wires and cables. JB/T5818.1-91
This standard should be used together with JB/T5814.3 "Basic Parameters of Special Equipment for Wires and Cables Part 3 Twisting Equipment" and JB/T5817.3 "Types and Dimensions of Wire and Cable Twisting Equipment" standards. The provisions of this standard apply to product design, manufacturing, acceptance, identification and quality assessment. 2 Reference standards
GB2900
JB/DQ8124
GB4728
GB4457~4460
JB/T5814.3
JB/T5817.3
GB4004
GB4005
JB/DQ8193
JB4015
JB4032
JB4033
JB2759
3 Terminology
Electrical terminology
Basic technology of cable equipment Requirements
Graphic symbols for electrical use
Mechanical drawing
Basic parameters of special equipment for wires and cables Part 3 Wire stranding equipment
Type and size of wire and cable stranding equipment
Wire and cable machine reels
Wire and cable delivery reels
PND series machine reels
Common parts for cable equipment Wire-reeling and unwinding devices
Common parts for cable equipment Pulling devices
Common parts for cable equipment Wrapping devices
General technical conditions for packaging of electromechanical products
The definitions of terms in this standard adopt the interpretations of GB2900 and relevant standards. 4 General requirements
4.1 The design drawings of each series of equipment shall comply with the provisions of GB4457~4460. 4.2 Electrical drawings shall comply with the provisions of GB4728. 4.3 Products shall be manufactured according to drawings and technical documents approved by the prescribed procedures. 4.4 Self-made parts and components must be inspected and qualified according to regulations before they can be used for assembly. 4.5 Purchased and outsourced parts must have a product quality inspection certificate from the manufacturer and can only be used for assembly after being accepted as required. 4.6 The series composition of the product shall comply with the provisions of JB/T5814.3. 4.7
The type and size of the product shall comply with the provisions of JB/T5817.3, and the installation size and appearance size shall comply with the drawing provisions. Approved by the Ministry of Machinery and Electronics Industry on October 17, 1991 72
Implemented on October 1, 1992
5 Processing quality requirements
JB/T5818.1-91
5.1 General mechanical processing shall comply with the provisions of JB/DQ8124.6. 5.2 Castings shall comply with the provisions of JB/DQ8124.3. Welded parts shall comply with the provisions of JB/DQ8124.4. 5.32
Plated parts shall comply with the provisions of JB/DQ8124.5.
Heat treatment shall comply with the provisions of JB/DQ8124.7. 5.5
5.6Coating and appearance shall comply with the provisions of JB/DQ8124.11. 6Assembly requirements
Before assembly, the accuracy of each link shall be reasonably allocated according to the drawings and assembly process documents. 6.1
For interference fit or single matching, optional parts, the relevant dimensions shall be strictly rechecked before assembly. The level of the machine body, machine base, rotating body, and wire drum rack shall only be leveled, and strong pressure is not allowed. 6.3
The assembly of bearings shall comply with the provisions of JB/DQ8124.9. The assembly of gears and worm transmission components shall comply with the provisions of JB/DQ8124.9. 6.5
The assembly of interference fit shall comply with the provisions of JB/DQ8124.9. The assembly of fasteners shall comply with the provisions of JB/DQ8124.9. 6.7
The assembly of connectors shall comply with the provisions of JB/DQ8124.9. 6.9
The assembly of brakes shall comply with the provisions of JB/DQ8124.9. The assembly accuracy, except for those otherwise specified in this standard, shall comply with the provisions of JB/DQ8124.9. Electrical system
7.1 Electrical materials, independent components and self-contained parts must comply with the relevant standards or technical conditions of each, and can only be used after acceptance.
7.2 The design, assembly and processing of the electrical system shall comply with the provisions of JB/DQ8124.10. 8 Safety requirements
8.1 The equipment should have various signs and labels for lubrication, operation (mechanical, electrical or pneumatic, hydraulic) and safety that meet the specified requirements, and these signs and labels can remain clear for a long time. 8.2 Parts that may automatically loosen during the movement of the equipment should have protective devices, and high-speed reels, baskets, cylinders, ground shafts, etc. should have protective devices; machines or units with large floor space should have safety devices and signal devices. 8.3 Trench covers should be installed in trenches where equipment or components are installed or in trenches at operating locations. 8.4 The equipment should have a good electrical grounding device, and the grounding resistance should comply with the provisions of JB/DQ8124.10. 9 Auxiliary device requirements
9.1 The wire retracting and unwinding device should comply with the provisions of JB4015. 9.2 The traction device should comply with the provisions of JB4032. 9.3 The wrapping device should comply with the provisions of JB4033. 9.4 The reel for taking up and paying out wires shall comply with the provisions of GB4004 and GB4005. The technical requirements for the cage wind reel shall comply with the provisions of JB/DQ8193. 10 Plates and signs
The signs of electrical devices shall comply with the provisions of JB/DQ8124.10 Cage 4. 10.2 The nameplate of the equipment shall be fixed in an appropriate and obvious position on each device. 73
JB/T5818.1-91
10.3 The equipment shall have necessary plates, the signs shall be clear and the position shall be correct. 10.4 The content and format of the nameplate and plate shall comply with special regulations. 11 Packaging
11.1 The packaging of the product shall comply with the provisions of JB2759, be firm and reliable, have anti-rust, anti-leakage and moisture-proof measures, meet the requirements of land and water transportation, and be inspected according to the provisions of JB/DQ8124.1 Article 6.
11.2 The instructions and signs on the packaging box should be placed in an appropriate, obvious and clear position. The signs are as follows: Manufacturer's name
Product name and model
Factory number and date
Product gross weight, net weight, packaging dimensions, center of gravity, lifting line transportation attention characters
Packing number
11.3 Before packaging the product, it should be done
Each moving part should be adjusted to the minimum outline size and fixed. Exclude all liquid substances such as oil and water in the product. Clean the surface, and the unpainted metal surface should be coated with anti-corrosion grease. c.
11.4 Each equipment should be accompanied by the following documents: a.
Product qualification certificate, test report should be provided when the user requires it. Product instruction manual
Packing list
The above documents are packed in a moisture-proof bag and sealed and fixed in the No. 1 packaging box. 12
Acceptance and testing
12.1 Each equipment shall be inspected and qualified by the technical inspection department of the manufacturer before it can be shipped out of the factory. The shipped equipment shall be accompanied by documents proving the quality of the product.
12.2 The products shall be accepted and tested in accordance with the provisions of JB/DQ8124.1. Note:
① The noise is measured at the operating position.
② The noise of the motor shall be assessed in accordance with the motor standard. Additional notes: bZxz.net
This standard is proposed and managed by the Shanghai Cable Research Institute of the Ministry of Machinery and Electronics Industry. This standard was drafted by the Shanghai Cable Research Institute and other units. The main drafter of this standard is Wang Shanqing.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.