Some standard content:
People's Republic of China Building Industry Standard Automatic Swing Doors
JG/T3015.2-94
Approved by the Ministry of Construction of the People's Republic of China on April 20, 1994 and implemented on December 1, 1994
1 Subject Content and Scope of Application
This standard specifies the product classification, technical requirements, test methods, inspection rules and marking, packaging, transportation and storage of automatic swing doors.
This standard applies to swing doors that automatically open and close at the entrances and exits of buildings, namely automatic swing doors (hereinafter referred to as doors), with the code PDM.
Referenced standards
GB 191
Packaging, storage and transportation pictorial symbols
GB2423.1 Basic environmental test procedures for electric and electronic products Test A: Low temperature test method GB2423.2 Basic environmental test procedures for electric and electronic products Test B: High temperature test method GB 2423. 3
Basic environmental test procedures for electric and electronic products Test Ca: Steady-state damp heat test method GB 3797
Electrical control equipment Part 2: Electrical control equipment equipped with electronic devices General safety requirements for household and similar electrical appliances GB 4706. 1
GB5237
GB 5824
GB6388
3 Product classification
Aluminum alloy building profiles
Building door and window opening size series
Transportation packaging delivery and receipt mark
Basic door thickness size:
Basic door thickness size, divided by the thickness of the door frame, see Table 1. mm
Basic door thickness size series
3.2 Door opening size series:
3.2.1 The width and height of the door are mainly determined according to the installation requirements of the opening. The specifications and models of the basic door opening are shown in Table 2.
Except as specified in Table 2, any combination of doors is allowed, and the size of the combined opening shall comply with the specifications of GB5824. 3.2.3
Height, mm
Width, mm
3.3 Basic facade types of doors:
a) Single door,
b) Single-leaf door with upper light;Www.bzxZ.net
e) Double-leaf door;
d) Double-leaf door with upper light.
Note: 1) The above basic facade types are shown in Table 3. 2) Other types of doors can be designed and manufactured according to the requirements of the product. 3.4 The basic dimensions of the door leaf are 2100 and 2400mm. 3.5 The weight of a single door leaf is divided into three levels: 30, 50 and 70 kg. 3.6 Classification by door structure:
a) Framed door, code Y;
b) Frameless door, code W.
3.7 Classification by detection device:
a) Microwave detector, code B;
b) Infrared detector, code H;
c) Ultrasonic detector, code C;
d) Electromagnetic induction detector, code D; e) Special detector, code T.
3.8 Switching direction:
3.8.1 The switching direction of a single door is shown in Table 4.
Switching direction code
The door leaf closes from inside to outside in clockwise direction
The door leaf closes from inside to outside in counterclockwise direction
The door leaf closes from outside to inside in clockwise direction
The door leaf closes from outside to inside in counterclockwise direction
See Table 5 for the switching direction of double-leaf doors.
Switching direction code
4 Technical requirements
Both door leaves close from inside to outside at the same time
Both door leaves close from outside to inside at the same time
4.1.1 The door body material is made of aluminum alloy building profiles, and other materials can also be used. Figure
Civil 1 Foreign
4.1.2 Aluminum alloy building profiles for doors shall comply with the provisions of GB5237, and other materials and accessories shall comply with the current national standards and industry standards.
4.1.3 Except for stainless steel or corrosion-resistant materials, the materials of doors and selected parts and accessories shall be treated with rust and corrosion prevention, and contact corrosion with aluminum alloy profiles is not allowed. 4.2 Assembly requirements
4.2.1 The dimensional deviation of the door frame made of profiles shall comply with the requirements of Table 6. mm
The inner width and height of the door frame are allowed
The inner side opposite side dimensions of the door frame
The inner diagonal dimensions of the door frame
Superior products
First-class products
Qualified products
4.2.2 The assembly clearance and flatness of the adjacent components of the door frame and the sash made of profiles shall comply with the requirements of Table 7. mm2Table 7
Flatness
Superior
Second-class
Qualified
Assembly clearance
Superior
First-class
Qualified
4.2.3The connection of door components should be firm, and the structure should have sufficient strength and rigidity to withstand the installation of drive, control and other components and ensure that the door can be opened and closed freely.
4.2.4The verticality of the door frame shall not exceed 1mm per meter. The horizontality of the upper frame shall not exceed 1mm per meter. 4.2.5The clearance between the door frame and the leaf shall be evenly matched. When fully closed, the limit deviation of the clearance between the leaf and the frame shall not exceed ±1.5mm, and the limit deviation of the clearance between the leaf and the leaf shall not exceed ±1.5mm. 4.2.6The installation of door parts and accessories shall be correct, complete and firm, play their respective roles, have sufficient strength, and be flexible to open and close.
4.3 Surface quality
4.3.1 The decorative surface of the door should not have obvious damage and defects that affect performance. The local scratches and abrasions on each door should comply with the corresponding standards or relevant standards.
4.3.2 There should be no obvious color difference between the colored surfaces of adjacent components of the door. 4.3.3 There should be no metal shavings, burrs, corrosion marks and other stains on the door surface. 4.4 Door performance
4.4.1 The power supply voltage for the door is AC220V±10%, and the frequency is 50Hz. 4.4.2 The detection range of ultrasonic, infrared and microwave detectors should be adjustable, and their detection area should meet the requirements of Table 8. Table 8
Detection device type
Ultrasonic detector
Detection area, m2
Detection device type
Infrared detector
Detection area, m2
Detection device type
Microwave detector
Detector installation should ensure that the distance between the edge of its blind area and the door is no more than 200mm. 4.4.3
Detection area, m2
The door should open and close sensitively. When a person or object passes through the detection range at a speed of 0.3m/s, it should open and close normally. 4.4.5 The opening (or closing) time should be 2 to 4s. Before the door is fully opened or fully closed, the door speed is reduced to a safe and reliable slow speed, and it is adjustable, with obvious buffering, and smooth opening and closing.
4.4.7 The door opening response time should not be more than 0.5s. 4.4.8 The delay of the door blocking protection shall not exceed 18s. 4.4.9 The door opening holding time is adjustable from 0.5 to 10s. 4.4.10 When the door is working normally, the operating noise shall not exceed 65dB. When the door is cut off from the power supply, the manual door opening torque shall not exceed 45N·m. 4.4. 11
The insulation resistance shall not be less than 2MQ under hot and humid conditions. 4. 4. 12
4.4.13 The door's live main circuit and metal casing shall be able to withstand AC1500V and have no breakdown within 1min. The door shall be able to work normally under the condition of a 10-50℃ working environment temperature. 4. 4. 14
The door shall be able to work normally under the condition of an ambient working environment temperature of 40℃ and a maximum relative humidity of 80%. 4. 4. 15
4.4.16 Under normal working conditions, the service life of the door shall not be less than 500,000 times. 5 Test methods
5.1 Inspection of the contents of Article 4.1
Use visual inspection.
5.2 Inspection of the contents of Articles 4.2 and 4.3
Use special instruments such as steel tape measure, feeler gauge, caliper, level gauge, and visual inspection and hand feeling methods to inspect. 5.3 Inspection of the contents of Article 4.4.1
Use a voltage regulator to adjust the power supply voltage and use a multimeter to inspect. 5.4 Test of the contents of Articles 4.4.2 to 4.4.4 A person with a height of not less than 1.5m enters the specified detection range at a speed of 0.3m/s to observe whether the door leaf can be opened and whether the movement is good, and measure the distance between the edge of the detection blind area and the door. 5.5 Test for 4.4.5
The door under test is in normal working condition. Use a timer to measure the time for the door leaf to move from the fully closed position to the fully open position (or from the fully open position to the fully closed position). Repeat the test for 3 times and take the average value. 5.6 Test for 4.4.Test of 6
Put the door under test in working state, start the control system, make the door leaf fully open and fully closed, and observe whether the door leaf operates smoothly for 3 consecutive times.
5.7 Test of 4.4.7
Put the door leaf in normal working state in closed position, start with a stationary human body standing in the detection area, observe and use a timer to record the time from the human body moving to the door leaf starting. Test 3 consecutive times and take the average value. 5.8 Test of 4.4.8
Use a timer to record the time from the door leaf contacting the person blocking the door to the door automatically stopping closing during the automatic opening and closing process. Test 3 consecutive times and take the average value. 5.9 Test of 4.4.9
Use a timer to record the time from the door leaf opening to the detector signal disappearing to the door leaf starting closing during the automatic opening and closing process, and can adjust it within the specified time range. 5.10 Test for 4.4.10
Under the condition that the ambient noise is not more than 45dB, use a Class A sound level meter to measure the noise of the door in normal working state at a distance of 1m before and after the center of the door and a height of 1.5m. Measure three times in succession and take the average value. 5.11 Test for 4.4.11
After disconnecting the power supply, use a dynamometer to pull the door leaf to make a hook speed rotation in the closed state, the middle state and the fully open state, and measure the door opening torque. Test three times in succession and take the average value. 5.12 Test for 4.4.12
Perform the test according to the test method specified in GB4706.1. 5.13 Test for 4.4.13
Perform the test according to the test method specified in Article 4.4 of GB3797. 5.14 Test for 4.4.14
Perform the test according to the test method specified in GB2423.1 Test Ab and GB2423.2 Test Bb, and check whether the appearance of the test piece is damaged and whether it can work normally.
5.15 Test for 4.4.15
Perform the test according to the test method specified in GB2423.3 Test Ca, and the test severity level is 2 days, and check whether the appearance of the test piece is damaged and whether it can work normally.
5.16 Test for 4.4.16
Start the control button, open and close once in a cycle of 10 to 30 seconds, and run back and forth continuously for 500,000 times. Secondary replacement of wearing parts is allowed during the whole process.
6 Inspection rules
6.1 Factory inspection
6.1.1 Before leaving the factory, the product must be inspected and qualified by the quality inspection department of the manufacturer, and the certificate of conformity must be issued before it can leave the factory. 6.1.2 Factory inspection items:
Inspection shall be carried out in accordance with the contents and requirements specified in Articles 4.1~~4.3, 4.4.2~4.4.12 of this standard. 6.1.3 Sampling method and judgment rules:
The sampling inspection of each project shall not be less than 50%, but the number of sampling inspections shall not be less than two. If all the inspection items are qualified, it is qualified. When one of them is unqualified, the sampling inspection shall be doubled. If the item is still unqualified, the batch shall be judged as unqualified. All unqualified products shall be returned for repair and can only be delivered after passing the re-inspection. 6.2 Type inspection
6.2.1 Type inspection shall be conducted in any of the following cases: a) Trial design and identification of new products or old products for transfer to factory production; b) After normal production, when there are major changes in structure, materials, and processes that may affect product performance; c) During normal production, when continuous production lasts for more than five years; d) When production is resumed after more than one year of suspension;
e) When the national quality supervision agency proposes a requirement for type inspection. 6.2.2 Type inspection items and judgment rules: Tests shall be conducted in accordance with the contents and requirements specified in Chapter 4 of this standard. 6.2.3 Sampling method:
Type inspection shall be conducted by sampling 3 from qualified products. If all the inspection items are qualified, it is qualified. When one of them is unqualified, double sampling shall be conducted. If the item is still unqualified, the batch shall be judged as unqualified. Unqualified products are allowed to be returned for re-inspection.
7 Marking, packaging, transportation and storage
7.1 Marking
7.1.1 There should be a nameplate on the obvious part of the product, which should indicate: a) trademark and manufacturer's name;
b) product name;
c) product model,
d) manufacturing date or number.
7.1.2 The markings on the packaging box should comply with the provisions of GB6388. 959
7.1.3 The packaging box should have words and signs such as "moisture-proof", "handle with care" and "upward", and the pattern should comply with the provisions of GB191.
7.2 Packaging
7.2.1 The product should be packaged with non-corrosive materials. 7.2.2 The packaging box should have sufficient strength and be moisture-proof and shock-proof. 7.2.3 The products packed in the box should be guaranteed not to move with each other. 7.2.4 After the product is packed, the box must contain a packing list, product certificate, product manual and warranty card. 7.3 Transportation
7.3.1 The transportation vehicle should be rainproof and kept clean and free of dirt. 7.3.2 The product is strictly prohibited from falling or colliding during transportation and loading and unloading, and the geometric shape of the product should be kept unchanged and the surface should be intact. 7.4 Storage
7.4.1 The product should be placed in a ventilated and dry place. It is strictly prohibited to contact with acids, alkalis and salt substances, and prevent rain from soaking people. 7.4.2 The product cannot directly contact the ground, and the bottom should be raised by more than 100mm. Additional instructions:
This standard is proposed by the Standard and Quota Research Institute of the Ministry of Construction. This standard is under the jurisdiction of the China Building Standard Design Institute, the technical unit responsible for standardization of building products and equipment. This standard is drafted by the China Building Metal Structure Association (the main drafting unit), Shanxi Electronic Instrument Factory (Shanxi Automatic Door Company), and Suzhou Suxin Decoration Industry Corporation. The main drafters of this standard are Cui Yongfeng, Xu Zichang, Sun Junan, Jin Shunxing and Tao Hongxing. The China Building Standard Design Institute is entrusted with the interpretation of this standard.3 Sampling method and judgment rules:
For each project, no less than 50% shall be sampled, but the number of samples shall not be less than two. If all the inspection items are qualified, it is qualified. When one of them is unqualified, the sampling should be doubled. If the item is still unqualified, the batch is judged to be unqualified. All unqualified products should be repaired and can only be delivered after re-inspection. 6.2 Type inspection
6.2.1 Type inspection should be carried out in any of the following situations: a) Trial production and identification of new products or old products transferred to the factory for production; b) After normal production, when there are major changes in structure, materials, and processes that may affect product performance; c) During normal production, when continuous production is more than five years; d) When production is resumed after more than one year of suspension;
e) When the national quality supervision agency proposes a requirement for type inspection. 6.2.2 Type inspection items and judgment rules: Tests shall be carried out in accordance with the contents and requirements specified in Chapter 4 of this standard. 6.2.3 Sampling method:
3 samples are randomly selected from qualified products for type inspection. If all the inspection items are qualified, the batch is qualified. If one of them is unqualified, double sampling should be carried out. If the item is still unqualified, the batch is judged to be unqualified. Unqualified products are allowed to be returned for re-inspection.
7 Marking, packaging, transportation and storage
7.1 Marking
7.1.1 There should be a nameplate in a conspicuous part of the product, which should indicate: a) trademark and manufacturer's name;
b) product name;
c) product model,
d) manufacturing date or number.
7.1.2 The marking on the box surface of the packaging box should comply with the provisions of GB6388. 959
7.1.3 The packaging box should have words and signs such as "moisture-proof", "handle with care" and "upward", and the pattern should comply with the provisions of GB191.
7.2 Packaging
7.2.1 Products should be packaged with non-corrosive materials.7.2.2 The packaging box should have sufficient strength and be moisture-proof and shock-proof. 7.2.3 Products packed in the box should be guaranteed not to move with each other. 7.2.4 After the products are packed, the box must contain a packing list, product certificate, product instruction manual and warranty card. 7.3 Transportation
7.3.1 The means of transport should be rainproof and kept clean and free of dirt. 7.3.2 Products are strictly prohibited from falling or colliding during transportation and loading and unloading. The geometric shape of the product should remain unchanged and the surface should be intact. 7.4 Storage
7.4.1 The product should be placed in a ventilated and dry place. It is strictly forbidden to contact with acids, alkalis, and salt substances, and prevent rain from soaking people. 7.4.2 The product cannot directly contact the ground, and the bottom should be raised by more than 100mm. Additional instructions:
This standard is proposed by the Standard and Quota Research Institute of the Ministry of Construction. This standard is under the jurisdiction of the China Building Standard Design Institute, the technical unit responsible for standardization of building products and equipment. This standard was drafted by the China Building Metal Structure Association (the main drafting unit), Shanxi Electronic Instrument Factory (Shanxi Automatic Door Company), and Suzhou Suxin Decoration Industry Corporation. The main drafters of this standard are Cui Yongfeng, Xu Zichang, Sun Junan, Jin Shunxing, and Tao Hongxing. This standard is entrusted to the China Building Standard Design Institute for interpretation. 9603 Sampling method and judgment rules:
For each project, no less than 50% shall be sampled, but the number of samples shall not be less than two. If all the inspection items are qualified, it is qualified. When one of them is unqualified, the sampling should be doubled. If the item is still unqualified, the batch is judged to be unqualified. All unqualified products should be repaired and can only be delivered after re-inspection. 6.2 Type inspection
6.2.1 Type inspection should be carried out in any of the following situations: a) Trial production and identification of new products or old products transferred to the factory for production; b) After normal production, when there are major changes in structure, materials, and processes that may affect product performance; c) During normal production, when continuous production is more than five years; d) When production is resumed after more than one year of suspension;
e) When the national quality supervision agency proposes a requirement for type inspection. 6.2.2 Type inspection items and judgment rules: Tests shall be carried out in accordance with the contents and requirements specified in Chapter 4 of this standard. 6.2.3 Sampling method:
3 samples are randomly selected from qualified products for type inspection. If all the inspection items are qualified, the batch is qualified. If one of them is unqualified, double sampling should be carried out. If the item is still unqualified, the batch is judged to be unqualified. Unqualified products are allowed to be returned for re-inspection.
7 Marking, packaging, transportation and storage
7.1 Marking
7.1.1 There should be a nameplate in a conspicuous part of the product, which should indicate: a) trademark and manufacturer's name;
b) product name;
c) product model,
d) manufacturing date or number.
7.1.2 The marking on the box surface of the packaging box should comply with the provisions of GB6388. 959
7.1.3 The packaging box should have words and signs such as "moisture-proof", "handle with care" and "upward", and the pattern should comply with the provisions of GB191.
7.2 Packaging
7.2.1 Products should be packaged with non-corrosive materials.7.2.2 The packaging box should have sufficient strength and be moisture-proof and shock-proof. 7.2.3 Products packed in the box should be guaranteed not to move with each other. 7.2.4 After the products are packed, the box must contain a packing list, product certificate, product instruction manual and warranty card. 7.3 Transportation
7.3.1 The means of transport should be rainproof and kept clean and free of dirt. 7.3.2 Products are strictly prohibited from falling or colliding during transportation and loading and unloading. The geometric shape of the product should remain unchanged and the surface should be intact. 7.4 Storage
7.4.1 The product should be placed in a ventilated and dry place. It is strictly forbidden to contact with acids, alkalis, and salt substances, and prevent rain from soaking people. 7.4.2 The product cannot directly contact the ground, and the bottom should be raised by more than 100mm. Additional instructions:
This standard is proposed by the Standard and Quota Research Institute of the Ministry of Construction. This standard is under the jurisdiction of the China Building Standard Design Institute, the technical unit responsible for standardization of building products and equipment. This standard was drafted by the China Building Metal Structure Association (the main drafting unit), Shanxi Electronic Instrument Factory (Shanxi Automatic Door Company), and Suzhou Suxin Decoration Industry Corporation. The main drafters of this standard are Cui Yongfeng, Xu Zichang, Sun Junan, Jin Shunxing, and Tao Hongxing. This standard is entrusted to the China Building Standard Design Institute for interpretation. 960
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.