This standard specifies the product classification, technical requirements, test methods, inspection rules, marking and packaging of marine flange cast iron double-row stop valve boxes with flange connection dimensions in accordance with GB569 and GB2501. This standard is applicable to pipeline systems with seawater and fresh water as the medium. GB/T 2499-1993 Marine flange cast iron double-row stop valve boxes GB/T2499-1993 Standard download decompression password: www.bzxz.net
Some standard content:
1'D;629. 12- C1 : 621. 646. 2152 National Standard of the People's Republic of China GE/T 2499—93 Marine cast iron flange dual-raw slop valves-case1993-05-24 Issued State Bureau of Technical Supervision 1994-01-01 Implementation National Standard of the People's Republic of China Marine cast Tron Flange dual-row stop valve box valves-case1 Subject Content and Scope of Application GB/T2499-93 This standard specifies the product classification, installation requirements, testing, inspection regulations, labeling and packaging of marine flange cast double-row valve boxes (hereinafter referred to as valve boxes) with flange connection dimensions in accordance with GB569 and GB2501. This standard is applicable to pipeline systems with seawater and water as the medium. 2 Reference standards GB569 Marine flange connection dimensions and sealing surface GB2500 General technical conditions for pipeline valves GB2501 Marine flange connection dimensions and sealing surface (four-digit) GB3032 Marking of ship pipe fittings ZB/TU52001 Casting flange connection dimensions for cylinders 3 Product classification 3.1 The types of flanges are defined as follows: The connection dimensions are based on the two-way flange of GB569: RS type - flange connection dimensions are based on the two-way flange of GH2501; S type - flange connection dimensions are based on the three-way flange of GB560: SS type - flange connection dimensions are based on the three-way flange of GR2601. 3.2 The basic parameters of the valve box shall be in accordance with Table 1. 3.3 Structural dimensions of the valve box Nominal pressure P 3.3.1 The configuration and support positions of the valve box shall be in accordance with Figure 1 and Figure 2. 3.3.2 The structural dimensions of the valve box of R type shall be in accordance with Table 2. 3.3.3 The structural dimensions of the valve box of RS and SS types shall be in accordance with Table 3. Approved by the Technical Supervision and Sales Bureau on May 24, 1993, nominal diameter DN, /N, bzxz.net 40/50~~150/200 200/250~250/300 1994-01-01 actual bottle NM4b/o~Bn/tu GI/T 2499---93 ./LW, 10ry125 an/300 GR/T2499-93 alt oe public production CB/T 2499- International limit 3.4 Marking example GD/12499-93 Nominal pressure is 1.0MPa. Nominal diameter is DN, imm, DN80m. According to GB569 common flange connection size and sealing surface, the double-jointed marine flange effect is intended for double-holding condensation and stuffy box: brush box R10065/80GB/T2493-93 Nominal end 0. 6MPz, nominal diameter N, 200mm, ND, 25m. Three-way marine flange steel double row stop box with GB2501 flange connection dimensions and sealing surface (four-position): SS6200/250GB/T2499-93 4 Technical requirements and test methods 4.1 Technical requirements for box according to GB600 4.2 The main parts and materials of the box according to Table 4. Table 4 Parts name Aluminum system Paste system Stop the discussion 4.3 Method reverse connection dimensions and sealing installation GB569, GB2501. The wall thickness of the cage shall be in accordance with ZB/TU52001 4.5 Test method G600. 5 Inspection rules 5.1 Factory inspection 5.1.1 Each group of cages shall be inspected in succession and can only be shipped out after passing the inspection. 5.1.2 Inspection items shall be checked in accordance with Table 5. 5.2 Type inspection 5.2.1 Type inspection shall be carried out in the following cases: a. New products or old products are produced by the factory and the type is determined: Material Standard No. ZASn5 E-5 Take Sr.1021F 2QA15-2 After formal production, if the process is greatly changed, which may affect the product performance: When the national quality supervision agency proposes the requirement for type inspection, 5.2.2 Items of elastic compensation shall be in accordance with Table 5. GB9439 CB B83 GB4429 CB 883 6 Marking and packaging CB/T2499-93 Mechanical properties of express delivery, external reverse test Water resistance test 6.1 The marking of the bundle box shall be in accordance with GB3032 6.2 The packaging of the box shall be in accordance with GB600 Additional instructions: This standard is proposed by China Shipbuilding Industry Corporation. English 9 in accordance with GH 439, CRK83 Conforms to GBSGO This standard is also under the jurisdiction of the National Marine Machinery Standardization Technical Parts Committee Pipeline Annex Sub-Technical Committee. This standard was drafted by Jiangnan Shipyard, with participation from 603 Institute. The main drafters of this standard are Zhou Dexing and Lin Yizhun. The standard is provided with the unified drawing. Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.