JB/T 6551.1-1999 Woodworking planer parameters
Basic Information
Standard ID:
JB/T 6551.1-1999
Standard Name: Woodworking planer parameters
Chinese Name:
木工平压两用刨床 参数
Standard category:Machinery Industry Standard (JB)
state:in force
Date of Release1999-05-14
Date of Implementation:2000-01-01
standard classification number
Standard ICS number:Wood Technology >> Woodworking Equipment >> 79.120.10 Woodworking Machinery
Standard Classification Number:Machinery>>General Processing Machinery and Equipment>>J65 Woodworking Machine Tools and Machine Tools
Publication information
other information
Focal point unit:Fuzhou Woodworking Machine Tool Research Institute
Publishing department:Fuzhou Woodworking Machine Tool Research Institute
Introduction to standards:
JB/T 6551.1-1999 This standard is a revision of JB 3187-83 "Parameters of dual-purpose planers for woodworking and flat pressing". During the revision, only editorial modifications were made in accordance with relevant regulations, and the technical content has not changed. This standard specifies the parameters of dual-purpose planers for woodworking. This standard applies to woodworking machine tools with a maximum processing width of no more than 630mm. This standard was first published on February 21, 1983. JB/T 6551.1-1999 Woodworking planer parameters JB/T6551.1-1999 Standard download and decompression password: www.bzxz.net
Some standard content:
ICS79.120.10
J65
JB
Machinery Industry Standard of the People's Republic of China
JB/T6551.1-1999
Woodworking flat planer| |tt||1999-05-14 Release
National Machinery Industry Bureau
Parameters
2000-01-01 Implementation
Release
JB/T6551 .1—1999
Foreword
This standard is a revision of JB318783 "Wood T. Parameters of flat-pressing dual-purpose planer". During the revision, only editorial modifications were made in accordance with relevant regulations, and the technical content has not changed. .
This standard replaces JB3187-93 from the date of implementation. This standard was proposed by the National Woodworking Machine Tools and Tools Standardization Technical Committee. This standard is under the jurisdiction of Fuzhou Woodworking Machine Tool Research Institute. The unit responsible for drafting this standard: Shanxi Xixian Woodworking Machinery Factory. The main drafters of this standard: Zhang Feng and Feng Xiangming. This standard was first published on February 21, 1983. 2
Scope
Machinery Industry Standard of the People's Republic of China
Parameters of woodworking flat-pressing dual-purpose planers
This standard specifies the parameters of wood-T flat-pressing dual-purpose planers. This standard applies to woodworking planers with a maximum processing width of no more than 630mm. Parameters
JB/T6551.1-1999
generation JB3187-83
The type of wood T flat pressing dual-purpose planer is shown in Figure 1 and Figure 2 (the specific structure and Shape), the parameters should comply with the provisions of Table 1 Figure 1 without cuts
Figure 2 with cuts
Approved by the National Machinery Industry Bureau on 1999-05-14 and implemented on 2000-01-01||tt ||Parameter name
Maximum width 8 plus 1
mm
Pingchuang I workbench length
mm
Lifting height of front workbench||tt ||mm
Thickness of pressed parts
mm
Without loading port
With cutting
Maximum
Minimum||tt ||Minimum length of workpiece
mm
Maximum feed speed of planing
m/min
Cutting speed
m/s| |tt||200
100
JB/F6551.1—1999
Table 1
References
320
850|| tt||≥16.
≥120
≤5
200
≥12
>25
Note: Pingchuang work The length of the table can be appropriately lengthened according to user requirements. 400
6
number
>1400
≤250
≥16
500
≥160||tt ||26
630
>2300
≥200
≤10
300
24bzxz.net
>30| |tt||
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.