JB/T 9102.5-1999 JB/T 9102.5-1999 Metallic flat packings for reciprocating piston compressors Part 5: Extension springs for sealing rings and oil scraper rings JB/T9102.5-1999 Standard download decompression password: www.bzxz.net

EC5 23. 140
Machinery Industry Standard of the People's Republic of China
JB/T9102.1~9102.6-1999
Reciprocating piston compressor
Metal flat packing
Reciprocating piston compressor metal rectanglc packing1999-07-12Promulgated
National Machinery Industry Bureau
2000-01-01Implementation
JH/T91025-1999
This standard is a revision of J72005.5-Reciprocating piston compressor metal flat packing and oil scraper ring. The original standard was shortened and modified during the revision. The main technical content has not been changed. This standard is the fifth part of the JB/T92 series of standards for metal flat packings for differential piston compressors. The series of standards includes the following parts: Part 1: (i.e. JD/T9[02.1): Metal flat packings - three-dimensional sealing rings Part 2: (B9102.2): Metal flat packings - three-dimensional oil scraper rings - one and six sealing diagrams Part 3: (i.e. JB102.3): Metal mesh flat packings Part 4: (i.e. JB/U2.4): Metal mesh flat packings - two-diameter notched scraper rings Part 5: (i.e. JB/9102.5): Tensile springs for metal semi-metal packings - sealing rings and scraper rings Part 6: (i.e. J89102.6): Metallic flat packings for sealing and scraping pools according to technical conditions
This standard replaces J72005.3-87 from the date of implementation. This standard is proposed and managed by the National Technical Committee for Standardization of Machinery. The main drafting unit of this standard is Chengyang Compressor Factory. The main drafters of this standard are Zi Fujing, Feng Quanke, and Shen Mingyao. 21
Machinery Industry Standards of the People's Republic of China
Metallic flat packings for reciprocating piston compressors
Part 5: Tension springs for sealing and scraping oil conpresormetal rectaiglepacktngPart S: Tensile spring for saaling and wiper rings1Scope
JB/T 9102.5-1999
This standard specifies the type parameters and technical conditions of tensile spring tubes (hereinafter referred to as springs) for metal flat seals and wiper rings of reciprocating compressors.
This standard is applicable to Ratzer,
2Cited standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is revised, the ones shown or are valid. All standards will be revised, and the parties using this standard shall discuss the possibility of using the latest version of the following standards. GB/T1239.1—1989 Technical conditions for cold-rolled helical tension springsGB/T 2088—1997
3 Type, parameters
Size and number of the screw-in-tube (sodium ring pressure center type) 3.1 The type of the pull-out is GH. The model code in 2088-1997 is L, and the parameter name is GB/T1239.1. 3.3 The recommended number of the pull-out should comply with the provisions of Figure 1 and Table 1. Figure 1
Approved by Guohao Machinery Industry Bureau on July 12, 1999 22
Implementation on January 1, 2000 ||tt ||JB/T9102.5-1999bzxz.net
The initial tensile parts shall have a total length and a number of diameters.
4 Technical conditions
4.1 The control direction shall be specified as a whole
4.2 The limit deviation of tensile load, outer diameter and center length shall be in accordance with the 3-level accuracy requirements stipulated in GA 1239.1-1989. 4.3 The materials of tensile parts shall generally avoid Class C pressure-resistant springs. 4.4 The surface of the parts shall be hydrogenated.
4.5 The marking of the pull rod consists of the name, code, type, size and standard number. The marking system is as follows:
The pull rod with a material diameter d of 0.gmm, a pull rod middle diameter of 4mm and a free length H of 19mm is marked as LEB0.8×4n189JB/T9102.5—1999E
4.6 Other technical requirements, test methods, acceptance rules, packaging and marking, transportation and storage of pull rods shall be in accordance with the provisions of CBT1239.1.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.