This standard specifies the product classification, technical requirements, test methods, inspection rules and marking, packaging, transportation and storage of aluminum-plastic composite fabrics (hereinafter referred to as fabrics) composed of plastic film, plastic woven fabric and aluminum. This standard applies to the manufacture, use, circulation and supervision and inspection of aluminum-plastic composite fabric products. BB/T 0017-1999 Aluminum-plastic reinforced composite fabric BB/T0017-1999 Standard download decompression password: www.bzxz.net
This standard specifies the product classification, technical requirements, test methods, inspection rules and marking, packaging, transportation and storage of aluminum-plastic composite fabrics (hereinafter referred to as fabrics) composed of plastic film, plastic woven fabric and aluminum. This standard applies to the manufacture, use, circulation and supervision and inspection of aluminum-plastic composite fabric products.

Packaging Industry Standard of the People's Republic of China
BB/T 0017 - 1999
Aluminum-plastic reinforced composite fabric
Laminated aluminium plastics fabric by reinforce1999-09-16Published
Published by China National Packaging Corporation
Implemented on 1999-10-01
BB/T0017—1999
Aluminum-plastic reinforced composite fabric is composited with plastic fabric in the middle of the fabric layer. It has the characteristics of high strength, impact resistance, softness, good barrier performance, etc. It can be widely used in the fields of color decoration, machinery, chemical industry, materials, pesticides, weapons, etc. In order to meet the needs of the production development and application of aluminum-plastic composite fabric in my country and standardize the technical parameters of aluminum-plastic composite fabric products in my country, this standard is formulated.
This standard is proposed by Zhongju Packaging Corporation. This standard is under the jurisdiction of the National Technical Committee for Packaging Standardization. The responsible drafting units of this standard are: Mechanical Science Research Institute of the Ministry of Machinery Industry and Changzhou Zhonghua Qinban Plastic Co., Ltd. The main drafters of this standard are Cheng Tiexing, Li Xuelong, Wu Guoqing, Huang Xue and Zhang Zhengfu. This standard was first issued on September 16, 1999. Scope
Packaging Industry Standard of the People's Republic of China
Aluminum-plastic reinforced composite fabric
Laminated aluminium plastics fabric reinforced composite fabric BB/T 0017- 1999
This standard specifies the product classification, technical requirements, test methods, inspection rules and marking, packaging, transportation and storage of aluminum-plastic composite fabric (hereinafter referred to as fabric) which is composed of plastic film, plastic woven fabric and aluminum. This standard is applicable to the production, use, circulation and supervision inspection of aluminum-plastic composite fabric products. 2 Referenced standards
The provisions contained in the following standards constitute the provisions of this standard by being referenced in this standard. When this standard is published, the versions shown are valid. All standards will be revised. Parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T10371988Test method for water vapor permeability of plastic film and sheet GB/T1038-1970Test method for air permeability of plastic film GB/T6673-1986Determination of length and width of plastic film and sheet GB/T8809-1988
Test method for pendulum impact resistance of plastic film
GB/T 165781996
QB/T 3808—1999
3 Classification and marking
Test method for tear resistance of plastic film and sheet Trouser tear method
Composite plastic woven cloth
The cloth is divided into aluminized type and aluminum foil type. Its code, name and structure are shown in Table 1. 3.1
Table 1 Code, name and structure of cloth
Lead-plated type
Aluminum foil type
(LB type)
3.2 Marking
Aluminum-plated aluminum-plastic composite
Platinum-foil aluminum-plastic composite fabric
Approved by China National Packaging Corporation on September 16, 1999
Plastic film/aluminum-plated layer/adhesive layer/woven fabric/heat-sealed layer
Mass per square meter of plastic film/aluminum-plated layer/adhesive layer/woven fabric/heat-sealed layer bZxz.net
Fabric width (mm)
-Fabric type code (DL or LB)
Aluminum-plastic film code
1999-10-01 implementation
4 Requirements
4.1 Specifications and dimensions and limit deviations
BB/T 0017 1999
The specifications and dimensions and limit deviations of fabrics shall comply with the provisions of Table 2. Special specifications and dimensions shall be agreed upon by the supplier and the belt supplier. Table 2 Specifications of cloth Size and eye deviation
Length Size, m
Width Size, mm
Mass per square meter + name/m
4.2 Appearance
4.2.1 The appearance of the cloth shall comply with the requirements of Table 3. Table 3 Appearance of cloth
Bubbles, perforations
Warp density version
Cloth surface can have
Specifications
200-1000
More than 200
130200
140--210
Within any 100m㎡×109mm, the number of missing warp and weft threads shall not exceed 2. Within any 100m㎡×100mm, the final density shall be greater than 3mm in width and 1100m in length. No obvious stains caused by oil or other reasons are allowed. Obvious burns and unevenness are not allowed at the bonding point. The composite layer shall not be separated
Limit deviation
1-10mm
±15 g/m*
4.2.2 For rolls with a length of no more than 300m, the number of joints shall not exceed 1; for rolls with a length of more than 300m, the number of joints shall not exceed 2, and the continuous length of the cloth shall not be less than 100ml. The joints shall be connected and marked clearly. 4.3 Physical and mechanical properties of the cloth
The physical and mechanical properties of the cloth shall comply with the provisions of Table 4. Table 4 Physical and mechanical properties of the cloth
Tensile strength (longitudinal direction), N/5cm
Elongation of broken pieces (longitudinal and transverse directions)%
Maximum tearing force, N
Anti-pendulum impact performance, I
Water permeability, z/(ms.24 ht)
Oxygen permeability, cm/(m·1.01325MPa·24h)2
5 Test method
5. 1 Measurement of length and width of fabric
BB/T 0017—1999
Measurement of length and width shall be carried out in accordance with the provisions of GB/T6673. When fabric is ordered in rolls, the actual length of the fabric shall not be less than the specified length in the order.
5.2 Measurement of the mass per square meter of fabric
According to the provisions of QB/T3808.
5.3 Appearance inspection of fabric
Visual inspection under natural conditions.
5.4 Determination of tensile strength and tear elongation
According to the provisions of QB/T3808.
5.5 Determination of maximum tear force
According to the provisions of GB/T 16578.
5.6 Determination of pendulum impact resistance
According to GB/T 8809
5.7 Determination of water vapor transmission rate
Perform according to the provisions of GB/T1037.
5.8 Determination of oxygen transmission rate
Perform according to the provisions of GB/T1038.
6 Inspection rules
6.1 General
Fabric inspection is changed to batch. 30 rolls of the same variety and same pattern are a batch. 6.2 Inspection classification
Product inspection is divided into factory inspection and type inspection. 6.3 Factory inspection
Factory inspection items are size and appearance inspection. During the factory inspection, 1/2 rolls of each batch are taken out for inspection. If there are unqualified items (the maximum number of unqualified items shall not exceed 3, otherwise it shall be judged as unqualified), the unqualified items shall be re-inspected by random sampling from the original batch. If the re-inspection result is still unqualified, the batch shall be judged as unqualified.
6.4 Type inspection
Type inspection is a full-item inspection.
During type inspection, three rolls are taken from each batch to take out 1.m samples for inspection. The physical and mechanical properties of the cloth, except for 5.7 and 5.8, are inspected once for each item. When the process or original material changes, a type inspection should be carried out. If any item in the type inspection fails, the unqualified items should be re-inspected by randomly selecting double from the original material. If the re-inspection result is still qualified, the type inspection is judged to be unqualified.
7 Marking, packaging, transportation, storage
7.1 Marking
Each roll of cloth should be marked with product name, trademark, manufacturer name, factory address, weight, batch, standard number, production date, inspector's seal, etc.
7.2 Packaging
The product should be reliably packaged with paper/composite cloth, coated plastic woven cloth, etc., and the support should be firm. The edge of the packaging cloth is sealed with adhesive tape: 7.3 Transportation
BB/T 0017—1999
During transportation, the product should be loaded and unloaded gently to prevent mechanical damage, rain, and avoid rabbit powder pollution. 7.4 Purchase and storage
The product should be stored in a clean, cool and dry warehouse, less than 1m away from the heat source. The storage period shall not exceed two years from the date of production.
Copyright reserved. Reproduction is prohibited
Book number: 155066·2.13133
Pricing:
Standard 415-32
China People's Government Packaging
Industry Standard
Aluminum-plastic reinforced composite fabric
BB/T 0017—1999
Published by China Biaoya Publishing House
No. 16, Hebei Street, Sanzhi, Fuxingmenwai, Beijing
Postal Code: 1C0045
Tel: 68522112
Printed in Qinhuangdao, China Biaoya Publishing House, distributed by Xinhua Bookstore in Beijing, sold by Xinhua Bookstores in various places. Copyright is exclusive and no reproduction is allowed
Format 880×12301/16 Printing Sheet 1/2 Number of Words 8,000 First Edition August 2600 Second Printing August 2000 Number of Prints 1800
Book Number: 155066:2-13133
Price 6.00 Yuan
Standard Month 415—32
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.