JB/T 9955.2-1999 Radial forging machine accuracy
Basic Information
Standard ID:
JB/T 9955.2-1999
Standard Name: Radial forging machine accuracy
Chinese Name:
径向锻机 精度
Standard category:Machinery Industry Standard (JB)
state:in force
Date of Release1999-05-14
Date of Implementation:2000-01-01
standard classification number
Standard ICS number:Machinery Manufacturing>>Chipless Processing Equipment>>25.120.10 Forging Equipment, Punching Machines, Shearing Machines
Standard Classification Number:Machinery>>General Processing Machinery and Equipment>>J62 Forging Machinery
Publication information
other information
Focal point unit:National Forging Machinery Standardization Technical Committee
Publishing department:National Forging Machinery Standardization Technical Committee
Introduction to standards:
JB/T 9955.2-1999 This standard is a revision of ZB J62 004-87 "Radial forging machine accuracy". This standard is part of the JB/T 9955 "Radial forging machine" series of standards. This series of standards includes the following three parts: JB/T 9955.1-1999 Radial forging machine types and basic parameters JB/T 9955.2-1999 Radial forging machine accuracy JB/T 9955.3-1999 Radial forging machine technical conditions This standard specifies the geometric accuracy, working accuracy and inspection methods of radial forging machines. This standard is applicable to radial forging machines for hot forging of ferrous or non-ferrous metals with round and square sections. This standard was first issued in April 1987. JB/T 9955.2-1999 Radial forging machine accuracy JB/T9955.2-1999 Standard download decompression password: www.bzxz.net
Some standard content:
CS25.120.10
Machinery Industry Standard of the People's Republic of China
JB/T9955.2-1999
Radial Forging Machine
Published on 1999-05-14
Implemented on 2000-01-01
National Bureau of Machinery Industry
JB/T9955.2-1999Www.bzxZ.net
This standard is a revision of ZBJ62004-87 "Precision of Radial Forging Machines". The technical content of this standard is basically consistent with that of ZBJ62004-87, and it has only been re-edited according to relevant regulations. This standard shall be implemented from January 1, 2000. This standard shall replace ZBJ62004-87 from the date of implementation. This standard is proposed and issued by the National Technical Committee for Standardization of Forging Machinery. The responsible unit for the issuance of this standard is Liaoyang Forging Machine Tool Factory. This standard was first issued in April 1987.
Machinery Industry Standard of the People's Republic of China
Radial Forging Machine
This standard specifies the geometric accuracy, working accuracy and inspection method of radial forging machines. This standard is applicable to radial forging machines for forging sections and shear surfaces of ferrous or non-ferrous metal materials. 2 General requirements
2.1 The requirements for radial forging machine accuracy inspection shall comply with the relevant provisions for forging machine accuracy inspection. 2.2 The installation level of radial forging machine in longitudinal and general directions shall not be greater than 0.10-1000JB/T9955,2-1999
Replace 28362004-87
2.3 The tolerance value of the test item shall be calculated according to the actual test length. When the calculated result is less than 0.005m or equal to 0.005mm, it shall be ignored. When it is greater than 0.005mm, it shall be calculated as 0.01mm.
2.4 The inspection sequence of this standard does not represent the actual inspection sequence. For the convenience of inspection and testing, the inspection can be carried out in any order.
Guohao Machinery Industry Bureau 1999-05-14 approved 2000-01-01 actual screening
JB/T 9955.2 1999
JB/T 9955.21999
District Institute
JB/T9955.2-1999
00E-091
091-08
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.