Some standard content:
ICS61.060
Chemical Industry Standard of the People's Republic of China
Sports shoes, rain boots (shoes)
(2001)
Published on 2002-01-24
Implemented on 2002-07-01
Published by the State Economic and Trade Commission
Registration No.: 10148-2002
HG/T2020-2001
This standard layer This standard JISS500:-1992 is a non-equivalent standard for the revision of the recommended chemical industry standard HG/20201991 "Colored Shoes (temporary)". The main technical differences of this standard 115S5005-1992 are the deformation, cold resistance, addition and reduction (existence), fabric properties, dyeing rate and other performance indicators in the industrial standard. A detailed description of the appearance quality is given. The main technical differences of this standard HG/2020-1951 are ：- The tensile strength aging performance retention rate has been added as a type test item. The rubber (skin) and outer sole thickness requirements and water resistance test requirements have been added. For the external quality inspection, the use of (B26U& color change evaluation color sample card as the color difference evaluation period has been added. From the date of implementation, this standard will replace HG/T202).-1931 This standard was proposed by the former State Petroleum and Chemical Industry Bureau. This standard is issued The National Standardization Technical Committee for Rubber and School Products is under the jurisdiction of the Rubber Fusion Technical Committee. The parties involved in this standard are: the National Bureau of Exit and Entry Inspection and Quarantine of the People's Republic of China, Jiangsu Shuangshi Shoes Co., Ltd. The main drafters of this standard are: Fei Yue, Sun Changqing, Tu Wuxian, Lai Chong, Yang Laliang. This standard was first published in 1597.
1 Fanyuan
Chemical Industry Standard of the People's Republic of China
Colored Rain Boots (Shoes)
Culur Rain rubber boots[shhes]FG/T 2020—200t
Replaces HT2620-1991
This standard specifies the requirements, test methods, inspection rules, marking, packaging, transportation and storage conditions of colored rubber boots (groups). This standard is applicable to two batches of <frogs> made of colored rubber materials for general waterproof wear. This standard is not applicable to rubber boots (shoes) with acid, acid, explosion resistance, industrial and mining and other special uses. 2 Reference standards
The texts contained in the underlined standards are the provisions of this standard through reference in this standard. At the time of publication of this standard, all versions are valid. All standards will be revised. Parties using this standard should explore the possibility of using the following standard versions: 2501995 Color sample card for evaluating color change (idtS0)105-A02:1993) GB/T 528—1998
Test method for tensile stress-strain of thermoplastic rubber or thermoplastic rubber (egISO: 1D94GT/T531—199S
GB/T 53219$?
Test method for indentation hardness with a cavity extraction hardness tester (idt1S7619: 1586)Test method for adhesion strength between thermoplastic rubber or thermoplastic rubber and fabric (S1993GB/T1680—1998Test method for wear resistance of thermoplastic rubber (using a Kron abrasion machine)GH/I2941
Standard temperature, humidity and time for environmental conditioning and testing of rubber or sampleBefore enjoying 1/2.
Gui category is limited to one place, the sail comes to manage four places
pregnant curve is allowed, other mail is not surprising according to more than 2.5 una
surface fiber
of the epidemic tracewww.bzxz.net
this (shengsheng deke
and the inner bottom shell
acid adjustment, piece line
shengke dehollow
high false unevenness and air rise
outsole inner bottom brain hollow
outsole single
outsole degree package collection (outside)
outsole post epidemic up
outsole medical school suspension, new, pores
creative selection has pores
consequences of flowers according to the length square
light rate uneven
super coating, dense||tt ||Hope you
Printed mosquito small clear
Recommend according to the type
Imperfect
Imperfect
Imperfect
HG:/T2020—2001
Table)
Appearance quality basic requirements
(Diameter) part is not only, other parts are allowed to be more than 25m in length, only two parts are allowed in the same part
, and more than 25
:url\, the length of the same part is limited to one part, and the number of parts is limited to one part. The curved part is not difficult to be laid, and the lower part is checked and more than 1. 5. Treatment of ra, silicon gland - place, this type of limit two places area not more than 1500, mouth and
can be bent must not have
to calculate the area not more than 400m:bl
separately calculated the same table not more than 3Un
not this limit after processing)
inner bottom edge media said air flow not more than 5m
surface not more than 200, high and low not let
2 nini limited to three places
surrounding area 2uDnus less than one place
not push female
over magic not more than u
slightly not obvious
outside the family package around the strip not less than 2 two outside the year not more than 2mg
area not more than iU rmr Yin one place, this
This clear
bend part is not applied, other chapter goods straight light not bottle qualified products
good standard length exceeds · etc. products mother set old · Han award limit dry four places
can (carve) some parts to double not more than 25mm, limit
, or other parts area does not exceed SDm, limit two places, general limit three places
Li curved parts are not allowed, other parts inspection straight does not exceed 2 Add m, Pa Yang two places, on the Yang four places the surface period does not exceed 40, busy can not be forbidden
in the comb door
period two can not exceed 600m1 yuan
cumulative and the surface is not shorter than 60nmm
does not affect the wearer
inner bottom edge to take off the width is not thicker than 8mm people are not allowed to go down
area does not exceed 400, high and low does not exceed
2 m three places
length [ODum below
depth does not exceed 1: length does not exceed [G:mm, net one place
depth does not exceed
m, limited to one place
does not seriously affect the appearance
does not affect the current
surface does not exceed 4D m*, one place in the warehouse, the flower is relatively clear
No curved parts are allowed, the other parts are not more than 3m in diameter, and the height or depth is not more than the external thickness? mm, limited to two places, the high-efficiency depth does not exceed 1/3 of the outer bottom reading
1/3 of the reading
in the color does not exceed 1 mm, limited to the same makeup () equidistant baby number is not less than 795, not less than z195, not more than 5mm
3m said pump, no obvious
oil adjustment is not allowed, oil shortage is not lower than the general mouth, but above: the front fast is not sexual with Hongshu belt position 20L or less, sexual two places, or the spoon meter surface is not more than ℃T4 road
1m Yuanming
do not use type view
symmetrical, no broken line, no bulging season
effective upper mouth height does not exceed 5mm,
no girl m
skin does not have, through the ring does not
1uu does not exceed n
diameter does not exceed 2 mm.Limited person
same pair of shoes, base A, not less than 195, not less than 1819, not more than 1m sight distance, sales cloth not purchase
-thousand seriously affect the appearance
length m below the limit or the cumulative area can not exceed
207, but each order before applying for ten boots, im must be flat, the size has a difference
the method does not produce double images, beautiful
not seriously affect the appearance
same pair of shoes, the upper mouth height does not need to exceed 1℃ninl.Class does not exceed mm
said change The length is not more than 10 grids, the depth is not more than one, the joint is reduced to mm
No one has
Note: The quality defects not in this table are connected to the items of low processing, production weight, and the impact on the appearance of the joint should be listed as unqualified products. 1
6 Test method is suitable for
HG/T2020-2001
6.1 General requirements for the test method of vulcanized rubber cavity type resistance performance test method are in accordance with the requirements of TIG Ting 2198, and the finished product sample can be cut along the outer bottom.
6.2 Test conditions for rubber samples
The test objects of rubber samples shall be carried out in accordance with the provisions of CB/T2941, and the effective time of the sample before the test shall not be less than 6bh. 6.3 Determination of tensile properties of vulcanized rubber
The tensile properties of vulcanized rubber are determined in accordance with GB/T523. The outer and upper surfaces of the shoe are all tested using 6-gauge cutting tools. When the specimen thickness does not meet the requirements of the test method standard: the actual thickness of the test piece is tested. 6.4 Determination of the wear resistance of vulcanized rubber
The wear resistance of vulcanized rubber is determined in accordance with GB/T1689. When the test piece is not long enough, it can be overlapped in the outer direction. When the test strength does not meet the test evaluation standard, the actual thickness of the test piece is changed for testing. 6.5 Physical change test
The hardness test is carried out in accordance with R/T3. If the thickness of the test piece does not meet the requirements, it can be stacked until the test strength requirements are met.
6.6 Intermittent strength test
The adhesion strength test is carried out according to H/T538. Sample location: Take two pieces of shoes, and collect them in two directions. The width is 10mm, and the length is 100-200mm. Cut the test piece along the effective width of the sample to 40~b0mm (that is, the effective test length of the sample>). Then use a knife to cut the test piece (shoe) from the rubber along the effective width of the sample. 6.7 Transfer elongation test
6. 7. 1 Test piece
Cut a test piece with a length of 120~125mm and a width of (1C ± 0.2)mm, which is the thickness of the original finished product, and mark two marking lines with a distance of (100 ± (.5)Trum on the finished piece
6.7.2 Test steps
After adjusting the clamps of the tensile machine so that the distance between them is 100, the test piece is precisely controlled under the test conditions, and the lowering speed of the head holder is <10)-10)mm/min. When the test piece is stretched to 7 degrees and the first crack appears, it is tested. Make two tests for each pair (load) and take the average value.
6.7.3 The result shows that the film elongation rate is calculated in %) according to formula (1),
is the distance between the original marking lines of the film, m
where: 1.
When the first crack appears on the aging film, the distance between the marking lines is mm. 6.8 Aging test
Perform according to the provisions of GR/T5512. The aging test conditions are (7C+1)℃×72h. The aging time is 4-24b. The index strength after aging is measured and compared with the unaged test piece to calculate the aging performance retention rate P[must]: The tensile strength aging performance retention rate PI%1 is calculated according to formula (2): Px100
Wherein: A—tensile strength of the sample after aging, MPa1(); tensile strength before aging, MI\a,
Aging performance retention rate () value. Accurate to the desired digit. (2)
6.9 Determination of the degree of corrosion
6.9.1 Determination of external corrosion resistance
HG/T2020
Take the outer bottom of the sample, scratch the edge of the outer point, and separate it from the core to obtain the (sexual) base glue! , the thickness of the rubber surface is measured by the vernier scale, and the thickness of the most important point is taken as the thickness of the previous paragraph, followed by the recommended value, and the thickness of the most important point. The minimum value is taken and the decimal point is retained.
6.9.2 Determination of the thickness of the boot (carrier) surface
Cut the construction (station) surface from the test boot (frog), and obtain the (wang) Li rubber rise: Ⅱ Rubber thickness measurement wine Yue (Mu) surface thickness: take the minimum value, retain one decimal point. 6.10 Water resistance test
According to the provisions of HG/T3664:
6.11 Appearance quality
Appearance quality The color difference test method of the whole batch (carrying) of the net parts shall be carried out according to the provisions of G products: 7 Inspection rules, labels, packaging, transportation, storage inspection rules, labels, packaging, transportation, and other regulations of H/2-03 for rubber soles and rubber shoes. The outer sole thickness test shall be carried out according to 3.2.1.2 of TIG/T2403-792, and the aging test and water resistance test shall be carried out according to T1G/T2103--15923.9. Each pair of packaging shall have a standard number, 23
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.