This standard specifies the inspection conditions, inspection gauges and general inspection methods for the appearance quality of finished shoes and boots. This standard is applicable to the inspection of the appearance quality of various finished shoes and boots. GB/T 3903.5-1995 General inspection method for footwear Appearance inspection method GB/T3903.5-1995 Standard download decompression password: www.bzxz.net

UDC 685. 3. 001. 4
National Standard of the People's Republic of ChinawwW.bzxz.Net
GB/T3903.51995
General test method for footwearTest method of appearance
Issued on August 17, 1995
State Bureau of Technical Supervision
Implementation on August 1, 1996
National Standard of the People's Republic of China
General test method for footwear
Test method of appearance
General test method for FootwearT'est metbod of appearance
1 Subject content and scope of application
Specifies the inspection parts, inspection measuring tools and general inspection methods for the special and complete quality of finished products. This standard is applicable to the inspection of the appearance quality of various finished shoes and batches under the current situation. 2 Inspection
The inspection of the appearance quality of footwear should be carried out in a room with sufficient light. 3 Inspection tools and tools
3.1 Shoe tape scale graduation 1.0mm.
3.2 Group mark card graduation 0.05mm
3. 3 Pivot ruler graduation 1.mm.
3. 4 Height vernier caliper graduation 0.05mm
3.5 Width angle ruler 90″3.
3. 6 Marble slabs,
4 Inspection methods
Control inspection methods Table 1 and use 1~4 times. When the daily test items occur, the test tools are used for inspection. Table 1
Inspection items are mainly in appearance
Height of back upper
Certified period price
National case technical supervision requires approval on August 17, 1995
GAT 3903 5—1995
Niu Huiri inspects whether the product is straight, symmetrical, flat, smooth, consistent in color, clean, and complete. All parts such as the original and the length are intact. The belt should be adjusted with the standard caliper. The defects can be measured with the caliper at the midpoint or specific position (the length of the belt, the tongue, etc.) of the belt. The outer Baotou store can also measure the height of the midpoint along the midpoint (see time 2). ]
Use a tape measure to follow a quadrant point to a test point, the whole test Wa evil two 5 obtained the old difference
1996-日-01 implementation
Quick point
Build a new
(internal limit)
External original length
External energy research
External Binbo Kang
Small in length
Student Union Construction
Installation language installation: degree
GB,T 3903.5~-1995
Continued Table 1
Put the big moon seat edge
point with a ruler to measure the flux and then use a ruler to measure the vertical edge of the big broken height. See Figure 31. The wine quality needle code product contains, I am suitable and neat, there is red, broken line, book level, light measurement needle product wall line fan pull light, needle code book with cursor: Xing side put the day outsourcing (store consultation sales positive flat non-same sex inside only the outsourcing (after) follow you, with regret and use the finger to press on both sides of the external storage limit, depending on the case and its color change and the original situation of joy, whether the day outsourcing is with the right ,, the same two eat the outer head is for you, with the variable finger connection request package 1, the case of its deformation and system conditions to build with a tape measure to measure the outside of the front point of the outer bottom (the outside between the end points of the Chang'an || tt || will increase the length of the inner side of the marble cabinet vertically, with the five-center vertical state to measure the outer false version of this level report the highest danger, that is, the outer bottom section with a steel foot measurement through the transition, if necessary, the outer material line will be divided to measure the outer system of the corresponding Ai Shao material, the bottom filling or space, etc., the usage of the measurement card measurement
Over time, with a special tape ruler, you can think of the distance between the low and the end point. When sampling, you can take the same type of product as the insured and carry out measurement on the marble bottom. The standard point is measured on the marble. The distance from the external sliding point to the large stone seat (Xun 4 sales) will be non-certified on the marble. The card line
is on the marble surface (Diamond B) according to the high light (West 4) on the large elastic stone slab. The schedule is the overall coordination, symmetry, the next question (Purple use seven to level (One month later, hold the other one and wait for the time being. The shoes will be moved to the parties. Three and three days later, the products must be repaired by hand. Find one hand and point to the back of the belt. There is no image of light or strands. Hold a single hand and pull the assembly parts lightly. Observe whether the surface edge point of the belt is solid or not: front point GB/T3903.5-1995 1 side: ? When the appearance inspection method in the standard and inspection method of footwear products is inconsistent with this standard, this standard shall prevail. Additional remarks: This standard is proposed by the five trade unions. This standard was issued by the National Standardization Center. This standard was approved by the Silicon Industry Science Research Institute of the Ministry of Industry and Information Technology. The three main drafters of this title are Zhou Jing and Yan Huaidao.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.