Some standard content:
Subject content and applicable scope
Industry standards of the People's Republic of China
General technical conditions for toy dolls
This standard specifies the performance, technical requirements and test methods of toy dolls QB/T 1289--91
This standard applies to all kinds of non-animal dolls made of cloth, velvet, chemical fiber and other materials. Reference standards
GB6675 Toy safety
GB9832 Technical requirements for plush and cloth animal toys 3 Technical requirements
3.1 The shape, color, materials and clothing of the product shall comply with the technical conditions of the product. For the preparation of the technical conditions of individual products, please refer to Appendix A (supplement)
3.2 The soft products should be soft and the joints of the hard products should be loose and firm and not fall off. And they should comply with the action and posture requirements specified in the technical conditions of individual products. 3.3 Decorative parts, accessories and accessories should be complete and meet the technical conditions of individual products. .4 Pile, cloth products: The strength of the chain seam of the red part should meet the requirements of the table 1: Table 1
Warp tension (N)
After the chain is broken, the plush seam that does not meet the safety performance requirements may appear.
Cloth products, with fillings
3.5 The filling material must comply with the provisions of CB667513.1.4. 3.6 The product shall not be exposed.
Elastic parts are bright in color and have a strong skin texture. 3.8
Plastic parts are uniform in thickness, symmetrical and not deformed. 3.9
Plastic parts are well plasticized, not cracked, and have no shipping or stickiness. The key position of the hard plastic mold joint seam should be less than 1mm.
Hair is nailed (pasted) and fixed neatly, without exposing the bottom: Type 2
The flame retardancy of wool beards, wigs and masks shall comply with the provisions of 9.2 and 9.5 of GB6675. 3.12
3.13 The eyes should be bright, flexible, not stagnant or falling. Approved by the Ministry of Light Industry of the People's Republic of China on October 17, 1991, and implemented on June 1, 1992
QB/T 1289-91
TTKAoNiKAca=
3.14 Products with sound should be able to make a sound consistent with the seal, and the sound should not fall off, and mute sound is not allowed. 3.15 The clothes are clean and tidy, without stains, the clothes have no loose threads, no skipped stitches, the machine seams are not more than 1mm, and the stitches are not more than 2mm.
3.16 For products with external dimensions, the allowable deviation for speed above 300mm is ±10mm: the remaining allowable deviation is +5mm,
The surface coating of rouge, beard, etc. is firmly bonded. There is no stain, migration, diffusion, stickiness, or bottom exposure. 3.77
3.18 Name of external shape application points Table 2
Point name
Stain color point
Blowhole
Paint color
Chunpi white sacrifice
4Test method
20.5 or less 2 points
0.5 or less 1 point
20.5 dispersed by 1 5 points
! 0.5 or less 2 points
0.5 or less is not dense
80,5~1.0 1 point
Below 1.01 point
IgnoreBelow 0.52 points
Slightly filled
Dispersion is not obvious
4.1 Hard rest product joint assembly test is done by hand, and the feet and other parts are rotated at a speed of once per second. One should not fall off. Check whether it meets the requirements of Article 32. 4.2 Article 1 Test method Weld the force gauge with a diameter of 1910.5mm on the pliers, so that the human power and the measurement range are 150N, the accuracy is ±2 light or other force measuring devices with the same degree or above, electrical diagram 1 diagramwww.bzxz.net
QB/T 1289—91
The test is carried out at any position of the sample (see Figure 2). The seam of the test sample is taken as the center line, and the edges of the jaws are 13m away from the seam. During the test, the jaws must completely clamp the fabric. If the tested part cannot be completely clamped, change the position for the test. As shown in Figure 2, the tensile force specified in Articles 3 and 4 of this standard is uniformly applied within 59° in a direction perpendicular to the line and maintained for 16°. If the seam does not break during the test, but the textile fabric at the jaws breaks, the test is considered to have failed, and the cause should be found out and retested.
4.3 Inspection of plasticized quality of relatively thin materials: Cut the product with a knife, and the internal weave of the cross section should be fine and smooth without self-pointing. Fold it tightly in half once without breaking, and check whether it meets the requirements of Articles 3 and 9. 4.4 Inspection of flexibility Place the doll in a vertical position and rotate it 90° every 2 days, so that the doll rises and falls once (on the face of the tree). Observe whether the two eyes are flexible and synchronized, and whether they meet the requirements of Article 3.13. 4.5 Make the hair shaper sound 4 times in succession, and check whether there are any abnormal phenomena in Article 3.14 by comparing with the sealed sample. 4.6 Measure the appearance of the product with a steel tape measure with an accuracy of 200±1.2mm or other measuring tools with equal or higher accuracy. The inspection of the exposed thread of the chain can be measured with a ruler with an accuracy of 50±0.10mm or other measuring tools with equal or higher accuracy. 4.7 Inspection of the bonding fastness of the surface coating Wrap five layers of wet white plain cloth on a Tianhu weight of 500, and rub the inspection bundle back and forth three times at a speed of 3cm/. The coating does not fall off, and there should be no stain on the white cloth. Check whether it meets the requirements of Article 3.17. 4.8 Article 3.17 Inspection of coating migration and diffusion Place the product in a constant temperature oven at 40±2℃ for 4 hours. The coating on the surface should not migrate or diffuse. 4.9 Inspection of stains and external appearance of bottle spots Generally, observe with the naked eye. If necessary, use a 1x magnifying glass with an accuracy of 0.2mm to detect.
4.10 Check whether Articles 3.5 and 3.12 meet the requirements according to the relevant provisions of GB6675. 4.11 Appearance inspection should be carried out under natural light scattered from the north window, or under 40W fluorescent lamp lighting, observe with the naked eye, the distance between the product and the light source is about 1m, and the visual jump is 0.5m. Check whether Articles 3.1, 3.3, .6, 3.7, 3.8, and 3.11 meet the requirements. -1-
QB/T1289--91
Appendix A
General provisions for writing technical conditions of individual products (supplements)
iiKAoNiiKAca
A1 Technical conditions of individual products are necessary supplements to this standard for specific products, and their contents shall not conflict with the main items of this standard.
A2 The contents of technical conditions of individual products shall include modeling, color, materials, clothing, movements, etc. The technical standards of individual products shall be proposed by the supplier, and the ordering party may participate if necessary. A3
Additional remarks;
This standard was proposed by the Quality Standards Department of the Ministry of Light Industry. This standard was drafted by the Shanghai Toy Research Institute under the jurisdiction of the Jinguo Toy Standardization Center. The main drafter of this standard is Zhang Hailong.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.