HG/T 3596-1999 Polyvinyl chloride pressure-sensitive adhesive tape for electrical insulation HG/T3596-1999 Standard download decompression password: www.bzxz.net

ICS83.180
Record No. 2826-1999
Chemical Industry Standard of the People's Republic of China
HG/T3596---1999
Published on April 20, 1999
Implemented on April 1, 2000Www.bzxZ.net
Published by the State Administration of Petroleum and Chemical Industry
HG/T3596-1999
This standard is equivalent to the industrial standard JIS C2336-1991 "Pressure Sensitive Polyvinyl Chloride Adhesive Tapes for Electrical Insulation". The main difference between this standard and JIS C2336-1991 is that the inspection rules for products are detailed according to the actual situation in my country. This standard was proposed by the Technical Supervision Department of the former Ministry of Chemical Industry of the People's Republic of China. This standard is under the jurisdiction of the National Adhesive Standardization Technical Committee. The drafting unit of this standard: Shanghai Rubber Products Research Institute. The main drafters of this standard: Ju Yinhan and Chen Xiufen. This standard is entrusted to the National Adhesive Standardization Technical Committee for interpretation. 1 Scope
Chemical Industry Standard of the People's Republic of China
Polyvinyl chloride pressure-sensitive adhesive tapes for electrical insulation Pressure Sensitive Polyvinyl Chloride Adhesive Tapes for Electrical Insulation HG/T 3596—1999
This standard specifies the technical requirements, test force method, inspection rules, packaging, marking, transportation and storage of polyvinyl chloride pressure-sensitive adhesive tapes for electrical insulation.
This standard is applicable to pressure-sensitive adhesive tapes with polyvinyl chloride film as the base material and adhesive coated evenly on one side. It is mainly used for electrical insulation.
2 Referenced Standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards are subject to revision. Parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T1692-92 Determination of insulation resistivity of vulcanized rubber GB/T2792-1998 Test method for 180° peel strength of pressure-sensitive adhesive tape GB/T7125-86 Test method for thickness of pressure-sensitive adhesive tape (eddy current method) GB/T7752-87 Test method for power frequency breakdown strength of insulating tape GB/T7753-87 Test method for tensile properties of pressure-sensitive adhesive tape GB/T1451-793 Test method for power frequency withstand voltage of insulating tape 3 Marking and specifications
3.1 Marking
Polyvinyl chloride pressure-sensitive adhesive tape for electrical insulation is indicated as follows: PVC-Insulating Adhesive Tape
19-10 HG/T.XXX× -19 XX
: Standard number
Specification (width 19mm, length 10m)
Code for polyvinyl fluoride insulating adhesive tape
3.2 Specifications
Product specifications, dimensions and deviations shall comply with the provisions of Table 1Approved by the State Administration of Petroleum and Chemical Industry on April 20, 1999 and implemented on April 1, 2000
Basic dimensions
HG/T 3596—1999
Table 1. Specifications, dimensions and deviations
Basic dimensions
1) Special specifications shall be determined by negotiation between the supply and demand parties, and the deviations may refer to the provisions of this table. 2) A roll can have: joints, but the joints cannot appear within 2m at both ends. 4 Technical requirements
4.1 Appearance
Basic dimensions
31~-70
The adhesive tape should be wound into a roll evenly, without obvious deformation and winding gaps, and the two sides should be flat and straight without missing or overflowing glue. The color of the adhesive tape should be even, without wrinkles, scars, impurities and other defects that affect the performance. There is no glue on the back of the adhesive tape.
4.2 Performance
The performance of the adhesive tape should comply with the requirements of Table 2.
Table 2 Properties
Tensile strength, N/cm
Elongation at break, %
180° peel strength, N/cm
Breakdown strength, positive V/mm
Withstand voltage 5kVX1nmin
Volume resistivity, n+cm
Note: For breakdown strength and withstand voltage performance, one of the two indicators can be selected. 5 Test method
5.1 Appearance
No breakdown
1×1012
Inspect by visual method. Unwind about 1m long adhesive tape within 3~5s to check whether there is adhesive migration to the back of the adhesive tape. 5.2 Size
5.2.1 Thickness of adhesive tape
Measure according to GB/T7125.
5.2.2 Width of adhesive tape
Measure with a vernier gauge with a scale of 0.02 mm. Measure two points on each roll, accurate to 0.1 mm, and take the median value. 5-2.3 Length of adhesive tape
Measure with a steel sheet with a scale of ］mm. When measuring, the adhesive tape should be left for more than 1 minute after unwinding. The length of the adhesive tape should be accurate to 1 cm.
5.3 Performance
5.3.1 Tensile strength of adhesive tape
According to the test case specified in GR/T7753
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.