[CS 37.100.10
Machinery Industry Standard of the People's Republic of China
F8/T 8116-1998
Platen-die cutting and creasing machine1998-3-19 Issued
Ministry of Machinery Industry of the People's Republic of China
Implementation on 1998-07-01
JB/T-8116-1998
This standard is a revision of JB/8116-95 flat-die cutting machine. This standard has some changes in the following important technical contents compared with the standard of the integration: The technical data related to automatic vertical flat-die cutting machine are added to the type: The format is formulated in accordance with GB/15467-1995<Printing Technology Sheet-fed Printing Machine Dimension Series 3: The inspection and calculation method of die scratching error is specified! Reduce the noise level of semi-automatic flat die-cutting machines: Increase the requirements for the efficiency and air quality of automatic flat die-cutting machines. This standard will replace JB/T8116-95 from the date of implementation. This standard is proposed and managed by the National Printing and Testing Machine Standardization Technical Committee. The responsible drafting unit of this standard: Shanghai Yahua Printing Machinery Co., Ltd. This standard is the standard of the People's Republic of China Machinery Industry Standards. $11G.-I998
The technical standard [B/T8116-95
specifies the type and basic functions, technical requirements, test methods, inspection plan, marking, packaging, transportation and storage of flat die-cutting machines (hereinafter referred to as flat die-cutting machines). This standard is narrowly applicable to flat die-cutting machines: it is also applicable to the die-cutting and creasing parts of flat die-cutting machines and flat die-cutting machines. 2 References
The provisions contained in the following standards are considered to be the provisions of this standard through reference in this standard. When this standard is revised, the versions shown are all valid. All standards will be ordered by you + the possible use of new versions of the following standards should be explored for the various types of old and fixed standards, GB 191-90 GB/T 1182-1996 GB 4879-85 GB/I 5226.1-1946 GR6388-86 GB/11330691 GB/T 1338402 JB309-82 Z C8 001—3 Types and basic parameters 3.1 Types 3.1.1 Dynamic flat die-cutting machines: a) Horizontal die-cutting machine; b) Vertical die-cutting machine.
3.1.2 Semi-automatic flat die-cutting machine
3.2 Basic requirements 1.
Packing and shipping graphic symbols
Shape and position specifications and specifications
Rust-proof packaging
Industrial machinery and electrical equipment Part 1: General technical conditions Shipping packaging Receiving and shipping markings
Technical regulations for packaging of electromechanical products
Printing machinery product vertical number compilation method
bzxz.netDie-cutting and creasing mechanical safety technical regulations
3.3 The model and name of the product shall comply with the provisions of JB3090. Approved by the Ministry of Machinery Industry 1
Implemented on July 1, 1998
Automatic die-cutting machine
Horizontal flat press
Vertical press
Mold straightening machine
Automatic press
Variation machine
4 Technical requirements
JB/TB116—1998
710×1620~90×12H0
>510×710~710×1020
2355×51~51X710
>710X1421~0X1283
>516×710~710×1020
:355X51C--51DX710
>900×12501220×1600
7101020-900×1280
>511×713--716X1620
350X510~310×710
, trade mold specification
235500
4.1 Flat die-cutting machine shall comply with the provisions of this standard and be manufactured according to drawings and technical documents approved by the prescribed procedures: 4.2 Assembly quality
Large die-cutting machine
Large station flat die-cutting machine two working plates (vertical or die-cutting machine for the machine base plate and the press frame plate> parallelism in the closed position, shall not be lower than the tolerance grade 7 specified in GB/T1184: half The performance of the automatic flat press cross-cutting machine base plate and the press frame plate in the vertical position shall not be lower than the B grade specified in GB/T1184. 4.3 The transmission system runs smoothly, works normally, and there is no abnormal noise. 4.4 Ensure that the machine is sensitive and movable, and the actuators are coordinated and reliable without jamming or spontaneous movement. The automatic flat press cutting machine can automatically control the air, press and cut effectively, and cut large machine movements. 4.5 The system pipeline is unobstructed, and the oil supply to each lubrication point is divided without any leakage. 4.6 The bearing load shall not be raised too low. 4. The cut product should be cut through and cut lightly. The whole is free of hair scratches, the surface is flat, the convex and concave are clear, the paper fibers are continuous, and it meets the requirements of the tray packaging process.
4.8 The die-cutting line deviation of the flat-bed die-cutting machine with a format less than 1000mm×1280mm shall not exceed ±0.20mm, and the qualified rate shall not be less than 96%. The die-cutting line deviation of the flat-bed die-cutting machine with a format greater than 900m×12mm shall not exceed ±0.3mm, and the qualified rate shall not be less than 96%. 4.9 The noise of the automatic horizontal flat-bed die-cutting machine is not loud. The noise of the automatic vertical flat-bed die-cutting machine is not more than 82dManufacturer name:
b) Product number, name:
) Product main production batch number:
Date (or shortened date) Production batch number, 1.2 Packaging storage and transportation signs should be provided for products to be transported in accordance with the relevant provisions of G1S1. For packaging that requires single-piece transportation and whose center of gravity is obviously deviated from the center, the signs of "lift from here" and "center" should be marked. 7.1.3 When the product is packed in multiple boxes, the box number should be expressed in fractions, with the numerator being the number and the denominator being the total number of boxes. The box number should be No. 1. 7.1.4 The shipping and receiving signs of the transportation packaging should follow the provisions of GB6368. 7.2 Packaging
7.2.1 Before packing, the rust-proof packaging of machine parts, tool spare parts and the exposed processing surface of the parts shall comply with the grade of anti-rust packaging in GB4379, and the grade of rust-proof packaging shall be selected. 7.22 The production and transfer requirements of product packaging boxes shall comply with the relevant provisions of GB/T13384. 7.2.3 Random documents
The following random documents are attached to the product when it leaves the factory: product certificate, product manual and packing list (including general packing list and sub-packing list). If the product is packed in multiple boxes, the random documents should be in the main box, and the classified packing list should be placed in the corresponding packaging box. 7.3 Transportation
JR/T8116—1998
When the product is transported and lifted, the markings on the outer wall of the packaging box should be touched to prevent it from being touched. 4 Storage
The product should be stored in a dry and ventilated place to avoid moisture. When stored outdoors, the packaging box should be rainproof. If the storage period exceeds 2 years, it should be unpacked and checked before leaving the factory. If it is found that the product packaging does not meet the relevant regulations, it should be repacked. 5
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.