This standard specifies the classification, technical requirements, test methods, inspection rules and marking, packaging, transportation and storage of paper barrels. This standard applies to the production, use, circulation and supervision and inspection of paper barrels. GB/T 14187-1993 Packaging container paper barrels GB/T14187-1993 standard download decompression password: www.bzxz.net
This standard specifies the classification, technical requirements, test methods, inspection rules and marking, packaging, transportation and storage of paper barrels. This standard applies to the production, use, circulation and supervision and inspection of paper barrels.

National Standard of the People's Republic of China
Packing container paper drum
Packing containcrs -Fibre drum 1 Content and scope of application
GB/T 14187-.-93
This standard specifies the classification, technical requirements, test methods, inspection rules and marking, packaging, transportation and storage of paper drums. This standard applies to the production, use, circulation and supervision inspection of paper drums. 2 References
(Xingnai 2828 Letter batch inspection counting sampling procedure and sampling table (applicable to continuous batch inspection) GB/T1857.3 Packaging transport package static load stacking test method table transport package drop test method
(G13/T4857.5 Packaging
3 Terms and symbols
3.1 Terms
3.1.1 Paper drum Fibrc drum
A rigid drum with a body made of paper or paperboard with adhesive and a bottom and cover made of the same material or other materials, with a positioning function between the bottom and the cover to form a storage container for reliable stacking. 3.1.2 Closure
Refers to the closing device of the container opening.
3.1.3 Drum hoop
A steel band ring with a concave ring groove rolled on it and fixed to the upper and lower mouths of the paper drum to enhance the strength of the paper drum. 3.2 Symbols
H—External height.
h—Inner height.
》)—Maximum outer diameter of the closure.
4 Product classification
4.1 Code
Approved by the State Administration of Technical Supervision on March 1, 1993 and implemented on August 1, 1993
:comZT
GB/T 14187—93
Maximum mass of paper barrel contents
Grade of paper barrel
Chinese pinyin for paper barrel: Ningtou
4.2 Grading
Paper barrels are divided into three grades according to their uses. Grade one barrels are used for export and packaging of heavy goods, grade two barrels are mainly used for transportation packaging of domestic products, and grade three barrels are mainly used for transportation packaging of short-distance and low-cost goods. 4.3 Varieties
Paper barrels are divided into 33 types according to their grading and maximum mass of contents, see Table 1. Table 1
Maximum mass of contents||tt ||4.4 Dimensions and structure
4.4.1 Dimensions
ZT1-10
ZT1-15
ZT1-20
ZT1-25
ZT1-30
ZT1-35
Z:T1-40
ZT1-50
ZT1-60
zr1-80
ZT1-100
ZT2-10
ZT2-15||tt ||ZT2-25
ZT2-30
2T2-35
ZT2-50
ZT2-60
ZT2-80
ZT2-100
Depending on the quality and size of the contents, the maximum outer diameter of the paper barrel closure should preferably be of the following sizes: Grade
zT3-10
ZT3-15
ZT3-20
ZT3-25
ZT3-30||tt| |ZT3-35
ZT3-40
ZT3-50
ZT3-60
ZT3-100
667,650,614,570,552,514,480,472,458,440,427,400,380,374,357,352,335,323,297.285.270,263,246,235,228,219,200,190. 4.4.2 The knot tree is shown in Figure 1.
5 Technical requirements
GB/T14187-93
Upper hoop: 4 barrel body?5-Lower hoop: 6-barrel bottom
1-barrel cover; 2-closer; 3
5.1 Products should be manufactured according to the drawings and technical documents approved by this standard and the prescribed procedures. 5.2 Appearance
5.2.1 Paper barrels should be round, without obvious defects such as loss of roundness, concave cancer, and deflection. 5.2.2 The handle is smooth, without mechanical damage, wrinkles, and debonding. The paint is evenly applied, without coating, bubbles, and obvious sagging. 5.2.3 The round curling edge has no paper tongue.
5.2.4 The barrel hoop is welded firmly and flatly, without burn-through or virtual welding, and without obvious rust, peeling and cracking. 5.2.5 The closure connection is solid and flexible, and the barrel cover and barrel body are well sealed after closing. 5.2.6 Galvanized barrel hoops and closures should be bright and not fall off. 5.2.7 Printed graphics and words should be clear and even, firmly attached, without any leakage. 5.2.8 The inside and outside of the paper barrel should be clean and oil-free.
5.3 Dimensions and deviations
The dimensions of the paper barrel should comply with the provisions of Article 4.4.1. The limit deviations of dimensions are shown in Table 2. Table 2
Limit deviations
5.4 Stacking performance
Maximum outer diameter of closure
Stacking load: 4900N for first-level paper barrels: 3900N for second-level paper barrels and 3400N for third-level paper barrels. It should not be full or broken for 24 hours, and the long-term deformation of water should not affect the stacking capacity of the paper barrel. 5.5 Drop resistance performance
GB/T 14187 --93
Drop height: 800mm for first-level paper barrel, 600mm for second-level paper barrel, and 400mm for third-level paper barrel. No leakage, no cracking, and no seal. 6 Test method
The following test is for the sample temperature pretreatment conditions: overflow 20±2℃, humidity (65±5)%; time 18h. For drop and stacking tests, the barrel should be filled with a mixture of dry sand and sawdust to 95% of the specified maximum mass and volume, and sealed. The temperature and humidity of the mixture are consistent with the sample pretreatment conditions.
6.1 Stacking test
Performed in accordance with GB/T 4857.3.
6.2 Drop test
Performed in accordance with GB/T4857.5. First, any point of the bottom edge of each barrel should be made to hit the ground; then, a point of the outer edge of the top surface of each barrel adjacent to the handle of the equalizer should be made to hit the ground. 7 Inspection rules
7.1 Products must be inspected and qualified by the quality inspection department of the production plant according to this standard before they can leave the factory. 7.2 Product inspection is divided into factory inspection and type inspection. The items are shown in Table 3. Table 3
Inspection classification
Factory inspection
Type inspection
7.3 Factory inspection
7.3.1 BatchbzxZ.net
The delivery batch of products of the same variety and specification is a batch. 7.3.2 Sampling plan
Appearance, size and deviation
All requirements
Carry out according to the normal inspection secondary sampling plan in GB2828, see Table 4. The transfer rules and the disposal after batch inspection shall comply with the provisions of 4.6.3 and 4.12 of GB2828. Table 4
Grouping number
Dimensions and tolerance
Note: For paper barrels used for packaging and cutting unit transportation, the maximum outer diameter of the closure is inspected one by one, and those that do not meet the standards cannot be used for packaging and unit transportation. 7.3.3 Sampling
Perform according to Article 4.9 of GB2828.
7.3.4 Determination
Perform according to Articles 4.11.1, 4.11.2, and 4.11.4 of GB2828. 7.4 Type inspection
7.4.1 Type inspection should be carried out in the following circumstances: a. When a new product or old product is transferred to the factory for trial production and identification; b.
After normal production, if there are major changes in materials, structure, and process that may affect product performance, it should be carried out once a year during normal production;
When production is resumed after a long-term suspension!
GB/T 14187-93
e. When there is a significant difference between the factory inspection results and the previous type inspection, the national quality supervision and inspection agency proposes a requirement for type inspection. f
7.4.2 Sampling plan and judgment rules
7.4.2.1 The sampling plan and judgment rules for the appearance, size and deviation inspection of paper barrels shall be carried out in accordance with Article 7.3. 7.4.2.2 The sampling plan and judgment rules for the stacking performance and drop performance inspection are shown in Table 5. Table 5
Stacking performance
Drop performance
Marking, packaging, transportation and storage
8.1 Marking
Sample size
The following markings should be printed on the paper barrels leaving the factory: manufacturer name, product name, production year and month, product code, qualified mark 8.2 Packaging
Package in pallets or negotiate with the user.
8.3 Transportation and storage
Products should be stored and transported away from rain, exposure, moisture and pollution, and should be protected from scratches by sharp objects. They should be stacked vertically, with the upper and lower openings aligned. Cross stacking is strictly prohibited. The height from the ground should be greater than 150mm when stored in the warehouse. Additional instructions:
This standard is proposed by China National Packaging Corporation.
This standard is under the jurisdiction of the Science and Education Department of China National Packaging Corporation. This standard is initiated by the Hebei Provincial Bureau of Standards and Metrology and Shijiazhuang Wood Products Factory No. 5. The main drafters of this standard are Cao Dongsheng, Fang Shoujing, Hua Guihai, Zhang Tao, Gou Jikang, Kang Li, Zhang Zhanshui, and Ge Jianmin.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.