title>JB/T 9852-1999 Hand-held pneumatic strapping and tightening machine - JB/T 9852-1999 - Chinese standardNet - bzxz.net
Home > JB > JB/T 9852-1999 Hand-held pneumatic strapping and tightening machine
JB/T 9852-1999 Hand-held pneumatic strapping and tightening machine

Basic Information

Standard ID: JB/T 9852-1999

Standard Name: Hand-held pneumatic strapping and tightening machine

Chinese Name: 手持式气动捆扎拉紧机

Standard category:Machinery Industry Standard (JB)

state:in force

Date of Release1999-06-28

Date of Implementation:2000-01-01

standard classification number

Standard ICS number:Mechanical Manufacturing>>Handheld Tools>>25.140.10 Pneumatic Tools

Standard Classification Number:Machinery>>Process Equipment>>J48 Pneumatic Tools

associated standards

alternative situation:ZB J48011-1989

Publication information

other information

Focal point unit:National Technical Committee for Standardization of Rock Drilling Machinery and Pneumatic Tools

Publishing department:National Technical Committee for Standardization of Rock Drilling Machinery and Pneumatic Tools

Introduction to standards:

JB/T 9852-1999 This standard is a revision of ZB J48 011-89 "32mm Handheld Pneumatic Strapping and Tensioning Machine". During the revision, the structural parameter indicators in the original standard were cancelled, and the applicability of the standard was improved. Other technical contents have not changed. This standard specifies the types and basic parameters, technical requirements, test methods, inspection rules and markings, packaging, transportation and storage of handheld pneumatic strapping and tensioning machines. This standard applies to handheld pneumatic strapping and tensioning machines. This standard was first issued in , first revised in , and second revised in . This is the th revision. JB/T 9852-1999 Handheld Pneumatic Strapping and Tensioning Machine JB/T9852-1999 Standard download decompression password: www.bzxz.net

Some standard content:

[CSZ5.140.10
Machinery Industry Standard of the People's Republic of China
JBT9852-1999
Hand-held pneumatic puller of strapping
Hand-held pneumatic puller of strapping1999-06-28 Issued
State Machinery Industry Bureau
2000-01-01 Implementation
JB/T9852—1999
This standard is a revision of ZBJ4801189 (32mm handheld pneumatic strapping and tightening machine). During the revision, the structural vertical index of the original standard was cancelled, and the standard's legacy was improved. The technical content has not changed. This standard will replace ZB3480119 from the date of this revision. This standard is proposed and managed by the National Standardization Technical Committee for Machinery and Pneumatic Tools. The drafting unit of this standard is Shanghai Pneumatic Tools Factory. The main drafters of this standard are Ke Hui and Gun Xiaoming. Scope
Machinery Industry Standard of the People's Republic of China
Handheld pneumatic strapping and tightening machine
Handheld pneumatic puller af strappingJB/T9852—1999
代4811.-89
This standard specifies the type and specification, technical requirements, test methods, inspection rules and marking, packaging, transportation and storage of pneumatic strapping tensioning machines.
Non-standard pneumatic strapping tensioning machines under pressure: 2 Reference standards
The provisions contained in the following standards become the provisions of this standard through reference in this standard: When this standard is published, the versions shown are valid. All standards will be revised, and the parties using this standard should explore the possibility of using the latest versions of the following standards, GB/T 2B281987
GB.T 5621.—1999
GB.T 5898—1986
JB.T 1590--1996
JE/T3576—1999
JB/T34—-1994
JB/T 404]-[994bZxz.net
JR/T 593T- J991
[R/T 761:1993
J 7162.-19 93
E/T 7163--199.1
/T7164—1993
JB/T7302-1994
JB/T 9857--1999
YH025—1992
3 Type and basic parameters
Reverse batch inspection and counting sampling procedures and selection tables (applicable to reverse inspection) Performance test methods for rock drilling machinery and pneumatic tools Channel sound measurement method for rock drilling machinery and pneumatic tools Engineering method Method for compiling product models of rock drilling machinery and pneumatic tools General technical conditions for rust prevention of rock drilling machinery and pneumatic tools General replacement conditions for metal molds and sand molds of rock drilling machines and pneumatic tools General detection method for cleanliness of rock drilling machinery and pneumatic tools General technical conditions for the quality of ash castings of rock drilling machinery Technical conditions
General technical conditions for heat treatment parts of pneumatic tools for rock drilling machineryGeneral technical conditions for steel investment castings of pneumatic tools for drilling machineryGeneral technical conditions for steel die forgings of Shouhong machinery and pneumatic toolsGeneral technical conditions for rock drilling machinery and pneumatic tools and their machined partsGeneral technical conditions for rock drilling machinery and pneumatic tools and their product packagingGeneral technical conditions for rock making machinery and pneumatic tools and their paintingSteel strip for packaging
31This machine is the tensioning machine among the pneumatic strapping machines, and the strapping machine is of separate type. 32 The basic parameters of the product shall comply with the provisions of the State Machinery Industry Bureau. Approved on June 28, 1999, and implemented on January 1, 2000. Specifications of belt width: 1. Width x original: 2. Tighten! 3.3 Product model shall be formulated in accordance with the provisions of JD, T1590. 4 Technical requirements tt||, variable gas consumption
noise, acoustic dynamic level!
4. Products should meet the requirements of the standard and be manufactured according to the drawings and technical documents approved by the prescribed procedures: acid gas
gas inner diameter
4.2 All military parts [including purchased parts, outsourced parts, standard parts) must be inspected and qualified by the quality inspection department before they can be installed: 4.3 The quality of castings meets the requirements of F593. 4.4 The quality of aluminum alloy castings shall meet the requirements of JB31904, 4.5 The quality of free-form castings shall meet the requirements of JB/T7162. 46 The quality of forgings shall comply with the provisions of the current 1.63 standard. 4.7 The quality of mechanical parts shall comply with the provisions of JD7164. 4.8 The quality of heat-treated cut parts shall comply with the provisions of JB/T7161. 4.9 The quality of product paint shall comply with the provisions of JB/T9857. 4.10 The quality of product anti-rust shall comply with the provisions of JB/T3576. 4.11 The technical performance of the steel work shall comply with the provisions of YB/T025. 4.12 The cleanliness of the product shall be measured according to the provisions of 3W
4.13 The assembly of the product shall be complete and accurate, and the parts shall be flexible and reliable. 4.14 For products of the same model, all parts shall be connected to each other. 4.15 The appearance of the product shall be neat and the color shall be uniform. 5 Test methods
5.1 The noise of the product shall be tested according to the heat of 5898. 5.2 The gas consumption of the product shall be tested according to the provisions of 5621. 5.3 The full inspection of the product shall be carried out in accordance with the provisions of H-4041. 5.4 The test of the tension force shall be carried out in accordance with the factory inspection procedures. 6 Inspection Regulations
6.1 The product shall be inspected and qualified by the inspection department of the factory and shall be accompanied by a product certificate before it can leave the factory. 2. Product factory inspection shall be carried out according to the inspection specifications formulated by the manufacturer based on the specific products, but the parameters of the whole wood of the product shall comply with the provisions of the table.
3. The cleanliness of the product is allowed to be inspected, and it shall be inspected at least once a month. 6.4. The product shall be subject to type inspection in the following circumstances: when the new product with reduced energy is subject to finalization appraisal; 2
JB/T9852--1999
b1. When the product has undergone a major change in design, process or material; when the product is discontinued for 2 years and then restarted; and when the products produced in batches or on a large scale are subject to inspection every 3.5 years. 6.5. The products subject to type inspection shall be randomly selected from the products that have passed the inspection. 6. Sampling inspection When inspecting the product quality, the normal inspection and sampling plan specified in G2828 shall be carried out? Marking, packaging, transportation and storage
7.1 The product components shall have the following markings:
a! Manufacturer name or trademark:
b Product model and trademark name:
eF Product number:
) Manufacturing date (year, month)
12 The packaging of the production station shall comply with the relevant regulations of JR302. 7.3 The product packaging shall be accompanied by the following technical documents: a) Product certificate:
5) Production manual:
Packing list.
7.4 The product shall be waterproof, moisture-proof and away from sunlight during transportation and production.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.