GB 9334.1-1988 General provisions for shipboard radio frequency cables
Some standard content:
National Standard of the People's Republic of China
General provisions for shipboard radio frequency cables
Shipbaard radio-frequency cables GeneratorslGB 9334.1—8B
This standard adopts the provisions of IEC92—373 communication cables and radio frequency cables - shipboard flexible coaxial cables" 96 for radio frequency cables.
1 Scope of application
1.1 This standard is applicable to the connection of high-frequency host signals and asymmetric high-frequency signals to the ground on various river and sea vessels and various water structures such as offshore oil platforms. It is mainly used for the connection of radio and host equipment. 1.2 This standard should be used together with subsequent parts such as GB9334.2 and GB9334.3. 2 Reference standards
2.1 This standard references the valid versions of the following standards: GB2900
GB 2951
GB 3048
GB 4909
GI 4098
GB 3953
Electrical terminology
Test methods for physical and mechanical properties of wires and cablesTest methods for properties of wires and cables.
Test methods for operating loads
Test methods for terminals
Electrical line adjustment
GB 9331.1~,5
GE 4005
Delivery reels of power cables and wires for use above and below 0.6/1
JE3135
Silver-plated plastic copper wire
2.2 Other standards must be cited when the full term is specified in the corresponding certificate. 3 Definitions
3.1 The terms in this standard are explained in GE 2900. 3.2 RF conductor: RF cable conductor consists of an inner conductor and an outer conductor, both of which are used to connect the RF source and effectively transmit signals. 3.3 Solid dielectric: The space between the inner and outer conductors is filled with a dense dielectric, which can be made of a single material or a combination; the latter is made of two different materials concentrically bonded together. 3.4 Test
. Type test Code T Type test is a test conducted by the manufacturer before establishing a cable specified in the standard. The characteristic of type test is that it is generally not repeated after being done once. However, when the materials, structure and main processes used in the cable are changed, which affects the performance of the cable relay, the test must be repeated; or when otherwise specified in the product specification, such as regular testing, the test should also be repeated as required. b. Sampling test code s Sampling test is a test performed by the manufacturer on components of the whole cable sampled from the batch or specified rate and cut out from them. National Machinery Industry Association 198-05-23 Standard 1989-01-01 Implementation
We routine test routine. teat code RGB 9334.1--88
Routine test is a test conducted on all finished cable components. 35 Speed ratio
The ratio of the propagation speed of electricity in the cable to the propagation speed in the free space. The propagation speed in the free space is set at 299778 km/h,
4. Product naming and code
4.1 Code
4.1.1 Series code
Solid vinyl insulation series
Polyvinyl insulation series
4.1.2 Conductor code
4.1.3 Ground connection code
Polyvinyl oxide
Sheath code
Inner sheath, strand and outer sheath are as specified in Table 0; Code
Hao Xinyi
Note: 1) Tetraethylene terephthalate + acid glass braided wire for external transformer F 4.1.5 Characteristic code Characteristic impedance Insulation outer diameter 4.1.6 Structure code 42 indicates the product model, "characteristic impedance. Insulation outer diameter and standard code are indicated, GB 9334, structure code, insulation outer diameter reference, characteristic impedance parameter, protection code, ground code, series code, current technology, rated impedance parameter is indicated, nominal outer diameter parameter is indicated. Note: If it is a pulsed radiation conductor, the number of cores (2) and the conductor composition shall be indicated after the structure code. To distinguish it from the same RF conductor, 4.2.2 Example
1. Copper conductor solid polyethylene insulation bright vinyl inner bare steel wire braided full-cover coaxial radiation conductor, impedance 50. The nominal outer diameter is 7.25mm, and the outer conductor is a single-layer steel wire braided sheath, which is expressed as: CSYV9050-7-2GB9334.23
W. GB 9334.1-88
b. Chain-wound conductor is tetraethylene insulated ethylene oxide sheathed glass fiber filled braided slow ball jointed coaxial radiation conductor. And the impedance is 75N, the nominal outer diameter is 7.25mm, and the outer conductor is a single-layer silver-plated wire braided sheath, which is expressed as: CSFF75-7-11
5 Conductor 5.1 Structure 5.1.1 Inner conductor GH 9334,4. The structure shall comply with the provisions of Table [1]: Total diameter of inner conductor / standard diameter of solid core. Solid inner conductor shall not be welded again after one drawing. The maximum resistivity A-mz*/m shall not be greater than 1/m, and the distance between each welding point shall not be less than 300mm. The inner conductor can be welded by non-screw welding or annealing. The outer diameter of the joint shall not increase, and there shall be no protrusions or sharp protrusions. 51.2 Outer conductor, single metal wire sugar analog light. Specific structure 2 Provisions wife 2
Increase knowledge also
Edit job set
Be slow to thank sugar
Sex regulation change
Photography thank you
Digital model line
Plant inspection adjustment line
Start prototype machine screen different path back
7.25~ 11.5 | | tt | |tt||.16 ~ 0.18 | | tt | | 0.24 ~ 0.26 | | tt | | 0.24 ~ 0.26 | | tt | Or twisted joint, or inserted joint, the braided sleeve does not support the shoe body, b.
Increase the number of sets
Weaving
0.7~-0.95
0.70~0.95
0.70 ~0.93
0,70 ~0.95
W. The shrinkage is determined by the following formula:
GR 9334.1-88
Average diameter of braided layer (D=medium diameter+2d, d is the diameter of the full wire) mm;-weaving pitch
2. Filling factor K is determined by the following formula:
Number of metal wires per hole:
Height diameter of metal wire, mm;
-Number of crosses per unit length [the value above m is taken for calculation); the angle of inclination between the cable axis and the end braided strands. 5.2 Material
Copper wire should comply with GB 3953TR type.
Silver-plated steel wire shall meet the requirements of Table JB3135
5TRY type
Steel-clad steel wire shall meet the requirements of I3, the sintering shall be uniform, and its strength shall be consistent over the entire length. S
Computer system quantity "
Full conductor tensile strength
N/am*minimum
chaos. 1) This coefficient is the ratio of the total effective current resistance during the package adjustment period to the required DC resistance of the diameter adjustment. 6 Insulation
The nominal thickness and minimum thickness shall be specified in the subsequent standards. 6.2 Performance requirements
6.2.1 Physical and mechanical properties shall comply with the relevant provisions of Article 8 of this standard. 1.2.2 The insulation shall be tightly wrapped around the inner conductor,? Protective
71 type
As specified in bag 4.
250 mm Test swelling rate
W. Class
Non-metallic protective film
Metallic protective layer
72 Extruded protective film
GB 9334.1--88
-Polyvinyl chloride protective film
-40 Seven-pass avoidance element ethylene-carbon sheath
Ethylene screw flame retardant metal + glass fiber woven dyed silicon controlled non-metallic inner sheath + zinc-coated new aluminum sheath
7,2.1 The nominal thickness and minimum thickness should be determined in the standards of each town. 1.2.2 The sheath is black, with a flat surface, no air filter and holes in the cross section, and is filled with light plate weaving. 7.3 Braided sheath
7.3.1 The nominal thickness and minimum thickness of the combined body shall be specified in the subsequent standards.
Heat-tightness insulation
Burning memory
7.3.2 The woven layer shall be densely packed, and the glass fiber braided layer shall be covered with silicone organic seal. The filling coefficient of the braided layer shall be calculated according to the standard formula (2) and shall not be less than 0.6.
The zinc-coated steel wire braided layer shall be able to withstand the film continuity test in Appendix G of GB 9331.1. 7.4.2 The weaving shall be uniform and the surface shall be flat. The wiring harness is not allowed to be replaced, connected or overlapped. Metal joints should not be exposed during overlapping. 4.3 The installation layer should be repeated. 8 Finished cable 8.1 The resistivity of the conductor specified in the cable standard shall comply with the provisions of Article 3 of this standard.
83 Insulation resistance
At 20 ℃, the insulation resistance between the inner and outer conductors should not be less than 5 000 M2;km.8.4
Insulation withstand voltage performance
According to the requirements of installation 5,
W. Nominal outer diameter of ground screw
3,0~44
7.25~10.0
Electrode sheath withstand voltage performance
GE 9334.1—88
Characteristic plastic resistance
Test voltage kV
Should be able to withstand the hardness test voltage kV The specified water burst test, sensitive test, covering thickness 6
0.5≤1,≤0.8
corona test
recovery test
test voltage setting V
no-destruction voltage value is specified in the various government standards
the attenuation constant should be specified in the various regional standards.
Characteristic resistance
shall be specified in the subsequent standards,
heating test
shall be specified in Table 7,
sheath type
oxygen protection
duration m
test nature
prohibition time
spark spot plug
test voltage upper V
no acid
all click time 2
test results
decrease/
specified by the subsequent standards
W.8,10 heating specification test
GB 9334.1--88
shall be able to withstand the decay 8 Specified heating after rolling test. Table
Electric change protection pot
Glazed protection
Solid protection product
200±5
Outer diameter of sample protection product.
Good 11 High temperature after cold bending test
Test support diameter mm
Number of bending
Smin [0 times
min 10 times
Test results
The end of the screw and the sheath shall
No mechanical damage
Electric should be able to withstand the high temperature after the maximum exposure specified in Table 9. After the test, the end of the sample and the sheath shall have no mechanical damage during the test. The electric sugar is first exposed to the high temperature for a specified time, then cooled in a self-cooling case for 1 E, and then exposed to the low temperature for a specified time. Then roll the system on a test rod of specified diameter. Electrostatic protection
Holy gas jacket
Polytetraoxyethylene
Electrophilic
High overflow
250±5
Time h
Maximum resistance
8.12 Low temperature narrow bend test
The electrostatic duct shall be able to pass the specified low temperature bend test for 10 min. Time
Direct dyeing time
With current national effect
Rod outer diameter
12.7mm or 3 Figure
Specimen outer diameter
D212.7mm【Figure
Light test test release of inert gas and inorganic cutting injury. Table 10
Protection type
New B explosion transformer
With tetraethylene oxide electric worry
8.13 Flowability test
Test place
On
The electric fuel shall be able to withstand the flowability test specified in Table 11, Bin static outer diameter mm
Product number
D 12.7 mm or 3 ;
D≥12.7mm[
W. Test thickness
100±2
8.14 Identification mark
GB 9334.1-B8
Reading time
In the standard
Absolute position % Not more than
The identification mark of the electric jump shall comply with the provisions of GB 6995.3. The content of the mark shall be the manufacturer's name and trademark, certification mark and model. 8.15 Special performance
If required, it shall be specified in the subsequent standards. 9 Delivery length
The delivery length of solid polyethylene insulation shall not be less than 100m, and the short section shall not be less than 10m. The delivery length of solid polyurethane insulation shall not be less than 45m, and the short section shall not be less than 3m. The delivery quantity of short-length cables shall not exceed 13% of the total length of the delivery. According to the agreement between the two parties, cables of any length can be delivered. The error of length measurement shall not exceed ±0.5%.
10 Test and acceptance
10.1 Products shall be inspected and supervised by the technical inspection department of the manufacturer before delivery. Products shall be accompanied by a product inspection certificate. 10.2 Products shall be tested according to the following provisions. Type test items: all performance items specified in the standard. b. Sampling test items: conductor structure, insulation, sheath and insulation size, low temperature performance of ethylene oxide sheath, chemical test film of armored steel wire coating. Routine test items: insulation resistance, voltage test, corona test, capacitance constant, characteristic impedance. 10.3 Sampling test: samples shall be taken from the delivery batch, and the sampling quantity shall be based on the agreement between the two parties. If the user does not raise any objection, sampling shall be carried out according to the manufacturer's regulations. If the first sampling fails, another package shall be taken for continuous sampling and a second test shall be conducted on the unqualified items. If it still fails, the test shall be considered unqualified. 10.4 Test methods 10.4.1 General test methods shall comply with the relevant test method standards and be specified in subsequent standards. 10.4.2 Special test methods shall be specified in relevant standards. 11 Packaging 11.1 Cables shall be delivered in drums or in drawings and neatly packed. Cable heads shall be sealed. Cable drums shall comply with the provisions of GB 4004 and GB 4005. The inner radius shall not be less than the allowable bending radius in the cable shrinkage chamber. 11.2 Each package shall be attached with a label and marked: Manufacturer's name or trademark:
b. Product model specification:
Length, mm
Wd,
e, manufacturing date, year, month:
Standard number or certification mark
2. Correct rotation direction of the switch,
11.3 When packing, the outer cover of the box should be marked with:, Manufacturer's name or trademark:
b. Product model specification:
: Certification mark:
d, body size and weight,
Moisture-proof and heat-proof mark.
GB 9334.1-88
W.1--88
-Station test to polyvinyl chloride leak
-40 seven for the protection of the element ethylene explosion sheath
pro-four benefits ethylene screw Sa combustion metal + glass fiber woven dyed silicon control non-metallic inner sleeve + belly zinc tonality new aluminum
7,2.1 The nominal thickness and minimum thickness should be determined in the subsequent standards. 1.2.2 The sheath is black, the surface is flat, the cross section has no air filter and holes, etc., and the ring has a light plate weaving speed. 7.3 I wrap a braided protective strength
7.3.1 The nominal thickness and minimum thickness of the combination are specified in the subsequent standards, saying
heat-tightening protective pain
burning memory-braided protective
7.3.2 The element ethylene film sheath should be densely packed, and the glass fiber braided layer should be covered with a silicon organic seal. The filling coefficient of the braided layer shall be calculated according to the standard formula (2) and shall not be less than 0.6.7.4.1 The braided layer shall be filled with 0.30 mm zinc-plated steel wire outside the sheath. The filling coefficient of the braided layer shall be calculated according to the standard formula (2) and shall not be less than 0.6.7.4.2 The braiding shall be uniform and the surface shall be flat. The braided layer shall not be spliced, connected or overlapped. The metal joints shall not be exposed during overlap.7.3 The braided layer shall be free of break. 8 Finished cable 8.1 Cable external control The resistivity of the conductor specified in each standard shall comply with the provisions of Article 3 of this standard. 83 Insulation resistance The insulation resistance between the inner and outer conductors at 20°C shall not be less than 5 000 M2;km. 8.4 Insulation withstand voltage performance According to the provisions of the installation 5, W. Nominal outer diameter of the ground screw 3,0~44 7.25~10.0 Latex sheath withstand voltage performance GE 9334.1—88 Characteristic plastic resistance test voltage kV Should be able to withstand the hardness test voltage kV The specified water burst test, sensitive test, covering thickness 6
0.5≤1,≤0.8
corona test
recovery test
test voltage setting V
no-destruction voltage value is specified in the various government standards
the attenuation constant should be specified in the various regional standards.
Characteristic resistance
shall be specified in the subsequent standards,
heating test
shall be specified in Table 7,
sheath type
oxygen protection
duration m
test nature
prohibition time
spark spot plug
test voltage upper V
no acid
all click time 2
test results
decrease/
specified by the subsequent standards
W.8,10 heating specification test
GB 9334.1--88
shall be able to withstand the decay 8 Specified heating after rolling test. Table
Electric change protection pot
Glazed protection
Solid protection product
200±5
Outer diameter of sample protection product.
Good 11 High temperature after cold bending test
Test support diameter mm
Number of bending
Smin [0 times
min 10 times
Test results
The end of the screw and the sheath shall
No mechanical damage
Electric should be able to withstand the high temperature after the maximum exposure specified in Table 9. After the test, the end of the sample and the sheath shall have no mechanical damage during the test. The electric sugar is first exposed to the high temperature for a specified time, then cooled in a self-cooling case for 1 E, and then exposed to the low temperature for a specified time. Then roll the system on a test rod of specified diameter. Electrostatic protection
Holy gas jacket
Polytetraoxyethylene
Electrophilic
High overflow
250±5
Time h
Maximum resistance
8.12 Low temperature narrow bend test
The electrostatic duct shall be able to pass the specified low temperature bend test for 10 min. Time
Direct dyeing time
With current national effect
Rod outer diameter
12.7mm or 3 Figure
Specimen outer diameter
D212.7mm【Figure
Light test test release of inert gas and inorganic cutting injury. Table 10
Protection type
New B explosion transformer
With tetraethylene oxide electric worry
8.13 Flowability test
Test place
On
The electric fuel shall be able to withstand the flowability test specified in Table 11, Bin static outer diameter mm
Product number
D 12.7 mm or 3 ;
D≥12.7mm[
W. Test thickness
100±2
8.14 Identification mark
GB 9334.1-B8
Reading time
In the standard
Absolute position % Not more than
The identification mark of the electric jump shall comply with the provisions of GB 6995.3. The content of the mark shall be the manufacturer's name and trademark, certification mark and model. 8.15 Special performance
If required, it shall be specified in the subsequent standards. 9 Delivery length
The delivery length of solid polyethylene insulation shall not be less than 100m, and the short section shall not be less than 10m. The delivery length of solid polyurethane insulation shall not be less than 45m, and the short section shall not be less than 3m. The delivery quantity of short-length cables shall not exceed 13% of the total length of the delivery. According to the agreement between the two parties, cables of any length can be delivered. The error of length measurement shall not exceed ±0.5%.
10 Test and acceptance
10.1 Products shall be inspected and supervised by the technical inspection department of the manufacturer before delivery. Products shall be accompanied by a product inspection certificate. 10.2 Products shall be tested according to the following provisions. Type test items: all performance items specified in the standard. b. Sampling test items: conductor structure, insulation, sheath and insulation size, low temperature performance of ethylene oxide sheath, chemical test film of armored steel wire coating. Routine test items: insulation resistance, voltage test, corona test, capacitance constant, characteristic impedance. 10.3 Sampling test: samples shall be taken from the delivery batch, and the sampling quantity shall be based on the agreement between the two parties. If the user does not raise any objection, sampling shall be carried out according to the manufacturer's regulations. If the first sampling fails, another package shall be sampled and the unqualified items shall be tested for the second time. If they still fail, the test shall be considered unqualified. 10.4 Test methods 10.4.1 General test methods shall comply with the relevant test method standards and be specified in subsequent standards. 10.4.2 Special test methods shall be specified in relevant standards. 11 Packaging 11.1 Cables shall be delivered in drums or in drawings and neatly packed. Cable heads shall be sealed. Cable drums shall comply with the provisions of GB 4004 and GB 4005. The inner radius shall not be less than the allowable bending radius in the cable shrinkage chamber. 11.2 Each package shall be attached with a label and marked: Manufacturer's name or trademark:
b. Product model specification:
Length, mm
Wd,
e, manufacturing date, year, month:
Standard number or certification mark
2. Correct rotation direction of the switch,
11.3 When packing, the outer cover of the box should be marked with:, Manufacturer's name or trademark:
b. Product model specification:
: Certification mark:
d, body size and weight,
Moisture-proof and heat-proof mark.
GB 9334.1-88
W.1--88
-Station test to polyvinyl chloride leak
-40 seven for the protection of the element ethylene explosion sheath
pro-four benefits ethylene screw Sa combustion metal + glass fiber woven dyed silicon control non-metallic inner sleeve + belly zinc tonality new aluminum
7,2.1 The nominal thickness and minimum thickness should be determined in the subsequent standards. 1.2.2 The sheath is black, the surface is flat, the cross section has no air filter and holes, etc., and the ring has a light plate weaving speed. 7.3 I wrap a braided protective strength
7.3.1 The nominal thickness and minimum thickness of the combination are specified in the subsequent standards, saying
heat-tightening protective pain
burning memory-braided protective
7.3.2 The element ethylene film sheath should be densely packed, and the glass fiber braided layer should be covered with a silicon organic seal. The filling coefficient of the braided layer shall be calculated according to the standard formula (2) and shall not be less than 0.6.7.4.1 The braided layer shall be filled with 0.30 mm zinc-plated steel wire outside the sheath. The filling coefficient of the braided layer shall be calculated according to the standard formula (2) and shall not be less than 0.6.7.4.2 The braiding shall be uniform and the surface shall be flat. The braided layer shall not be spliced, connected or overlapped. The metal joints shall not be exposed during overlap.7.3 The braided layer shall be free of break. 8 Finished cable 8.1 Cable external control The resistivity of the conductor specified in each standard shall comply with the provisions of Article 3 of this standard. 83 Insulation resistance The insulation resistance between the inner and outer conductors at 20°C shall not be less than 5 000 M2;km. 8.4 Insulation withstand voltage performance According to the provisions of the installation 5, W. Nominal outer diameter of the ground screw 3,0~44 7.25~10.0 Latex sheath withstand voltage performance GE 9334.1—88 Characteristic plastic resistance test voltage kV Should be able to withstand the hardness test voltage kV The specified water burst test, sensitive test, covering thickness 6
0.5≤1,≤0.8
corona test
recovery test
test voltage setting V
no-destruction voltage value is specified in the various government standards
the attenuation constant should be specified in the various regional standards.
Characteristic resistance
shall be specified in the subsequent standards,
heating test
shall be specified in Table 7,
sheath type
oxygen protection
duration m
test nature
prohibition time
spark spot plug
test voltage upper V
no acid
all click time 2
test results
decrease/
specified by the subsequent standards
W.8,10 heating specification test
GB 9334.1--88
shall be able to withstand the decay 8 Specified heating after rolling test. Table
Electric change protection pot
Glazed protection
Solid protection product
200±5
Outer diameter of sample protection product.
Good 11 High temperature after cold bending test
Test support diameter mm
Number of bending
Smin [0 times
min 10 times
Test results
The end of the screw and the sheath shall
No mechanical damage
Electric should be able to withstand the high temperature after the maximum exposure specified in Table 9. After the test, the end of the sample and the sheath shall have no mechanical damage during the test. The electric sugar is first exposed to the high temperature for a specified time, then cooled in a self-cooling case for 1 E, and then exposed to the low temperature for a specified time. Then roll the system on a test rod of specified diameter. Electrostatic protection
Holy gas jacket
Polytetraoxyethylene
Electrophilic
High overflow
250±5
Time h
Maximum resistance
8.12 Low temperature narrow bend test
The electrostatic duct shall be able to pass the specified low temperature bend test for 10 min. Time
Direct dyeing time
With current national effect
Rod outer diameter
12.7mm or 3 Figure
Specimen outer diameter
D212.7mm【Figure
Light test test release of inert gas and inorganic cutting injury. Table 10
Protection type
New B explosion transformer
With tetraethylene oxide electric worry
8.13 Flowability test
Test place
On
The electric fuel shall be able to withstand the flowability test specified in Table 11, Bin static outer diameter mm
Product number
D 12.7 mm or 3 ;
D≥12.7mm[
W. Test thickness
100±2
8.14 Identification mark
GB 9334.1-B8
Reading time
In the standard
Absolute position % Not more than
The identification mark of the electric jump shall comply with the provisions of GB 6995.3. The content of the mark shall be the manufacturer's name and trademark, certification mark and model. 8.15 Special performance
If required, it shall be specified in the subsequent standards. 9 Delivery length
The delivery length of solid polyethylene insulation shall not be less than 100m, and the short section shall not be less than 10m. The delivery length of solid polyurethane insulation shall not be less than 45m, and the short section shall not be less than 3m. The delivery quantity of short-length cables shall not exceed 13% of the total length of the delivery. According to the agreement between the two parties, cables of any length can be delivered. The error of length measurement shall not exceed ±0.5%.
10 Test and acceptance
10.1 Products shall be inspected and supervised by the technical inspection department of the manufacturer before delivery. Products shall be accompanied by a product inspection certificate. 10.2 Products shall be tested according to the following provisions. Type test items: all performance items specified in the standard. b. Sampling test items: conductor structure, insulation, sheath and insulation size, low temperature performance of ethylene oxide sheath, chemical test film of armored steel wire coating. Routine test items: insulation resistance, voltage test, corona test, capacitance constant, characteristic impedance. 10.3 Sampling test: samples shall be taken from the delivery batch, and the sampling quantity shall be based on the agreement between the two parties. If the user does not raise any objection, sampling shall be carried out according to the manufacturer's regulations. If the first sampling fails, another package shall be sampled and the unqualified items shall be tested for the second time. If they still fail, the test shall be considered unqualified. 10.4 Test methods 10.4.1 General test methods shall comply with the relevant test method standards and be specified in subsequent standards. 10.4.2 Special test methods shall be specified in relevant standards. 11 Packaging 11.1 Cables shall be delivered in drums or in drawings and neatly packed. Cable heads shall be sealed. Cable drums shall comply with the provisions of GB 4004 and GB 4005. The inner radius shall not be less than the allowable bending radius in the cable shrinkage chamber. 11.2 Each package shall be attached with a label and marked: Manufacturer's name or trademark:
b. Product model specification:
Length, mm
Wd,
e, manufacturing date, year, month:
Standard number or certification mark
2. Correct rotation direction of the switch,
11.3 When packing, the outer cover of the box should be marked with:, Manufacturer's name or trademark:
b. Product model specification:
: Certification mark:
d, body size and weight,
Moisture-proof and heat-proof mark.
GB 9334.1-88
W.4 Galvanized wire braided micro-jacketed sheath
7.4.1 The outer sheath is covered with 0.30 mm thick galvanized steel wire. The filling coefficient of the braided layer shall be calculated according to formula (2) of this standard and shall not be less than 0.6.
The zinc-coated steel wire braided micro-jacketed sheath shall be able to withstand the film continuity test in Appendix G of GB 9331.1. 7.4.2 The braiding shall be uniform and the surface shall be flat. The braided wire shall not be spliced, connected or overlapped. The metal joints shall not be exposed during overlap.
|4.3 The braided layer shall be free of breakage. 8 Finished cable
8.1 The resistivity of the conductor specified in the cable standard shall comply with the provisions of Article 3 of this standard.
83 Insulation resistance
At 20 ℃, the insulation resistance between the inner and outer conductors should not be less than 5 000 M2;km.8.4
Insulation withstand voltage performance
According to the requirements of installation 5,
W. Nominal outer diameter of ground screw
3,0~44
7.25~10.0
Electrode sheath withstand voltage performance
GE 9334.1—88
Characteristic plastic resistance
Test voltage kV
Should be able to withstand the hardness test voltage kV The specified water burst test, sensitive test, covering thickness 6
0.5≤1,≤0.8
corona test
recovery test
test voltage setting V
no-destruction voltage value is specified in the various government standards
the attenuation constant should be specified in the various regional standards.
Characteristic resistance
shall be specified in the subsequent standards,
heating test
shall be specified in Table 7,
sheath type
oxygen protection
duration m
test nature
prohibition time
spark spot plug
test voltage upper V
no acid
all click time 2
test results
decrease/
specified by the subsequent standards
W.8,10 heating specification test
GB 9334.1--88
shall be able to withstand the decay 8 Specified heating after rolling test. Table
Electric change protection pot
Glazed protection
Solid protection product
200±5
Outer diameter of sample protection product.
Good 11 High temperature after cold bending test
Test support diameter mm
Number of bending
Smin [0 times
min 10 times
Test results
The end of the screw and the sheath shall
No mechanical damage
Electric should be able to withstand the high temperature after the maximum exposure specified in Table 9. After the test, the end of the sample and the sheath shall have no mechanical damage during the test. The electric sugar is first exposed to the high temperature for a specified time, then cooled in a self-cooling case for 1 E, and then exposed to the low temperature for a specified time. Then roll the system on a test rod of specified diameter. Electrostatic protection
Holy gas jacket
Polytetraoxyethylene
Electrophilic
High overflow
250±5
Time h
Maximum resistance
8.12 Low temperature narrow bend test
The electrostatic duct shall be able to pass the specified low temperature bend test for 10 min. Time
Direct dyeing time
With current national effect
Rod outer diameter
12.7mm or 3 Figure
Specimen outer diameter
D212.7mm【Figure
Light test test release of inert gas and inorganic cutting injury. Table 10
Protection type
New B explosion transformer
With tetraethylene oxide electric worry
8.13 Flowability testwww.bzxz.net
Test place
On
The electric fuel shall be able to withstand the flowability test specified in Table 11, Bin static outer diameter mm
Product number
D 12.7 mm or 3 ;
D≥12.7mm[
W. Test thickness
100±2
8.14 Identification mark
GB 9334.1-B8
Reading time
In the standard
Absolute position % Not more than
The identification mark of the electric jump shall comply with the provisions of GB 6995.3. The content of the mark shall be the manufacturer's name and trademark, certification mark and model. 8.15 Special performance
If required, it shall be specified in the subsequent standards. 9 Delivery length
The delivery length of solid polyethylene insulation shall not be less than 100m, and the short section shall not be less than 10m. The delivery length of solid polyurethane insulation shall not be less than 45m, and the short section shall not be less than 3m. The delivery quantity of short-length cables shall not exceed 13% of the total length of the delivery. According to the agreement between the two parties, cables of any length can be delivered. The error of length measurement shall not exceed ±0.5%.
10 Test and acceptance
10.1 Products shall be inspected and supervised by the technical inspection department of the manufacturer before delivery. Products shall be accompanied by a product inspection certificate. 10.2 Products shall be tested according to the following provisions. Type test items: all performance items specified in the standard. b. Sampling test items: conductor structure, insulation, sheath and insulation size, low temperature performance of ethylene oxide sheath, chemical test film of armored steel wire coating. Routine test items: insulation resistance, voltage test, corona test, capacitance constant, characteristic impedance. 10.3 Sampling test: samples shall be taken from the delivery batch, and the sampling quantity shall be based on the agreement between the two parties. If the user does not raise any objection, sampling shall be carried out according to the manufacturer's regulations. If the first sampling fails, another package shall be sampled and the unqualified items shall be tested for the second time. If they still fail, the test shall be considered unqualified. 10.4 Test methods 10.4.1 General test methods shall comply with the relevant test method standards and be specified in subsequent standards. 10.4.2 Special test methods shall be specified in relevant standards. 11 Packaging 11.1 Cables shall be delivered in drums or in drawings and neatly packed. Cable heads shall be sealed. Cable drums shall comply with the provisions of GB 4004 and GB 4005. The inner radius shall not be less than the allowable bending radius in the cable shrinkage chamber. 11.2 Each package shall be attached with a label and marked: Manufacturer's name or trademark:
b. Product model specification:
Length, mm
Wd,
e, manufacturing date, year, month:
Standard number or certification mark
2. Correct rotation direction of the switch,
11.3 When packing, the outer cover of the box should be marked with:, Manufacturer's name or trademark:
b. Product model specification:
: Certification mark:
d, body size and weight,
Moisture-proof and heat-proof mark.
GB 9334.1-88
W.4 Galvanized wire braided micro-jacketed sheath
7.4.1 The outer sheath is covered with 0.30 mm thick galvanized steel wire. The filling coefficient of the braided layer shall be calculated according to formula (2) of this standard and shall not be less than 0.6.
The zinc-coated steel wire braided micro-jacketed sheath shall be able to withstand the film continuity test in Appendix G of GB 9331.1. 7.4.2 The braiding shall be uniform and the surface shall be flat. The braided wire shall not be spliced, connected or overlapped. The metal joints shall not be exposed during overlap.
|4.3 The braided layer shall be free of breakage. 8 Finished cable
8.1 The resistivity of the conductor specified in the cable standard shall comply with the provisions of Article 3 of this standard.
83 Insulation resistance
At 20 ℃, the insulation resistance between the inner and outer conductors should not be less than 5 000 M2;km.8.4
Insulation withstand voltage performance
According to the requirements of installation 5,
W. Nominal outer diameter of ground screw
3,0~44
7.25~10.0
Electrode sheath withstand voltage performance
GE 9334.1—88
Characteristic plastic resistance
Test voltage kV
Should be able to withstand the hardness test voltage kV The specified water burst test, sensitive test, covering thickness 6
0.5≤1,≤0.8
corona test
recovery test
test voltage setting V
no-destruction voltage value is specified in the various government standards
the attenuation constant should be specified in the various regional standards.
Characteristic resistance
shall be specified in the subsequent standards,
heating test
shall be specified in Table 7,
sheath type
oxygen protection
duration m
test nature
prohibition time
spark spot plug
test voltage upper V
no acid
all click time 2
test results
decrease/
specified by the subsequent standards
W.8,10 heating specification test
GB 9334.1--88
shall be able to withstand the decay 8 Specified heating after rolling test. Table
Electric change protection pot
Glazed protection
Solid protection product
200±5
Outer diameter of sample protection product.
Good 11 High temperature after cold bending test
Test support diameter mm
Number of bending
Smin [0 times
min 10 times
Test results
The end of the screw and the sheath shall
No mechanical damage
Electric should be able to withstand the high temperature after the maximum exposure specified in Table 9. After the test, the end of the sample and the sheath shall have no mechanical damage during the test. The electric sugar is first exposed to the high temperature for a specified time, then cooled in a self-cooling case for 1 E, and then exposed to the low temperature for a specified time. Then roll the system on a test rod of specified diameter. Electrostatic protection
Holy gas jacket
Polytetraoxyethylene
Electrophilic
High overflow
250±5
Time h
Maximum resistance
8.12 Low temperature narrow bend test
The electrostatic duct shall be able to pass the specified low temperature bend test for 10 min. Time
Direct dyeing time
With current national effect
Rod outer diameter
12.7mm or 3 Figure
Specimen outer diameter
D212.7mm【Figure
Light test test release of inert gas and inorganic cutting injury. Table 10
Protection type
New B explosion transformer
With tetraethylene oxide electric worry
8.13 Flowability test
Test place
On
The electric fuel shall be able to withstand the flowability test specified in Table 11, Bin static outer diameter mm
Product number
D 12.7 mm or 3 ;
D≥12.7mm[
W. Test thickness
100±2
8.14 Identification mark
GB 9334.1-B8
Reading time
In the standard
Absolute position % Not more than
The identification mark of the electric jump shall comply with the provisions of GB 6995.3. The content of the mark shall be the manufacturer's name and trademark, certification mark and model. 8.15 Special performance
If required, it shall be specified in the subsequent standards. 9 Delivery length
The delivery length of solid polyethylene insulation shall not be less than 100m, and the short section shall not be less than 10m. The delivery length of solid polyurethane insulation shall not be less than 45m, and the short section shall not be less than 3m. The delivery quantity of short-length cables shall not exceed 13% of the total length of the delivery. According to the agreement between the two parties, cables of any length can be delivered. The error of length measurement shall not exceed ±0.5%.
10 Test and acceptance
10.1 Products shall be inspected and supervised by the technical inspection department of the manufacturer before delivery. Products shall be accompanied by a product inspection certificate. 10.2 Products shall be tested according to the following provisions. Type test items: all performance items specified in the standard. b. Sampling test items: conductor structure, insulation, sheath and insulation size, low temperature performance of ethylene oxide sheath, chemical test film of armored steel wire coating. Routine test items: insulation resistance, voltage test, corona test, capacitance constant, characteristic impedance. 10.3 Sampling test: samples shall be taken from the delivery batch, and the sampling quantity shall be based on the agreement between the two parties. If the user does not raise any objection, sampling shall be carried out according to the manufacturer's regulations. If the first sampling fails, another package shall be sampled and the unqualified items shall be tested for the second time. If they still fail, the test shall be considered unqualified. 10.4 Test methods 10.4.1 General test methods shall comply with the relevant test method standards and be specified in subsequent standards. 10.4.2 Special test methods shall be specified in relevant standards. 11 Packaging 11.1 Cables shall be delivered in drums or in drawings and neatly packed. Cable heads shall be sealed. Cable drums shall comply with the provisions of GB 4004 and GB 4005. The inner radius shall not be less than the allowable bending radius in the cable shrinkage chamber. 11.2 Each package shall be attached with a label and marked: Manufacturer's name or trademark:
b. Product model specification:
Length, mm
Wd,
e, manufacturing date, year, month:
Standard number or certification mark
2. Correct rotation direction of the switch,
11.3 When packing, the outer cover of the box should be marked with:, Manufacturer's name or trademark:
b. Product model specification:
: Certification mark:
d, body size and weight,
Moisture-proof and heat-proof mark.
GB 9334.1-88
W.8
Corona acid test
Recovery test
The test voltage V
The extinction voltage value is specified in the local standards. The attenuation constant
should be specified in the local standards.
Characteristic resistance
shall be specified in the subsequent standards,
heating test
shall be specified in Table 7,
sheath type
oxygen protection
duration m
test nature
prohibition time
spark spot plug
test voltage upper V
no acid
all click time 2
test results
decrease/
specified by the subsequent standards
W.8,10 heating specification test
GB 9334.1--88
shall be able to withstand the decay 8 Specified heating after rolling test. Table
Electric change protection pot
Glazed protection
Solid protection product
200±5
Outer diameter of sample protection product.
Good 11 High temperature after cold bending test
Test support diameter mm
Number of bending
Smin [0 times
min 10 times
Test results
The end of the screw and the sheath shall
No mechanical damage
Electric should be able to withstand the high temperature after the maximum exposure specified in Table 9. After the test, the end of the sample and the sheath shall have no mechanical damage during the test. The electric sugar is first exposed to the high temperature for a specified time, then cooled in a self-cooling case for 1 E, and then exposed to the low temperature for a specified time. Then roll the system on a test rod of specified diameter. Electrostatic protection
Holy gas jacket
Polytetraoxyethylene
Electrophilic
High overflow
250±5
Time h
Maximum resistance
8.12 Low temperature narrow bend test
The electrostatic duct shall be able to pass the specified low temperature bend test for 10 min. Time
Direct dyeing time
With current national effect
Rod outer diameter
12.7mm or 3 Figure
Specimen outer diameter
D212.7mm【Figure
Light test test release of inert gas and inorganic cutting injury. Table 10
Protection type
New B explosion transformer
With tetraethylene oxide electric worry
8.13 Flowability test
Test place
On
The electric fuel shall be able to withstand the flowability test specified in Table 11, Bin static outer diameter mm
Product number
D 12.7 mm or 3 ;
D≥12.7mm[
W. Test thickness
100±2
8.14 Identification mark
GB 9334.1-B8
Reading time
In the standard
Absolute position % Not more than
The identification mark of the electric jump shall comply with the provisions of GB 6995.3. The content of the mark shall be the manufacturer's name and trademark, certification mark and model. 8.15 Special performance
If required, it shall be specified in the subsequent standards. 9 Delivery length
The delivery length of solid polyethylene insulation shall not be less than 100m, and the short section shall not be less than 10m. The delivery length of solid polyurethane insulation shall not be less than 45m, and the short section shall not be less than 3m. The delivery quantity of short-length cables shall not exceed 13% of the total length of the delivery. According to the agreement between the two parties, cables of any length can be delivered. The error of length measurement shall not exceed ±0.5%.
10 Test and acceptance
10.1 Products shall be inspected and supervised by the technical inspection department of the manufacturer before delivery. Products shall be accompanied by a product inspection certificate. 10.2 Products shall be tested according to the following provisions. Type test items: all performance items specified in the standard. b. Sampling test items: conductor structure, insulation, sheath and insulation size, low temperature performance of ethylene oxide sheath, chemical test film of armored steel wire coating. Routine test items: insulation resistance, voltage test, corona test, capacitance constant, characteristic impedance. 10.3 Sampling test: samples shall be taken from the delivery batch, and the sampling quantity shall be based on the agreement between the two parties. If the user does not raise any objection, sampling shall be carried out according to the manufacturer's regulations. If the first sampling fails, another package shall be sampled and the unqualified items shall be tested for the second time. If they still fail, the test shall be considered unqualified. 10.4 Test methods 10.4.1 General test methods shall comply with the relevant test method standards and be specified in subsequent standards. 10.4.2 Special test methods shall be specified in relevant standards. 11 Packaging 11.1 Cables shall be delivered in drums or in drawings and neatly packed. Cable heads shall be sealed. Cable drums shall comply with the provisions of GB 4004 and GB 4005. The inner radius shall not be less than the allowable bending radius in the cable shrinkage chamber. 11.2 Each package shall be attached with a label and marked: Manufacturer's name or trademark:
b. Product model specification:
Length, mm
Wd,
e, manufacturing date, year, month:
Standard number or certification mark
2. Correct rotation direction of the switch,
11.3 When packing, the outer cover of the box should be marked with:, Manufacturer's name or trademark:
b. Product model specification:
: Certification mark:
d, body size and weight,
Moisture-proof and heat-proof mark.
GB 9334.1-88
W.8
Corona acid test
Recovery test
The test voltage V
The extinction voltage value is specified in the local standards. The attenuation constant
should be specified in the local standards.
Characteristic resistance
shall be specified in the subsequent standards,
heating test
shall be specified in Table 7,
sheath type
oxygen protection
duration m
test nature
prohibition time
spark spot plug
test voltage upper V
no acid
all click time 2
test results
decrease/
specified by the subsequent standards
W.8,10 heating specification test
GB 9334.1--88
shall be able to withstand the decay 8 Specified heating after rolling test. Table
Electric change protection pot
Glazed protection
Solid protection product
200±5
Outer diameter of sample protection product.
Good 11 High temperature after cold bending test
Test support diameter mm
Number of bending
Smin [0 times
min 10 times
Test results
The end of the screw and the sheath shall
No mechanical damage
Electric should be able to withstand the high temperature after the maximum exposure specified in Table 9. After the test, the end of the sample and the sheath shall have no mechanical damage during the test. The electric sugar is first exposed to the high temperature for a specified time, then cooled in a self-cooling case for 1 E, and then exposed to the low temperature for a specified time. Then roll the system on a test rod of specified diameter. Electrostatic protection
Holy gas jacket
Polytetraoxyethylene
Electrophilic
High overflow
250±5
Time h
Maximum resistance
8.12 Low temperature narrow bend test
The electrostatic duct shall be able to pass the specified low temperature bend test for 10 min. Time
Direct dyeing time
With current national effect
Rod outer diameter
12.7mm or 3 Figure
Specimen outer diameter
D212.7mm【Figure
Light test test release of inert gas and inorganic cutting injury. Table 10
Protection type
New B explosion transformer
With tetraethylene oxide electric worry
8.13 Flowability test
Test place
On
The electric fuel shall be able to withstand the flowability test specified in Table 11, Bin static outer diameter mm
Product number
D 12.7 mm or 3 ;
D≥12.7mm[
W. Test thickness
100±2
8.14 Identification mark
GB 9334.1-B8
Reading time
In the standard
Absolute position % Not more than
The identification mark of the electric jump shall comply with the provisions of GB 6995.3. The content of the mark shall be the manufacturer's name and trademark, certification mark and model. 8.15 Special performance
If required, it shall be specified in the subsequent standards. 9 Delivery length
The delivery length of solid polyethylene insulation shall not be less than 100m, and the short section shall not be less than 10m. The delivery length of solid polyurethane insulation shall not be less than 45m, and the short section shall not be less than 3m. The delivery quantity of short-length cables shall not exceed 13% of the total length of the delivery. According to the agreement between the two parties, cables of any length can be delivered. The error of length measurement shall not exceed ±0.5%.
10 Test and acceptance
10.1 Products shall be inspected and supervised by the technical inspection department of the manufacturer before delivery. Products shall be accompanied by a product inspection certificate. 10.2 Products shall be tested according to the following provisions. Type test items: all performance items specified in the standard. b. Sampling test items: conductor structure, insulation, sheath and insulation size, low temperature performance of ethylene oxide sheath, chemical test film of armored steel wire coating. Routine test items: insulation resistance, voltage test, corona test, capacitance constant, characteristic impedance. 10.3 Sampling test: samples shall be taken from the delivery batch, and the sampling quantity shall be based on the agreement between the two parties. If the user does not raise any objection, sampling shall be carried out according to the manufacturer's regulations. If the first sampling fails, another package shall be sampled and the unqualified items shall be tested for the second time. If they still fail, the test shall be considered unqualified. 10.4 Test methods 10.4.1 General test methods shall comply with the relevant test method standards and be specified in subsequent standards. 10.4.2 Special test methods shall be specified in relevant standards. 11 Packaging 11.1 Cables shall be delivered in drums or in drawings and neatly packed. Cable heads shall be sealed. Cable drums shall comply with the provisions of GB 4004 and GB 4005. The inner radius shall not be less than the allowable bending radius in the cable shrinkage chamber. 11.2 Each package shall be attached with a label and marked: Manufacturer's name or trademark:
b. Product model specification:
Length, mm
Wd,
e, manufacturing date, year, month:
Standard number or certification mark
2. Correct rotation direction of the switch,
11.3 When packing, the outer cover of the box should be marked with:, Manufacturer's name or trademark:
b. Product model specification:
: Certification mark:
d, body size and weight,
Moisture-proof and heat-proof mark.
GB 9334.1-88
W.Test temperature
100±2
8.14 Identification mark
GB 9334.1-B8
Reading time
In the following standard
Absolute position % Not more than
The identification mark of the cable shall comply with the provisions of GB 6995.3. The content of the mark shall be the manufacturer's name and trademark, certification mark and model. 8.15 Special performance
If required, it shall be specified in the subsequent standards. 9 Delivery length
The delivery length of solid polyethylene insulation cable shall not be less than 100m, and the short section shall not be less than 10m. The delivery length of solid polyurethane insulation cable shall not be less than 45m, and the short section shall not be less than 3m. The delivery quantity of short section cable shall not exceed 13% of the total delivery length. According to the agreement between the two parties, the cable can be delivered in any length. The error of length measurement shall not exceed ±0.5%.
10 Test and acceptance
10.1 Products shall be inspected and supervised by the technical inspection department of the manufacturer before being shipped out. The shipped products shall be accompanied by a product inspection certificate.10.2 Products shall be tested according to the following provisions. Type test items: all performance items specified in the standard. b. Sampling test items: conductor structure, insulation, sheath and insulation size, low temperature performance of ethylene oxide sheath, chemical test film of armored steel wire coating. Routine test items: insulation resistance, voltage test, corona test, capsule reduction constant, characteristic impedance. 10.3 Sampling test shall be sampled from the delivery batch, and the sampling quantity shall be based on the agreement between the two parties. If the user does not raise any objection, sampling shall be carried out according to the manufacturer's regulations. If the first sampling fails, another sampling of the packaging quantity shall be carried out for the second test of the unqualified items. If it still fails. This criticism is unqualified
10.4 Test method
10.4.1 General test method
Comply with the relevant test method standards and be specified in the subsequent standards. 10.4.2 Special test methods
Should be specified in the relevant standards.
11 Packaging
11.1 The cable should be delivered in drums or drawings and neatly packed. The cable ends should be sealed. The cable drum should comply with the provisions of GB 4004 and GB 4005. The inner radius should not be less than the allowable bending radius in the cable shrinkage room. 11.2 Each package should be attached with a label and marked:. Manufacturer name or trademark:
b. Product model specification:
Length, mi
Wd unit,
e Manufacturing date, year and month:
Standard number or certification mark
2. The correct rotation direction of the electric disk,
11.3 When packing, the outer cover of the box should be marked with:, manufacturer name or trademark:
b. Product model specification:
: certification mark:
d. Body size and weight,
moisture-proof and heat-proof mark.
GB 9334.1-88
W.Test temperature
100±2
8.14 Identification mark
GB 9334.1-B8
Reading time
In the following standard
Absolute position % Not more than
The identification mark of the cable shall comply with the provisions of GB 6995.3. The content of the mark shall be the manufacturer's name and trademark, certification mark and model. 8.15 Special performance
If required, it shall be specified in the subsequent standards. 9 Delivery length
The delivery length of solid polyethylene insulation cable shall not be less than 100m, and the short section shall not be less than 10m. The delivery length of solid polyurethane insulation cable shall not be less than 45m, and the short section shall not be less than 3m. The delivery quantity of short section cable shall not exceed 13% of the total delivery length. According to the agreement between the two parties, the cable can be delivered in any length. The error of length measurement shall not exceed ±0.5%.
10 Test and acceptance
10.1 Products shall be inspected and supervised by the technical inspection department of the manufacturer before being shipped out. The shipped products shall be accompanied by a product inspection certificate.10.2 Products shall be tested according to the following provisions. Type test items: all performance items specified in the standard. b. Sampling test items: conductor structure, insulation, sheath and insulation size, low temperature performance of ethylene oxide sheath, chemical test film of armored steel wire coating. Routine test items: insulation resistance, voltage test, corona test, capsule reduction constant, characteristic impedance. 10.3 Sampling test shall be sampled from the delivery batch, and the sampling quantity shall be based on the agreement between the two parties. If the user does not raise any objection, sampling shall be carried out according to the manufacturer's regulations. If the first sampling fails, another sampling of the packaging quantity shall be carried out for the second test of the unqualified items. If it still fails. This criticism is unqualified
10.4 Test method
10.4.1 General test method
Comply with the relevant test method standards and be specified in the subsequent standards. 10.4.2 Special test methods
Should be specified in the relevant standards.
11 Packaging
11.1 The cable should be delivered in drums or drawings and neatly packed. The cable ends should be sealed. The cable drum should comply with the provisions of GB 4004 and GB 4005. The inner radius should not be less than the allowable bending radius in the cable shrinkage room. 11.2 Each package should be attached with a label and marked:. Manufacturer name or trademark:
b. Product model specification:
Length, mi
Wd unit,
e Manufacturing date, year and month:
Standard number or certification mark
2. The correct rotation direction of the electric disk,
11.3 When packing, the outer cover of the box should be marked with:, manufacturer name or trademark:
b. Product model specification:
: certification mark:
d. Body size and weight,
moisture-proof and heat-proof mark.
GB 9334.1-88
W.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.