Some standard content:
Classification number Y56
Case number 6918-2000
Light Industry Standard of the People's Republic of China
QB/T1475-2000
Spinning type fishing reel
2000-03-30 Issued
State Bureau of Light Industry
200008-01 Implementation
QB/T1475-2000
This standard is a revision of QB/T1475-2000, and has made corresponding modifications and supplements to the name, meaning, classification, requirements and test methods of the original standard. This standard is an appendix to the standard for fish reels.
This standard The standard is proposed by the National Light Industry Bureau Industry Management Department. The technical standard belongs to the National Product Standardization Center, and the responsible unit for this standard is: Ningji Beilun Precision Machinery Manufacturing Co., Ltd. This standard is issued by: Dongguan Kailiubing Co., Ltd., Chengluo Photosensitive Laser Tool Group Public School, Dazhu and Details Run Co., Ltd.
This standard is not required to be issued by: Zhan Haiyun, Jiatingyou, Fang Dagang, the main editor of this standard is the original Ministry of Light Industry issued the industry standard QB/1475·1992 urgent wheel issued. 1 Fan Yu
People's Republic of China Light Industry Industry Standard
Spinning Fishing Reel
QB/11475--2000
Generation QH/1 [175-1992
This standard specifies the definition, product category, requirements, test methods, test specifications, marking, packaging, transportation and storage of avoidance fish reels.
This standard applies to the overpressure fishing reels (referred to as overpressure reels) produced, modified or used when fishing. Technical standards are not applicable to the reels of this type. 2 Reference standards
The following are the provisions contained in this standard, which constitute the provisions of this standard. The cost of the large standard is valid when the version is displayed. The price standard department will CB191-1990 3771-1991 Determination of the qualitative performance of colorimetric and clean lacquers GE/T2828-1937 GB/T2823-1987 Procedure and detailed table for colorimetric counting and testing of oil samples (same as the procedure for colorimetric testing of the same standard as the procedure for ... 5296.1-[99]
Consumer product use summary
GB 5926-1986
Secondary industry Ma Jinhou Sanhe chemical request for the development of the dual-qualified product secretion test method light industry product service original Xie Wei's current strength test method GB 5533-1986
GB5938-1986 Light industry product exhibition design and management level planning business processing method 4 station recruitment test ANSS
G 594- 1986
CE6388-1936
GB 6543 1986
Complete work * genuine gold solution driver corrosion test result evaluation transport new package micro receiving and shipping mark
Flying list carton
G3T 6739—1996
GB7T7141-1992
GB 928G1988
3 Specifications
Determination of frequency of ship accidents
Plastic industry air system test method
Color and flow paint source test
This standard adopts the definition
3.1 Starcpower
When the wheel is locked in the force adjustment button and the reverse stop effect is achieved, when it is in a static state, the pulling force that each part of the wheel can enjoy under the load.
3.2 About utatipuwe
When the wheel is in normal operation, the control of each part on the output line is as follows. State Bureau of Light Industry 2000-C3~30 Standard
2050-09-01 Actual Shot
W.bzsoso.cOmB/11452000
3.3 No-load errptylaadtwistmanen
When the fishing force is uneven, the reel is driven to rotate from the static position to the reel for a stroke of 3m5. 3.4 Lifting systemharullesystemtea
The movable parts of the reel composed of the arm, arm, etc. 3.5 Main bodyhody
The housing for placing transmission components, upper guide parts, etc. 3.6 Main coverbadywover
The blue plate of the main body.
3. The main components of the reel are as follows:
3.8 The line density is the length of the line in the reel.
3.9 The reel is equipped with internal components such as anti-seizure mechanism and other internal components: 3. The line guide reel is equipped with internal components such as anti-seizure mechanism and anti-seizure mechanism.
311ti-reversatt:n
Lai Lai Chen Xing Tong double structure fee system
Note: Control has: rotating type, bumping type and pressing type, 3.12 Please apply (adjustment hand support) trag
Strong meter reversing line wheel (special wheel) rotating torque reduction part 315 wheel ree.0wwW.bzxz.Net
Main position meter will be lightly applied to the apple 1 Classification and naming
41 position wheel press test position can be divided into: front adjustment force purple, rear adjustment force station structure and control adjustment structure. 4. 1. 1 Front adjustment force will be
adjustment force set Ding shallow wheel still end of the fishing reel.
2.1.2 Power structure
The power device is the main and end of the color wheel, 4.1.3 The power adjustment structure
The power device is the main and end of the color wheel, 4.2 The general diagram of the fishing reel
3
1--wheel, 2-line, 3-center line: : whole, 5 Upper group, G5 wheel: 7-practice wheel: 8-borrow; 9-six: [5-stop certificate: 11-go to the south] Jing adjusts the force to practice the structure of the fish
1-wheel that is: 2-occupy wheel: 3-line light: 4-find war: 5-line grab: one-line wheel 7-hand, 2-adjusting force can clamp, 9-reverse stop key, 10-strong number, 11-1: Figure 2 rear adjustment female structure fish wheel
5 requirements
5.1 main majority
original farmer 1:
number of gears
B/T1475—2000
1-wheel: 2-force adjustment handle: 3-line drawing: 4-line hook: 5-line wheel 16-line guide wheel 7-wheel: 8-handle: 9-shaking: 10-pan stop group, 11-main body 3-handle summary fishing reel
number of axes
most straight
>35--50
>50~-60
>69~·1
>70~-80
30 ~-50
>50~-60
>6C~-70
>7G~-8C
Stock cloud empty
≤43x15-3
Static force
The wheel is subjected to large
uneven quantity
≤:70
Dynamic force
W gear||tt| |Bearing to
Human diameter
>30-~50
>50~69
>63--%
>5i~||tt ||oG~7℃
)~7H)
lj-sul
2-5~60
>tt~70
>59- Heart0
>3G--5C
>50r50
>G0~70
>30--50
Continued Table 1||t t||Maximum loading
030×10-4
5010-3
=40×10-3
$.55×10*1|| tt||≤35×10>
Static force
Dynamic force
Rotor crown
Unbalance
250
≤:250
Rotor axial
Note: The gears with more than 3 gears are A, and the gears with 2 gears are B: Type A reels are divided into Type A and Type B according to their strength. When the maximum no-load torque
is not strong, the drive wheel starts to rotate at rest for 30 catties m, and the gear wheel reciprocates for more than one stroke. The required torque should meet the requirements.
5.1.2 Static fishing method
Pay attention to the static force specified in Table 1: a) No mechanical parts should be damaged, broken or permanently deformed; 5) The line reel or rotating wheel should not slip;
QB/T1475-2000
c) All parts on the rotating wheel should not collide with the reel; 5.1.3 Dynamic fishing force
When the fishing reel is under the dynamic fishing force specified in Table 1, the line is collected for 30m: a) No mechanical parts should be damaged, broken or permanently deformed; 3) The rotating wheel should not collide with the line reel, body when rotating; 4) The reel, main body, line pulling mechanism, etc. when rotating. 5.1.4 Maximum unbalance of the rotating wheel
When the rotating wheel rotates at a speed of 55/n--7(K)r/mit, the maximum unbalance should meet the requirements of Table 1. 5.1.5 The axial momentum of the runner
age wheel shall be derived from the requirements of Table 1. 5.2 The parameters of the caster of the fishing reel are shown in Figure 2 and Figure 4, bag 2
65--50
5.3 Modifications and changes in the system
5.3.1 Running performance
14~·16
:4--36
Under normal load, the dynamic feeling is smooth, the release is soft, and there is no abnormal noise in the cassette model. 5.32 The clearance between the handle and the steering concave film is less than 0.5m: the radial clearance should be less than 0.3mmc5.3.3 The clearance between the inner light and the main body and the main benefit is usually m
14--:6
The main gear (or toothed disc) and the main body and the front cover are less than 0.3mm, and the clearance in all directions should be greater than 0.2mm. WW.bzsoso.cOm5.3.4 Broadcasting seat post station
QB/T1475—2000
The left and right interchangeable balance can be bent 90”, and the extension rate of the parts shall not fall off.5.3.5 The handle has a certain strength
The handle shall not be in a straight line when in use.
5.3.6 The code cover
After tightening, it shall not be broken or affected by the rotation.5.3. The time pressure performance of the transmission system
The main shaft end of the negative flower is The specified stopper should be able to work normally under the specified torque. 5.3.8 Strength of the arm system
When the arm system is subjected to the specified torque, the parts will not be permanently deformed. 5.4 Backstop system
5.4.1 Backstop performance
The backstop should have a backstop effect when it is in the backstop position. 5.4.2 Backstop blade change
The backstop blade change force should be 3, and there should be a sense of pain when it is effective. Table 3
Backstop pin
5. 4. 3 Check distance
Light-acting type
c s--4
Control type
3 -~25
Throwing type
The clearance of the rotating spoon of the rotating and pressing check pliers should be greater than 0.51mm. When the automatic check button is switched to the right position, the distance between the front and rear check ends should be less than 0.5m with a force of 0.2N. 5. 5 Force system
5.5.1 Force adjustment range
The force should be adjustable within the full force range of the dynamic force table: the full range is ± N. 5.5.2 Force quality
The friction force should be within the specified range, and the deviation should be 1% to 10% of the specified value. The force control structure is not limited to this.
5.5.3 Force adjustment position
The force adjustment knob shall not be driven during retraction and release. The force adjustment knob of the front force adjustment station shall not encounter full friction, and the screwing length with the clamping shaft shall be greater than 4 end distances.
5.5.4 Force adjustment strength
The force adjustment knob shall be 22 times the torque of the force adjustment knob, and the force adjustment system shall have no mechanical damage Damage: After the force adjustment knob of the rear force adjustment structure is spun, it shall not break or fall off when continuously inspected with a 0Nm torque torch. 5.5.5 Impact resistance of force adjustment system
Make the fishing reel stop, adjust the friction force to the dynamic fishing force, and use a 2mg speed change line of 200m, the force adjustment system shall not be completely ineffective, 5.6 Line reel
5.6.1 Winding performance
When the winding tension is ~5V, the front and rear ends of the first layer of the line reel should be within ~2mu of the inner surface of the reel. When winding to 0%, the line is arranged more flat, and the diameter of the circular grid formed should be less than 3mm, and the front end shall not be larger than the winding,
5.6.2 Relative position between the reel and the rotating wheel
03/T 1475-2000
When the reel is lowered to the lowest position, the bottom of the reel shall not be in contact with the upper part of the reel when the reel is raised to the highest position. 5,6.3 The distance between the reel shafts (a) should be less than 0.7m for the front and b) less than 1.5um for the rear force structure. 5.6.4 The reel steering angle should be less than 10°: 5.6.5 The reel sound should make a rhythmic sound when the reel is rotating forward and reverse. 5.6.5 Initial power of the line wheel
The stroke power of the line wheel is IN
5.8.7 Setting of the line
Table 4 Negative velvet should be set at the hook line clamp
Velvet wheel diameter
Line point diameter
2-:--5U
0.07~0 35
5. 6. Daily line wheel and buckle connection
5.6.8.1 I should be able to connect with the auxiliary.
50~~60
0.25-- 5.55
5.6.8.2 The pulley after digging should be able to withstand the axial force of 60~~70N
0.35--0.55
56.5.3 When the core reaches the bottom, the internal control force of the shaft of N can be used to lead the line pulley. Note: The positive bottom is set as the structure
6.7 Pool line mechanism
57.1 The position of the tow
70--8g||tt| |The stop belt position of the ground wire mechanism, the center of rotation of the guide wheel is set straight, and the error is within the soil "; when the line throwing machine is completed, the distance between each point on the upper part of the line wheel and the weight of the throwing money plane drawing should be not less than 5mm: the ground wire diagram and the plane of the pool pattern are placed, 5.7.2 The rated line power
The ground cutting extreme power should be within 0.5N~2.
When the pressure is 1C°,
5. 7. 1 Complexity
Max. 1. -85” When using the internal hitting and shaking level, the floating load mechanism should be able to move the positive belt position, 5.7.4 Capacity torque
Fully open the throwing board and its tear parts to the normal position force range a) Turn the wire drawing mechanism: 0.15Nm~030Nm; h) Turn the rocker arm: 0.3Nm~2Nm
5.7.5 The relationship between the throwing wire and the position of each part
It shall not rub against other parts during the rotation process. 5.7.6 Wire wheel
a) Light filling, surface relative wax value: Ra will be about 0.d4mb, the auxiliary direction and the warp gap are less than 0.2mm, and the ends of the No. 5 coin wheel shall not be exposed. 5.7.7 The combination of the line mechanism
The components of the casting mechanism should be firmly connected and the casting line should not be easily pulled out with a 10N pull. 5.7.8 The elastic line
The casting line should not be loose. 5.7.9 The life of the ground line mechanism
The use of the casting mechanism should be more than 5000 times. 5.8 The single-axis longitudinal distance between the reel and the body should be less than 2 meters when the reel is unloaded. 5.9 Main body
5.9.1 The main body and the main body plane distance: A-type reel should not be greater than 0.2m, B-type reel should not be greater than 0.2m, and the main body and main body misalignment should be less than 0.5mm.
5.9.2 Body vibration key
When the reel is reversed, use a 1SCr/mu~200:i rotating speed to start the rotation, and the main vibration shall not be greater than c.20mm. 5.10 Tightness
All parts on the reel shall not be loose, and the F control speed shall not drop less than the minimum specified by A. 5.11
Free reel epidemic test
The reel is continuously reversed for a total of 50C0m or each time, and the cylinder parts are not damaged. 5.12 Impact test
The fishing reel is installed on a reel seat with a height of about 1 meter, the reel seat is about 1 meter from the fishing bottom, and it is placed upright on a light semi-rigid surface of mercury. It can be turned upside down and all parts are not damaged.
5.13 Plastic parts
5.13.1 Appearance of plastic parts
The outer surface must be glossy and of normal color, without burrs, uneven lines, shapes, pits, marks or defects. 5.13.2 Aging resistance performance
Mainly scratches, yellowing, money, and ageing resistance performance of fishing reels: hang the test piece in an aging test box, the test temperature of the whole fishing reel is 120±1)℃: the test piece of the fishing reel is at (+1)℃, and kept warm for 48h. No powdering, cracking, spots, parts, color change, plasticity and other changes will occur. The deformation shall not affect the normal use.
h) After this test, the assembly shall meet the requirements of the design. 5.14 The surface of the coating should be smooth, hairless, without obvious defects and other mechanical damage. 5.15 Coating 5.15.1 Appearance The coating should be flat and clean, without any marks of brittleness, chipping, weak bottom, brittleness, bubbles, brittleness, scorching, pinholes, dirt, wrinkles, etc. All kinds of standard industry materials are free to download 5.15.2 Corrosion resistance of coating agent The corrosion resistance of coating should be 2 levels, 5.15.3 The hardness of coating should not be less than 211. 5.15.4 The coating adhesion of the coating should not be less than 2 levels.
5.15.5 Film drop solvent
Q9/T14/5—2000
The film surface has the specified drop resistance. 5.16 Coating
5. 1E. 1 Coating requirements
The metal coating and the substrate should be combined for half a circle, and the outer surface should not have peeling, shedding, discoloration, pinholes, etc. 5.16.2 Plating corrosion resistance
Metal coating corrosion resistance: Grade.
5.11. 1 Printed product appearance
That is, the product should be elastic, standard, and the pattern should be indicated.
5.17.2 Printed surface drop resistance notes
Special changes should be within the specified range. 5.17.3 Brushing surface temperature
5.17.4 Steel family record phenomenon
0. The surface and basic properties should be combined.
5.18 Free outside
The finished product and the wheel surface should be clean.
6 Test method
6.1 Main efficiency test
6.1.1 Maximum no-load visual energy test
At (23±2)℃, the relative power is not more than 70%, the fish grab is equipped with a circular arm with a total of five or more belts. One end of the line is fixed on the outer circle of the net and slides around the figure, and the other end of the line is applied. The line end force is calculated using formula (1).
Wu: F-the size of the force applied, N: M-the maximum torque value of the wheel, N·mH half, m
The return plate should be able to return to the ground without moving the differential wheel at a speed of 0~3m, and the cable wheel should be able to return to the ground without moving the differential wheel for more than one stroke. 6.1.2 The main parts are: (fixed negative wheel clamp, force controller with force adjustment range of 0~200N, adjustment accuracy of 1N), force sensor range of 200V), wire gauge (04Tm-5000), digital display force measuring method with 0~200NW
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.