This standard specifies the general requirements for the compilation method of series models of special equipment for wires and cables. This standard applies to the compilation of series models of special equipment for wires and cables, including main machines, units, production lines, auxiliary devices, test equipment, trays and molds. JB/T 5824.1-1991 Classification and code of special equipment for wires and cables JB/T5824.1-1991 Standard download decompression password: www.bzxz.net

1 Subject content and scope of application
Machinery Industry Standard of the People's Republic of China
Equipment for special wires and cables
Product classification and code
Part 1 General provisions
1.1 This standard specifies the general requirements for the compilation method of series models of special wire and cable equipment. JB/T5824.1-—91
Replaces JB2863-81
1.2 This standard applies to the compilation of series models of special wire and cable equipment, including mainframes, units, production lines, auxiliary devices, test equipment, trays and molds.
2 Reference standards
GB2900
JB3750
GB3935
JB/Z263
3 Terminology
Guidelines for standardization work Product standard compilation regulations Electrical terminology
Product classification regulations
Basic standardization terms
Electrical product hierarchical terminology series
3.1 The terms of this standard adopt the interpretations of GB2900, GB3935, JB3750 and JB/Z263. 3.2 Host
Refers to the special equipment for wires and cables used to complete the main process of wire and cable manufacturing and processing - an independent unit that realizes the main process in a unit or production line.
3.3 Auxiliary device
A unit that is matched with the host to form a special unit or production line for manufacturing wires and cables, and assists the host to realize the functions of the host. 3.4 Unit
Specialized equipment for manufacturing wires and cables, consisting of the same type of main machine and other auxiliary devices. 3.5 Production line
Specialized equipment for manufacturing wires and cables, consisting of different types of main machines and other auxiliary devices. 3.6 Detection device (online detection device)
Specialized instrument or device installed on the unit or production line to directly conduct continuous or monitoring inspection and testing of its components during the production process of wires and cables, or it can also realize feedback adjustment while continuous testing, the latter can also be called a measurement and control device. 3.7 Main parameter
Invariant parameter that characterizes the structural characteristics or functional characteristics of the special equipment for wires and cables. As the specification symbol of the equipment, the main parameter generally only selects one invariant parameter, and it can be selected when it cannot be satisfied. 3.8 Design serial number
Represents the different design sequences of products of the same model and specification. The specified symbol is suffixed at the end of its model: to indicate different design sequences, when a product with a certain design serial number is improved or modified, the specified symbol is suffixed to the design serial number. 3.9 Derived code
For products of the same model and specification, when the basic type remains unchanged but the basic functions of the products are different, the symbols specified in the Ministry of Machinery and Electronics Industry approved on October 17, 1991 and implemented on October 1, 1992 shall be added to the end of the product model.
3.10 Combination code
JB/T5824.1--s1
For units or production lines of the same model and specification, when the main parameters remain unchanged but only the specifications or the number and position of the combination of the auxiliary devices are changed, the specified symbols shall be added to the end of the second part of the specification, i.e. the product mark, to indicate different combinations. 4 Product level series
4.1 The determination of product levels shall comply with the provisions of JB/Z263. According to the characteristics of special equipment for wires and cables, its product levels are as specified in Table 1. 4.2
Basic parts
Low level
High level
Product categories
The classification of product categories shall comply with the provisions of JB3750. Parts
Components or devices
Product line
Complete equipment
Product level series name
Special equipment for electric wires and cables is divided into four levels: category, series, type and specification. Special ones are allowed to be divided into three levels: category, type and specification. Category: divided according to the processing technology characteristics of cable products and the main functional characteristics of equipment products. a.
Series: divided according to the working principle or structural characteristics or processing object characteristics of the product in the same category. b.
Type: divided according to the structural type of the product in the same series of products. Based on the basic product, there can be derived products. c.
Specification: divided according to its main parameters in the same series or the same type of products. 6 Product model
6.1 The product model consists of concise symbols indicating the technical characteristics of the product category, series and type. a. Series model: consists of symbols indicating the product category and series. b. Product model: consists of symbols indicating the product category, series and type. 6.2 The model characters are uppercase Latin letters and should generally not exceed 4 characters. The letters "I" and "0" shall not be used, and footnotes or corner notes shall not be added.
The symbols of derived types are uppercase Latin letters, added in alphabetical order. 6.3 The meaning of the model characters shall comply with the provisions of Table 2. For the classification of categories, series and types, please refer to Chapters 3 to 6 of this standard. 7 Design serial number
7.1 The design serial number is composed of a line "two" and Arabic numerals at the end of the product model. 7.2 The code for equipment improvement or modification consists of the symbol "/" and Arabic numerals. 102
Product Specifications
JB/T5824.1—91
Main parameters indicating product specifications are in Arabic numerals. Roman numerals or other numerals are not allowed. The semi-grid line “” and “\
9Combination Code
“+” are allowed in the specification code. In principle, “×” is not allowed. The combination code consists of uppercase Latin letters in brackets. Table 2
(annealing)
package, half, eight, change, (bow), and
form, fork, difference, measurement, length, punch
single, equal, pair, tape, plated, electric, conductor, ground two, (double), (two), (component) reverse, non, complex, waste, release, seam, attachment
sensor, tube, tank, steel, rod, strand, solid, light, high, scrape, welding horizontal, slide, live, bake, fire, red, return
dip, gold, twist, check, static, connection, reduction, diameter, exciting, cross, machine, dielectric armor, gram, hole, (cone), frame
aluminum, wheel, pull, vertical, cage, connection, screw, asphalt, cable, bare, cold mold, grinding
(machine)
flat, disk , (weaving), main
throw, row, bias, fatigue, break
tilt, lead, paint, cut, its, start, circle, pull, lack, take heat, winding, capacity, screw, flexible
vertical, three, bundle, water, silk, yarn, collection, test, nature, (extrusion) copper, tower, tube, same, through, support, elastic
(casting), (melting)
(plastic)
no, horizontal, tungsten, temperature, bending
type, star, box, small, hanging, rubber, tin, repair, line, direction, sex lead, pressure, swimming, transport, shake
rolling, straight, comprehensive, clock, paper, drill, needle, mesh, vertical, straight, tension, vibration, resistance, (cylinder) Note: All non-pronounced Chinese characters in the model are represented by brackets. 10
Model composition and examples
10.1 Mainframe
10.1.1 Mainframe model composition is shown in Figure 1.
10.1.2 Example
JB/T5824.1-91
Specification code
Improvement or modification code
Design serial number
Derived code (sometimes)
-Type code
Series code
Category code
a, sliding wire drawing machine, tower wheel type, sizing wheel diameter 120mm, number of stretching channels 21, number of incoming wire ends 1 or 4, first design, expressed as:
1 end LHT—1
4 ends LHT—1
120／21 (1 in the incoming wire end is omitted)
120/21/4
If there is improvement or modification after the first design, it is expressed as: LHT-1/1120/21||tt| |LHT-1/1120/21/4
Plastic extruder, low temperature screw type, screw diameter 65mm, aspect ratio 25, first design, expressed as: b.
Single head SPV65/25
Co-extrusion with 30/25 extruder
Separate extrusion with 90/25 extruder
SPV165/25-30/2 5
SPV-165/25+90/25
When there is improvement or modification after the first design, it is expressed as: SPV-1/165/25
SPV--1/165/25-30/25
SPV--1/165/25+90/25
10.2 Unit
The unit model composition is shown in Figure 2.
Combination code
Figure 1 Host model
10.2.2 Example
a, the main machine is LHT-1120/21, with wire collection, pay-off and storage devices, which are represented as: LHT-1120/21 with continuous annealing device (A) LHT-1120/21 without continuous annealing device (B) The combination of other auxiliary devices can be changed according to (C), (D) and so on. 104
JB/T5824.1-91
b, the main machine is SPV-165/25, with wire collection, pay-off devices, water tank and traction device, which are represented as: SPV-165/25 with spark test device (A) SPV-165/25 without spark test device (B) The combination of other auxiliary devices can be changed according to (C), (D) and so on. c The main machine is SPV-165/25+120/20-90/20, with steam cross-linking device and other necessary auxiliary devices, which are represented by L-type traction device SPV-165/25+120/20-90/20 (A) and D-type traction device SPV-16525+120/20-90/20 (B). The combination of other auxiliary devices is as follows (C), (D) and so on. 10.3 Production line
10.3.1 The composition of production line models is shown in Figure 3.
Combination code
Specification of the second host
Specification of the first host
Design serial number
-Category code of the second host
10.3.2 Example
Category code of the first host
The first host is LHT250/17 and the second host is SPV65/25, which is expressed as: L+S250/17+65/25a.
b. The first host is SPV150/25 and the second host is KRB800/2, which is expressed as: S+K150/25+800/2c.
The design serial number, design improvement or modification, and the code and its position in different combinations are the same as those specified for the host. 11 Specification composition
The specification composition shall comply with the provisions of Appendix A (Supplement) of this standard. Example
Wire drawing machine---diameter of sizing wheel is 120mm, stretching is 21 times, 4 wires are fed in, which is expressed as: 120/21/4a.
b. Enameling machine---wire diameter serial number 4, 1 oven, 12 heads, 8 coating times, which is expressed as: 4/1-12/812 Product marking
Product marking shall comply with the provisions of GB1.3, as shown in Table 3. Table 3
First component
Product name
Indicated by product model
No more than 4 characters
Second component
Technical features
Indicated by product specifications
No more than 16 characters
Standard number
Third component
Indicated by standard code and number
No more than 8 characters
For main machine and unit, see Table A1.
Host type
Ingot (rod) YD type
Metal clad
cS, cP
CG, CZ
Component twisted
a. Single mold
b. Split mold
c. Co-molded
d. Split mold, co-molded
Pressed S type
Armored KJ series Y type
KR series
KZ series
MP series S, J type
MX series
MG series||tt| |JB/T5824.1—91
Appendix A
Specifications of special equipment for electric wires and cables
(Supplement)
Table A1 Main machine, unit
Main parameter items and specifications
Rod diameter mm
Production wheel diameter mm
Roller diameter mm/number
Sizing wheel diameter mm/Number of stretching paths/Number of incoming wire ends to be determined
Maximum wire diameter mm/number of ends
Take-up reel dimm
Pay-out reel dlmm/number||tt| |Pay-off reel dlmm/number and configuration/equal value take-up reel dlmm
Pay-off reel dlmm/number
Pay-off reel dlmm
Pay-off reel dlmm
Pay-off reel dlmm/number
Screw diameter mm/aspect ratio
Single-mode specification+single-mode specification
Single-mode specification-single-mode specification
Combined expression of b and c
Total pressure daN/number of plungers
Screw diameter mm
Pay-off reel dlmm/number and configuration||tt| |Take-up reel dlmm
Pay-off reel dlmm/number
Reel diameter mm×width
Width of tape (recommended)
Wire diameter serial number/number of furnaces-number of ends-number of paint passesWire diameter serial number/number of ends (recommended)
Belt width diameter mm/number
Number of spindles/spindle diameter×inner width mm
Power W
Power W
1 pass omitted
Main engine category
FL, FG series
FS, FP, FC
See Table A2 for auxiliary devices. bzxz.net
Reeling and unwinding
Device series
FX,SX,FD,SD
FG,SG,FJ,SJ
Annealing AD
AG,AS
Reel handling
Reel storage CP
Circulating lubrication
Die penetration
Drying device
Feeding device
Longitudinal wrapping device
Additional instructions:
F, L type
JB/T5824.191
Continued Table A1
Main parameter items and specifications
Reeling reel dlmm
Number of heads/spindle diameter×inner width
Table A2 Auxiliary devices
Main parameters and specifications
Capacity T|| tt||Wire drum diameter dlmmMaximum d1/minimum dl
Minimum dl/maximum dl/maximum load t
D1/number
Wire diameter/／Inner diameter × outer diameter of coil
Wheel diameter mm/number
Maximum traction daN
Traction wheel diameter mm/Pulley diameter mm/numberAnnealing wheel diameter mm/kVA
Power kVA
Belt drum diameter mm/number
Line speed m/min/Number of wheels
Counterweight kg
Guide wheel diameter mm/number/Guide wheel center distance mmPower kVA
Conveying device kg/h
Current A
Pressure daN
This standard is proposed and managed by Shanghai Cable Research Institute of the Ministry of Machinery and Electronics Industry. This standard is drafted by Shanghai Cable Research Institute and other units. The main drafters of this standard are Ou Xuecheng and Zhu Yuhui.
Design serial number, design improvement or modification, and the code and position of different combinations shall be the same as those specified for the main machine. 11 Specification composition
Specification composition shall comply with the provisions of Appendix A (Supplement) of this standard. Example
Wire drawing machine---diameter of sizing wheel 120mm, 21 stretching passes, 4-head wire feeding, expressed as: 120/21/4a.
b. Enameling machine---wire diameter serial number 4, 1 drying oven, 12 heads, 8 coating passes, expressed as: 4/1-12/812 Product marking
Product marking shall comply with the provisions of GB1.3, as shown in Table 3. Table 3
First component
Product name
Indicated by product model
No more than 4 characters
Second component
Technical features
Indicated by product specifications
No more than 16 characters
Standard number
Third component
Indicated by standard code and number
No more than 8 characters
For host and unit, see Table A1.
Host type
Ingot (rod) YD type
Metal clad
cS, cP
CG, CZ
Component twisted
a. Single mold
b. Split mold
c. Co-molded
d. Split mold, co-molded
Pressed S type
Armored KJ series Y type
KR series
KZ series
MP series S, J type
MX series
MG series||tt| |JB/T5824.1—91
Appendix A
Specifications of special equipment for electric wires and cables
(Supplement)
Table A1 Main machine, unit
Main parameter items and specifications
Rod diameter mm
Production wheel diameter mm
Roller diameter mm/number
Sizing wheel diameter mm/Number of stretching paths/Number of incoming wire ends to be determined
Maximum wire diameter mm/number of ends
Take-up reel dimm
Pay-out reel dlmm/number||tt| |Pay-off reel dlmm/number and configuration/equal value take-up reel dlmm
Pay-off reel dlmm/number
Pay-off reel dlmm
Pay-off reel dlmm
Pay-off reel dlmm/number
Screw diameter mm/aspect ratio
Single-mode specification+single-mode specification
Single-mode specification-single-mode specification
Combined expression of b and c
Total pressure daN/number of plungers
Screw diameter mm
Pay-off reel dlmm/number and configuration||tt| |Take-up reel dlmm
Pay-off reel dlmm/number
Reel diameter mm×width
Width of tape (recommended)
Wire diameter serial number/number of furnaces-number of ends-number of paint passesWire diameter serial number/number of ends (recommended)
Belt width diameter mm/number
Number of spindles/spindle diameter×inner width mm
Power W
Power W
1 pass omitted
Main engine category
FL, FG series
FS, FP, FC
See Table A2 for auxiliary devices.
Reeling and unwinding
Device series
FX,SX,FD,SD
FG,SG,FJ,SJ
Annealing AD
AG,AS
Reel handling
Reel storage CP
Circulating lubrication
Die penetration
Drying device
Feeding device
Longitudinal wrapping device
Additional instructions:
F, L type
JB/T5824.191
Continued Table A1
Main parameter items and specifications
Reeling reel dlmm
Number of heads/spindle diameter×inner width
Table A2 Auxiliary devices
Main parameters and specifications
Capacity T|| tt||Wire drum diameter dlmmMaximum d1/minimum dl
Minimum dl/maximum dl/maximum load t
D1/number
Wire diameter/／Inner diameter × outer diameter of coil
Wheel diameter mm/number
Maximum traction daN
Traction wheel diameter mm/Pulley diameter mm/numberAnnealing wheel diameter mm/kVA
Power kVA
Belt drum diameter mm/number
Line speed m/min/Number of wheels
Counterweight kg
Guide wheel diameter mm/number/Guide wheel center distance mmPower kVA
Conveying device kg/h
Current A
Pressure daN
This standard is proposed and managed by Shanghai Cable Research Institute of the Ministry of Machinery and Electronics Industry. This standard is drafted by Shanghai Cable Research Institute and other units. The main drafters of this standard are Ou Xuecheng and Zhu Yuhui.
Design serial number, design improvement or modification, and the code and position of different combinations shall be the same as those specified for the main machine. 11 Specification composition
Specification composition shall comply with the provisions of Appendix A (Supplement) of this standard. Example
Wire drawing machine---diameter of sizing wheel 120mm, 21 stretching passes, 4-head wire feeding, expressed as: 120/21/4a.
b. Enameling machine---wire diameter serial number 4, 1 drying oven, 12 heads, 8 coating passes, expressed as: 4/1-12/812 Product marking
Product marking shall comply with the provisions of GB1.3, as shown in Table 3. Table 3
First component
Product name
Indicated by product model
No more than 4 characters
Second component
Technical features
Indicated by product specifications
No more than 16 characters
Standard number
Third component
Indicated by standard code and number
No more than 8 characters
For host and unit, see Table A1.
Host type
Ingot (rod) YD type
Metal clad
cS, cP
CG, CZ
Component twisted
a. Single mold
b. Split mold
c. Co-molded
d. Split mold, co-molded
Pressed S type
Armored KJ series Y type
KR series
KZ series
MP series S, J type
MX series
MG series||tt| |JB/T5824.1—91
Appendix A
Specifications of special equipment for electric wires and cables
(Supplement)
Table A1 Main machine, unit
Main parameter items and specifications
Rod diameter mm
Production wheel diameter mm
Roller diameter mm/number
Sizing wheel diameter mm/Number of stretching paths/Number of incoming wire ends to be determined
Maximum wire diameter mm/number of ends
Take-up reel dimm
Pay-out reel dlmm/number||tt| |Pay-off reel dlmm/number and configuration/equally divided take-up reel dlmm
Pay-off reel dlmm/number
Pay-off reel dlmm
Pay-off reel dlmm
Pay-off reel dlmm/number
Screw diameter mm/aspect ratio
Single-mode specification+single-mode specification
Single-mode specification-single-mode specification
Combined expression of b and c
Total pressure daN/number of plungers
Screw diameter mm
Pay-off reel dlmm/number and configuration||tt| |Take-up reel dlmm
Pay-off reel dlmm/number
Reel diameter mm×width
Width of tape (recommended)
Wire diameter serial number/number of furnaces-number of ends-number of paint passesWire diameter serial number/number of ends (recommended)
Belt width diameter mm/number
Number of spindles/spindle diameter×inner width mm
Power W
Power W
1 pass omitted
Main engine category
FL, FG series
FS, FP, FC
See Table A2 for auxiliary devices.
Reeling and unwinding
Device series
FX,SX,FD,SD
FG,SG,FJ,SJ
Annealing AD
AG,AS
Reel handling
Reel storage CP
Circulating lubrication
Die penetration
Drying device
Feeding device
Longitudinal wrapping device
Additional instructions:
F, L type
JB/T5824.191
Continued Table A1
Main parameter items and specifications
Reeling reel dlmm
Number of heads/spindle diameter×inner width
Table A2 Auxiliary devices
Main parameters and specifications
Capacity T|| tt||Wire drum diameter dlmmMaximum d1/minimum dl
Minimum dl/maximum dl/maximum load t
D1/number
Wire diameter/／Inner diameter × outer diameter of coil
Wheel diameter mm/number
Maximum traction daN
Traction wheel diameter mm/Pulley diameter mm/numberAnnealing wheel diameter mm/kVA
Power kVA
Belt drum diameter mm/number
Line speed m/min/Number of wheels
Counterweight kg
Guide wheel diameter mm/number/Guide wheel center distance mmPower kVA
Conveying device kg/h
Current A
Pressure daN
This standard is proposed and managed by Shanghai Cable Research Institute of the Ministry of Machinery and Electronics Industry. This standard is drafted by Shanghai Cable Research Institute and other units. The main drafters of this standard are Ou Xuecheng and Zhu Yuhui.SJ
Annealing AD
AG, AS
Reel handling
Wire storage CP
Circulating lubrication
Die-piercing device
Drying device
Feeding device
Longitudinal wrapping device
Additional instructions:
F, L type
JB/T5824.191
Continued Table A1
Main parameter items and specifications
Wire take-up reel dlmm
Number of heads/spindle diameter×inner width
Table A2 Auxiliary device
Main parameters and specifications
Capacity T
Wire reel diameter dlmmMaximum d1/minimum dl||tt| |Minimum dl/Maximum dl/Maximum load t
D1/Number
Wire diameter/／Inner diameter × outer diameter of coil
Wheel diameter mm/Number
Maximum traction daN
Traction wheel diameter mm/Pulley diameter mm/NumberAnnealing wheel diameter mm/kVA
Power kVA
Reel diameter mm/Number
Line speed m/min/Number of wheels
Counterweight kg
Guide wheel diameter mm/Number/Guide wheel center distance mmPower kVA
Conveying device kg/h
Current A
Pressure daN
This standard was proposed and managed by Shanghai Cable Research Institute of the Ministry of Machinery and Electronics Industry. This standard was drafted by Shanghai Cable Research Institute and other units. The main drafters of this standard are Ou Xuecheng and Zhu Yuhui. Reserve
1 omittedSJ
Annealing AD
AG, AS
Reel handling
Wire storage CP
Circulating lubrication
Die-piercing device
Drying device
Feeding device
Longitudinal wrapping device
Additional instructions:
F, L type
JB/T5824.191
Continued Table A1
Main parameter items and specifications
Wire take-up reel dlmm
Number of heads/spindle diameter×inner width
Table A2 Auxiliary device
Main parameters and specifications
Capacity T
Wire reel diameter dlmmMaximum d1/minimum dl||tt| |Minimum dl/Maximum dl/Maximum load t
D1/Number
Wire diameter/／Inner diameter × outer diameter of coil
Wheel diameter mm/Number
Maximum traction daN
Traction wheel diameter mm/Pulley diameter mm/NumberAnnealing wheel diameter mm/kVA
Power kVA
Reel diameter mm/Number
Line speed m/min/Number of wheels
Counterweight kg
Guide wheel diameter mm/Number/Guide wheel center distance mmPower kVA
Conveying device kg/h
Current A
Pressure daN
This standard was proposed and managed by Shanghai Cable Research Institute of the Ministry of Machinery and Electronics Industry. This standard was drafted by Shanghai Cable Research Institute and other units. The main drafters of this standard are Ou Xuecheng and Zhu Yuhui. Reserve
1 omitted
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.