This standard is applicable to the cupping test of metal plates and strips with a thickness of 0.2~2mm and a width of equal to or greater than 90mm. It is used to test the plastic deformation performance of metal plates and strips. GB/T 4156-1984 Metal cupping test method (thickness 0.2-2mm) GB/T4156-1984 standard download decompression password: www.bzxz.net

Beijing Standard of the People's Republic of China
Metal cupping test method
(thickness 0,2 ~ 2mm)
Metal cupping test method (dhleknrey 0.2.--2mm:
UDC660:620.162.2
GE415684
This is suitable for the cup test of the metal plate with a size of 100m. The plastic deformation of the metal strip is marked. The test system uses the head of the device to obtain the shape of the head. The test sample needs to be pressed into the die. The test boundary should be tested with a uniform penetration and a deep deformation. The symbol and name of the test machine are as shown in the figure and table below. The test machine should be used on a test machine with a mold, ground effect and punch. The size and tolerance are shown in the blood. The Beijing Standardization Bureau 84·024 issued
01:01| |tt||GB4166—84
with production space
detailed variation or user
note connection diameter
model
extreme outer diameter
heart country self-study
positive measurement area month and a half
.+Lai F times 3
small Shuangmin
: long ball system Lang points
long flow source Long
Zizhou should be able to accurately determine the crack avoidance north light penetration medical specimen standard pursuit: (send light, the self $.1
testing machine should have the standard of provincial series war cup actual depth, is the British small degree., ten digits above preparation can realize the teaching of purple, 3.2
method will, general mold and punch to have enough sleep difference, its work standard hardness to be too / flat HVT50 , in the test process! 3.3
can be shaped.
the test process head shall not be too large, the punch ball method must be able to work. 8.2.1
2 the punch is a joint type, the light activity is not low and the whole length is not false 9.8 also learn the center punch system, under the medium pressure stroke range, 5 core with the sample contact table and must be oxygen five lines, the axis of the rising punch must be straight. The speed of the two lines is 100 mm:
3. The testing machine should have a cumulative capacity of about 100kg (10kN) 3.7 The punch should be in contact with the surface of the sample. 4 sample
4.1 the width or diameter of the sample is 90~95mm.
.2 when cutting the sample, the sample must be kept straight, and its edges must be straight. Do not hand over the cutting and other uses. 4. The test fence does not need to be hammered or cold, hot. 1
4.4 The test specimens cut from the plate shall be tested without correction: 5
The test process
The test shall be carried out at a temperature of 10~35. If there are higher requirements for the test temperature, the test temperature shall be 235. Or the M plate of the sample bank shall be rotated 0.1mm.
5.8 In the test part: The test side shall bear the light effect in the stealing state along the fat, the lubrication of the general fat is recorded in the north, and the light effect is required. If other types of lubrication are used, the height of the two pressure wolves shall not be less than 9mm, and the height of the center plate shall not be less than 45mm,
5.5 The test machine shall be adjusted to the point of the tiger, and the result shall be in! Replace and tighten the mold, its test force is about 1000kgf (10) kN! , 6.6 In the case of large impact, the cupping test is carried out, and the test is carried out for 6~20mm, m days. The test station requires the limit, and the seam is reduced to the lower limit according to GB15684 to correct the instantaneous cracking. 5.7 When the double-opening is good, the test sample thickness (send light), the test is reduced. %. The measured cupping value is accurate to the bowl, and the ring is required. The test report should include the following:
This standard number!
. Test,
The thickness of the sample,
The type of the opening agent;
The cupping value/E.
GB4156-84
Appendix A
Formula for mixing graphite grease
《Parts》
Graphite grease should not contain corrosive substances, wax and fillers. The graphite lubricating grease compounding ratio is as follows: Type
Period (25 >, mm/10
Additional remarks:
Sauce is made of acid (kinetic acid),
Meat % CCAOH) 22,%
Seven is the content, % www.bzxz.net
Homogeneity, mm
Maximum particle size,
%, %
Viscosity (9T.B), e81
For internal point,
, The technical standard is proposed by the Ministry of Metallurgy of the People's Republic of China. This standard was drafted by Shanxianshan Iron and Steel Company. Drink
250-280
29 --28
100~120
When this standard is implemented, the original standard YB38-64 of the Ministry of Metallurgy "Test Method for Ring Suspension of Enterprises" is used as the standard.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.