Some standard content:
Pharmaceutical Machinery Industry Standard of the People's Republic of China JB20039.20040-2004
JB/T20041~20043-2004
Hammer Crusher
Knife Granulatorbzxz.net
Reciprocating Medicine Cutter
Medicine Washer
Rotary Medicine Cutter
Published on 2004-02-05
Implemented on 2004-06-01
Published by National Development and Reform Commission
ICS 11.120.30
Pharmaceutical Machinery Industry Standard of the People's Republic of China J/T20043-2004
Generation Y40-1993
Rotary Medicine Cutter
Ralary Herbal Medicine Slicing machinu2004-02-05 Issued
2004-06-01 Implementation
National Development and Reform Commission Issued
Normative documents
Terms and definitions
Classification and model
Test methods
Stealing regulations
Marking, packaging, transportation and purchase
JB/T 20048—2004
JB/T20043—2004
This standard is formulated according to the requirements of the pharmaceutical production quality management specification and GB/T1.1—20(K) and GB/T1.2—2002 standardization work rules, and is for YY0140·1993 "Rotary medicine cutting machine". This standard replaces YY/0140-1993 standard and YY/T(140-1993) from the date of implementation. Compared with 993, the ten technical changes are as follows: a) In addition to the card chapters and clauses, the following are:
Reference standards (BT378, GT10111.TB8, ZB30003.1; 5.1, 5.2.3. Month, 5.11.1.5,.2 clauses. h) The main single and clauses of the reference are as follows:
Sound increase test method: from tBT3768 rectangular method to GBT1/69 output * method: -4.1 in The method of compiling product model numbers is changed to YY/T (216) - Electrical safety requirements and test methods (certification 5226.1--2007. Two items are changed to item B.) The main chapters of the standard are as follows:
Contents of the label (see 8.1.1):
Its quality should be controlled by GB/TGX0.4 (see 6.3.4.2). This standard is proposed by the China Pharmaceutical Equipment Industry Association and is used by the pharmaceutical equipment industry. The Standardization Technical Committee is responsible for this standard. The drafting unit of this standard is Henan Zhouchuan Pharmaceutical Machinery Factory Co., Ltd. The main drafters of this standard are Zhao Liuzhu, Li Jiushan, Nai Shiyu. 40
1 Scope
Rotary medicine cutting machine
JB/T20043—2004
This standard specifies the terminology and definition, classification and model, requirements, test methods, inspection rules, instructions, packaging, transportation and operation of rotary medicine cutting machine.
This standard applies to rotary medicine cutting machine:
Normative references
The clauses in the following documents become the clauses of the technical standard through reference in this standard. For the referenced documents with dates, all subsequent amendments (excluding the content of outdated) or revisions are not applicable to this standard. However, the parties who have reached a consensus on the revision of this standard will study whether these more recent versions can be used. The document is not marked with a new version and is not applicable to this standard. GBT191 Color standard pictorial symbol
GB5226.1-2002 Safety of machinery - Electrical equipment of machinery - Part 1: General technical case GR/T6IK0.4 Surface roughness ratio wheel rail block polishing plus L female surface CR/T6388 Transport package and delivery mark
(BT9969.1-1998 Industrial product instruction manual General test GB13306 Sign
GB/T13384 General technical conditions for electromechanical product packages H Jinrun Method for measuring the sound pressure level of machine tool beam before closing YY/T216 Method for compiling the model of pharmaceutical machinery products 3 Terms and definitions
Effective use length of blade bladecusclcngthefficiently small opening, lifting or steel, etc., and directly used for cutting medicine. 4 Classification and model
4.1 The model of medicine cutting machine is YM021G.
4.2 Next number
The model mark is composed of product function code, type feature code and specification code. 41
JR/T 20043--2004
4.3 Marking example
Selection design guide: A, B, C for the first time
: Specification code: White medicine outlet width, mm
Type feature code: Rotary
One product model code, medicine dispenser
QZ1204 type: Table small after the first collection design, the medicine outlet width 12hmm rotary medicine dispenser. 5 Requirements
5.1 Material requirements
5.1.1 Direct contact approx. The missing parts should be made of materials that are corrosion-resistant and have little chemical reaction with or adsorption to the drug. 5.2 Working performance requirements
5.2.1 The transmission of the machine should be smooth and the noise should be small when loaded. 5.2.2 The feeding and retracting devices should be easy to operate and easy to control. 5.2.3 The temperature of the copper sleeve of the bearing in the operating part should be less than 14SC when loaded. 5.2.4 The cutting section should be accurate. The drug after processing should meet the requirements of 1 and the allowable error of the slice thickness in Table 1
2:0.8 - 1.5
>1.3 -3.0
>10 - 18
Total sound rate>
5.2.5 Lubricant for equipment (time-release) should be sealed and leak-free 5.3 Mechanism performance requirements
6.3.1 The cutter should rotate smoothly, and the distance between the blade and the lower edge of the blade should be less than 0.[5mm. The contact line between the cutter and the lower edge of the blade should be about 8% of the width
5.3.2 The blade clamping mechanism should be reliable, and there should be no possibility of loosening due to movement. 5.3. 3 Each mechanism should be easy to disassemble and clean: 5.3.4 Small blade quality requirements:
5.3.4.1 Blade HRC 52°HR5%°, small blade width complies with the width of the cut, the effective length of the blade should be greater than 50% to 80% of the total length 42
5.3.4.2, blade. Small surface smoothness Ra value is 3.2pmm5.3.4.3 Blade angle 20°23° Blade flatness 9. 5.4 Safety performance requirements
5.4.1 Electrical system safety requirements
5.4.1.1 The continuity of the protective grounding circuit should comply with GB5226.1-2002 19.2. 5.4.1.2 Insulation resistance shall comply with the provisions of 19.3 in GB5226.1-2002. 5.4.1.3 Voltage relief shall comply with the provisions of 19.4 in GR57.76.1-2IX12. 5.4.1.4 The protective grounding circuit shall comply with the provisions of 8.2 in GB5226.1-2002. 5.4.1.5 The button shall comply with the provisions of GB5226.]-2002[0,2. 5.4.1.6 The indicator light display shall comply with the provisions of 10.3 in GR.9226.1-2000. 5.4.1.7 The electrical wiring shall comply with the provisions of Chapter 14 in GB5226.1-2002, JB/T 200432004
5.4.1.R marking, warning signs and serial numbers shall comply with the provisions of Chapter 17 of GB5226.1-2002. 5.4.2 Protection requirements:
6.4.2.1 The material inlet and automatic feeding part shall be equipped with a full-scale warning plate, and the material inlet shall be equipped with an "emergency stop button". 5.4.2.2 All mechanical transmission parts shall be equipped with protective covers. B Test method
6.1 Materials
Check the quality certificate of the materials, and conduct inspections if there are any objections. 6.21 Perform performance tests
6.2.1 Operation test: Load operation. Splash inspection and GR/1 16769 regulations, 6.2.2 Material inlet and outlet test: Use Angelica sinensis. Chuan Luo Cheng Dai material test to confirm. 8.2.3 Flow test: Use a leak meter to measure the flow rate and copper sleeve thickness under load operation of 3hmN. 6.2.4 Thickness adjustment test: Compare and confirm the thickness adjustment value and the actual cutting thickness with the requirements of Table 1. 6.2.5 Test for lubrication accuracy (back) gradually. 6.3 Mechanism performance test
6.3.1 Blade dynamic test: After cutting off the power supply, measure the gap between the blade and the bottom of the medicine mouth with a ruler, apply red moonwood to the bottom edge of the medicine mouth at the contact point of the force line, and observe manually. 6.3.2 Inch forging tightness test: Determine by sensory perception and confirm the solid performance. 3.3.3.3.4.1 Hardness test: Use the hardness tester to measure the hardness according to the indication position of the agent 1. Weighted average. The width of the blade and the effective length of the blade are measured with a ruler. 6.3.4.2. Roughness measurement: According to the sliding surface of Figure 1 and the provisions of CT/T600.1, the sample comparison method is used for measurement. 6.3.4.3. The angle of the blade and the parallelism of the blade are measured on the positive plate with an angle ruler and a dial. 43 JB/T 200432004 70~ 23
6.4 Safety performance test
6.4.1 Safety test of exhaust system:
Figure 1 blade
Limited test points
B.4.1.1 The continuity, insulation resistance and withstand voltage reduction test of the protective grounding circuit of the electrical system shall be tested in accordance with the provisions of 19.2, 19.3.19.4 of GB5226.1-2002 respectively. 6.4.1.2 The requirements for the protective grounding switch, indicator light, display, wiring, marking signs and item codes of the electrical system shall be checked in accordance with the provisions of Chapter 8, 3.10, 2.10, 3.14 and Chapter 17 of CB5226.1-2K2 respectively. 6.4.2 Safety quality inspection:
6.4.2.1 Daily inspection of the position of the safety warning sign. B.4.2.2 Daily inspection of the firmness of the protective cover net of the induction, 7 Inspection rules
7.1 Inspection classification
Product inspection is divided into factory inspection and type inspection. 2 Factory inspection
7.2.1 Products are inspected item by item according to the requirements of Table 2. After passing the inspection, they are allowed to enter the factory and accompanied by a product certificate. Table Factory inspection items
Items from the United States
One amine performance
Soil welcome sleep
7, 2.2 Judgment rules:
Inspection items
5.1.1, 5.2.1, 5.2.3. 5.4.1.4. 5.4.1.8, 5.4.2.23.2.4, 5.3 1, 5.3.4.1, 5.4.1.1~ 5.4.1.3 If a product fails to meet certain requirements during inspection, it is allowed to be retested after adjustment. If it still fails, it is judged as unqualified. 7.3 Type inspection 7.3.1 Type inspection should be carried out when one of the following circumstances occurs: When a new product or a test product is transferred to production for trial production and type identification: 5) When the design, process or materials used of the product involve important performance or major improvements, and the product is put into production more than once every two years:
1) When the inspection result is significantly different from the last type inspection: e) When the national quality supervision agency proposes type inspection requirements 7.9.2 Sampling:
The samples for type inspection shall be randomly selected from the products that meet the factory inspection requirements for inspection. 7.9.3 Regulations:
JB/T 20043—2004
In the type test, if any one of the electrical safety performance items of protective earthing circuit continuity, electrical connection and durability fails to meet the standards, the product shall be deemed to have failed the type test. If other performance items fail to meet the standards, the failed items shall be retested twice. If the failed items still fail to meet the standards, the product shall be deemed to have failed the type test.
B Marking, packaging, transportation and storage
8.1 Marking
B.1.1 The marking shall comply with the provisions of CBrT13306. It should include the following contents: a) Name and model;
hi trademark;
manufacturer: new or address;
production terminal number, date of shipment
6) adopted standard number;
equipment deadweight (kg)
B.1.2 The transport mark should comply with the requirements of T191, including: a) collection unit and location;
name and verification number;
) shipping unit and delivery point;
) "center of gravity", "center of gravity" (center of gravity); appearance and electrical connection (k)).
B.2.1 Product packaging shall comply with the provisions of GB13384. ||tt| ... 8.3 Transportation
Products should be firmly fixed on the transport platform. Rolling, bumping and pressure change are prohibited. 8.4 Storage
Products should be placed flat in the warehouse. Reversing or stacking is not allowed. When stored outdoors, they should be covered with rainproof covers.2. The transport mark should comply with the requirements of T191, including: a) Collection unit and location; b) Name and verification number; c) Shipping unit and delivery point; d) “Center of gravity”, “center of gravity”, “center of gravity”, “center of gravity”, “shape and shape” (k)). B.2.1 Product packaging should be in accordance with the provisions of GB13384. 2.2 The packaging box should be accompanied by 7 documents: a) Product certificate of conformity; h) Packing list; h) Special tool list; e) Equipment basic drawing; e) Product instruction manual.
8.2.3 Product manual (in accordance with the provisions of R0069.1, including: product name, model, manufacturer's address, zip code and contact number; implemented product standards
main use, structure, performance, operating precautions, warnings and prompts, instructions for protecting operators and product safety measures;
JE/T20043-2004
d) Explanation of the final shape, symbols and abbreviations in the specifications:) Installation and commissioning methods, repair and maintenance methods, fault analysis and elimination. 8.3 Transportation
The product should be firmly fixed on the transport tool. Rolling, collision and pressure change are prohibited. 8.4 Storage
The product should be stored flat in the warehouse. It is not allowed to be upside down or stacked. When stored in the open air, it should be covered with a rainproof shelter.2. The transport mark should comply with the requirements of T191, including: a) Collection unit and location; b) Name and verification number; c) Shipping unit and delivery point; d) “Center of gravity”, “center of gravity”, “center of gravity”, “center of gravity”, “shape and shape” (k)). B.2.1 Product packaging should be in accordance with the provisions of GB13384. 2.2 The packaging box should be accompanied by 7 documents: a) Product certificate of conformity; h) Packing list; h) Special tool list; e) Equipment basic drawing; e) Product instruction manual.
8.2.3 Product manual (in accordance with the provisions of R0069.1, including: product name, model, manufacturer's address, zip code and contact number; implemented product standards
main use, structure, performance, operating precautions, warnings and prompts, instructions for protecting operators and product safety measures;
JE/T20043-2004
d) Explanation of the final shape, symbols and abbreviations in the specifications:) Installation and commissioning methods, repair and maintenance methods, fault analysis and elimination. 8.3 Transportation
The product should be firmly fixed on the transport tool. Rolling, collision and pressure change are prohibited. 8.4 Storage
The product should be stored flat in the warehouse. It is not allowed to be upside down or stacked. When stored in the open air, it should be covered with a rainproof shelter.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.