JB/T 9005.7-1999 JB/T 9005.7-1999 Casting pulley for crane, type D JB/T9005.7-1999 Standard download decompression password: www.bzxz.net

JB/T9005.7--1999
This standard is a revision of DIN15418:1982 Part 1 Part 3 "(Type D wire rope pulley). Only the original standard was edited during the revision. This standard is a modification of 7BJ80006.7.-87 "Cast pulley for crane", and the main technical content has not changed. This standard is part of the J1B3/T9005 "Cast pulley for crane" series of standards, which includes the following 10 parts: JB/T 9005. 1 -- 1999
JB/T 9005. 2--1999
JB/T 9005. 3
JB/T 9005. 4--1999
JB/T 9005.5
JB/T 9005. 6--1999
JB/T 9005.7--1999
JB/T 9005. 8---1999
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Selection series and matching
Type, hub and bearing size
Cast pulley for crane
Cast pulley for crane
JB/T 9005. 9 - 1999
Cast pulley for crane
JB/T 9005.J0--1999
Casting sheaves for cranes
This standard replaces ZBJ80006.7-87 from the date of implementation. E-type
Technical conditions
This standard is proposed and managed by the National Technical Committee for Standardization of Hoisting Machinery. The responsible drafting unit of this standard: Dalian Daqi Group Co., Ltd. The main drafters of this standard: Zhou Yu'an and Cui Zhenyuan. 434
1 Scope
Machinery Industry Standards of the People's Republic of China
Casting sheaves for cranes
Type D-Casting sheaves for cranesJB/T9005.7--1999
Replaces 2BJ80)006.7--87
This standard applies to cast wire rope pulleys (hereinafter referred to as pulleys) with rolling bearings and no inner sleeves that require strict sealing within the scope of the crane movable pulley block.
Pulleys in this standard can also be used in other pulleys in wire rope transmission, such as fixed pulleys or other load-bearing parts other than movable pulley blocks.
2 Referenced standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised. Parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T68--1985 Slotted countersunk screws
GB/T276-1994 Rolling bearings Deep groove ball bearings Dimensions GB/T283--1994 Rolling bearings Cylindrical roller bearings Dimensions GB/T819-1985 Cross recessed countersunk screws
3 Types and dimensions
3.1 Type I pulleys are divided into DI type (with deep groove ball bearings) and D, type (with cylindrical roller bearings) according to the different types of rolling bearings used. The type and size of D-type pulleys are detailed in Figure 1 and Table 1. E = B:-5 Www.bzxZ.net
Approved by the State Bureau of Machinery Industry on June 28, 1999
D2 type
D type
Implemented on January 1, 2000
JB/T9005.7-1999
Marking example:
Wire rope diameter d = 25mm, pulley diameter D = 630mm and diameter LD)-90mm type I pulley, marked as: D, 25X630-90JB/T 9005.7
Rolling bearing code
1), type
According to GB/T276
According to GB/T283
Note: To facilitate the installation of the pulley, the axial clearance on each side should be specified to be at least 1mm in the connection structure. 3.2 | | tt | M10×25
M12×30
M12x 30
M12X30
M12×30
M12×30
M12x30
M12×30
M12×30
M16×40
For the dimensions of spacers (AT or BT) and spacer rings (H) for D-type pulleys, please refer to Figures 2 to 4 and Table 2. Marking example:
D-type pulley with diameter 1), = -90mm, with spacer (AT), marked as: spacer A90JB/T 9005.7--1999
D-type pulley with diameter D, = 90mm, with spacer (BT). Marked as: spacer BT 90JB/T 9005. 7.--1999 D-type pulley with diameter D, -160mm, with spacer (H), marked as: spacer H160JB/T 9005.7-1999
Number of screws
(When installing a pulley on the pulley shaft)Figure 2 Spacer (AT)
Sleeve (AT)
JB/T9005.7--1999
(Bs=2Bs-5)
(When installing multiple pulleys in parallel on the pulley shaft)Figure 3 Spacer (BT)
Unit weight||tt| |Sleeve (BT)
Single piece weight
Figure 4 Spacer ring (H)
Ring (H)
Single piece weight
Spacer sleeve (AT)
Single piece weight
JB/T9005.7
Table 2 (end)
Spacer sleeve (BT)
1) When multiple pulleys are arranged in parallel on a shaft, the length of the spacer sleeve (BT) is B=2B5.
3.3 For the dimensions of the cover (G) for D-type pulley, please refer to the specified marking examples in Figure 5 and Table 3:
Piece weight
The grooved sealing cover (G) for D-type pulley with diameter D, = 160mm is marked as: Cover G160JB/T9005.7--1999
Figure 5 Groove-type sealing cover (G)
Spacer ring (H)
Piece weight
Piece weight
JB/T9005.7-1999
Table 3 (End)
Piece weight
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.