GB/T 5330.1-2012 Industrial wire screens and wire braids, selection guide for mesh size and wire diameter combination, Part 1: General GB/T5330.1-2012 |tt||Standard compression package decompression password: www.bzxz.net
This part of GB/T5330 specifies the mesh size and wire diameter combination of industrial wire screens and wire braids. This part applies to industrial wire screens and wire braids.
GB/T5330 "Guide to the selection of mesh size and wire diameter combination for industrial metal screens and metal wire woven nets" is divided into 3 parts:
———Part 1: General;
———Part 2: Industrial metal wire woven square hole screen;
———Part 3: Pre-bent metal wire woven square hole screen. This
part is the first part of GB/T5330.
This part is drafted according to the rules given in GB/T1.1-2009.
This part replaces GB/T5330.1-2000 "Guide to the selection of mesh size and wire diameter combination for industrial metal screens and metal wire woven nets". Compared with GB/T5330.1-2000, the main technical content has not been changed.
This part is redrafted to modify ISO 4783-1:1989 "Guide to selection of mesh size and wire diameter combinations for industrial use - Part 1: General".
This part has technical differences from ISO 4783-1:1989. The clauses involved in these differences have been marked with a single vertical line (∣) in the outer margin. The technical differences and their reasons are as follows:
———Regarding the normative reference documents, this part has made adjustments with technical differences to adapt to China's technical conditions. The adjustments are concentrated in Chapter 2 "Normative Reference Documents". The specific adjustments are as follows:
● GB/T10611 Industrial mesh marking method and mesh size series (ISO2194:1991, MOD);
● GB/T19628.2 Industrial metal wire mesh and metal wire woven mesh mesh mesh size and metal wire diameter combination selection guide Preferred combination selection of metal wire woven mesh (ISO4783-2:1989, MOD);
———Modified the numerical provisions of the deformation coefficient f of pre-bent and pressure-welded metal wire in Chapter 5 for ease of operation;
———Modified the title and name of the figure in Chapter 6;
———Deleted the article notes and Table 2 in Chapter 5.
For ease of use, this part has also made the following editorial changes:
———Added Appendix A.
This part was proposed and managed by the National Technical Committee for Particle Characterization and Sorting and Screen Standardization (SAC/TC168).
Drafting units of this part: China Machinery Productivity Promotion Center, Xinxiang Bashan Precision Filter Material Co., Ltd., Anping County Anhua Hardware Mesh Products Co., Ltd.
Main drafters of this part: Yu Fang, Liu Heqing, Xu Lanhui.
The previous versions of the standards replaced by this part are:
———GB/T5330.1-2000.
The following documents are indispensable for the application of this document. For any dated referenced document, only the dated version applies to this document. For any undated referenced document, its latest version (including all amendments) applies to this document.
GB/T5330 Industrial metal wire woven square hole screen
GB/T10611 Industrial net marking method and mesh size series (GB/T10611-2003, ISO2194:1991, MOD)
GB/T13307 Pre-bent metal wire woven square hole mesh
GB/T19628.2 Industrial metal wire mesh and metal wire woven mesh mesh size and metal wire diameter combination selection guide Preferred combination selection of metal wire woven mesh (GB/T19628.2-2005, ISO4783-2:1989, MOD)
JB/T7860 Industrial metal wire

ICS19.120
National Standard of the People's Republic of China
GB/T 5330.1—2012
Replaces GB/T5330.1—2000
Industrial wire screens and woven wire cloth--Guide to the choice ofaperture size and wire diameter comhinations-Part 1 : Generalities(IS0 4783-1:1989,M0D)
2012-09-03 Issued by
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Standardization Administration of the People's Republic of China
2013-03-01 Implementation
People's Republic of China
National Standard
Mesh size and wire diameter combination of industrial wire screens and wire woven meshes
Selection guidewww.bzxz.net
Part 1: General
GB/T 5330.1-—2012
Published and distributed by China Standard Publishing House
No. 2, Hepingli West Street, Chaoyang District, Beijing (100013) No. 16, Sanlihe North Street, Xicheng District, Beijing (100045) Website spc.net. cn
Editorial Office: (010)64275323Distribution Center: (010)51780235Reader Service Department: (010)68523946
Printed by China Standards Publishing House, Qinhuangdao Printing FactoryDistributed by Xinhua Bookstores in various regions
Format 0×12301/16
Print Sheet 1. 25
Word count: 32,000 words
First edition in December 2012
Revised printing in December 2012
Price: 21.00 yuan
Book number: 155(166:1-45867
If there is any printing error
Replaced by our publishing center
Infringement will be investigated
Copyright reserved
Report phone: (010)68510107
GB/T 5330.1—2012
GB/T5330 "Guide to the selection of mesh size and wire diameter combination of industrial metal wire screens and metal wire woven nets" is divided into 3 parts:
Part 1: General rules;
…-Part 2: Industrial metal wire woven square hole screens; Part 3: Pre-bent metal wire woven square hole screens. This part is the first part of GB/T5330.
This part is drafted according to the rules given in GB/T 1.1—2009. This part replaces GB/T5330.1200C "Guide to the selection of mesh size and wire diameter combination of industrial metal screens and metal wire woven nets". Compared with CB/T 5330.1-2000, the main technical content has not been changed. This part uses the redrafting method to modify ISQ 4783-1:1989 "Guide to the selection of mesh size and wire diameter combination for industrial wire screens and wire woven meshes Part 1; General". This part has technical differences with IS04783-1:1989. The clauses involved in these differences have been marked with a vertical single line (!) in the outer margin. The technical differences and their reasons are as follows: Regarding the normative references, this part has made adjustments with technical differences to adapt to my country's technical conditions. The adjustments are concentrated in Chapter 2 "Normative References". The specific adjustments are as follows: GB/T10611 Industrial Net Marking Method and Mesh Size Series (ISO2194: {991, MOD) GB/T 19628.2 Industrial Metal Wire Mesh and Metal Wire Braided Net Mesh Size and Metal Wire Diameter Combination Selection Guide Preferred Combination Selection of Metal Wire Braided Net (ISO1783-2: 1989, MOD); Modified the numerical provisions of the deformation coefficient f of pre-bent and pressure-welded metal wire in Chapter 5 for easy operation; Modified the title and name of the figure in Chapter 6:
Deleted the article notes and Table 2 of Chapter 5. For ease of use, this part also made the following editorial changes: Added Appendix A.
This part is proposed and managed by the National Technical Committee for Particle Characterization and Sorting and Screen Standardization (SAC/TC168). The drafting units of this part are: China Machinery Productivity Promotion Center, Xinxiang Bashan Precision Filter Material Co., Ltd., Anping County Anhua Hardware Mesh Products Co., Ltd.
The main drafters of this part are: Yu Fang, Liu Heqing, Xu Lanhui. The previous versions of the standards replaced by this part are: -GB/T5330.1—2000
1 Scope
Combination of mesh size and wire diameter for industrial metal wire screens and metal wire woven nets
Selection guide Part 1 General
GB/T 5330.1—2012
This part of GB/T5330 specifies the combination of mesh size and wire diameter for industrial metal wire screens and metal wire woven nets. This part applies to industrial metal wire screens and metal wire woven meshes. 2
Normative referenced documents
The following documents are indispensable for the application of this document: For any referenced document with a date, only the version with the date applies to this document. For any undated referenced document, the latest version (including all amendments) applies to this document. GB/T5330 Industrial metal wire woven square hole screen GB/T10611 Industrial net marking method and mesh size series (GB/T10611-2003, ISO2194:1991MOD) GB/T13307 Pre-bent metal wire woven square hole net GB/T19628.2 Guide to the combination selection of mesh size and wire diameter for industrial metal wire mesh and metal wire woven mesh Preferred combination selection of metal wire woven mesh (GB /T19628.2—2005,ISO4783-2:1989,MOD)JB/T7860 Industrial Metal Wire
3 Marking
Industrial Metal Wire Screen Rental Metal Wire Woven Mesh should be marked in the following order (in the list): mesh size;
b) metal wire diameter d;
metal wire material;
d) weaving type, see the provisions of GB/T5330 and GB/T13307. 4 Combination of mesh size and metal wire diameter
The mesh size is in accordance with the provisions of GB/T10611. Table 1 gives several matching metal wire diameters, and its values ​​are in accordance with the provisions of JB/T7860, and the corresponding approximate value of the percentage of the screening area of ​​the metal wire screen is indicated. The screening area percentage can be calculated according to formula (1): A,-100
wherein:
screening area percentage, %;
mesh size, in millimeters (mm); d—wire diameter, in millimeters (mm). Note: For the specifications selected from Table 1, additional data may be provided, such as mass per unit area, number of meshes per unit length (1)
GB/T 5330.1—2012
Percentage
Combination of mesh size and wire diameter
Mesh size
106100
10. 010. 0
Wire diameter d
Unit: mm
Percentage
Table 1 Combination of mesh size and wire diameter (continued) Mesh size
4. 003. 55
Wire diameter d
GB/T5330.1—2012
Unit: mm
: 4, 00
GB/T5330.1-2012
Percentage
1. 80 | 1. 80
Table 1 Combination of mesh size and wire diameter (continued) Mesh size
11.8[11.2
Wire diameter d
1. 251. 251.12
6.30; 5. 60
1. 00 0. 9000. 900
Unit: mm
1. 80: 68
Percentage
Percentage
0,8000.7100.710
Combination of mesh size and wire diameter (continued) Mesh size w
12.511.811.210.6
Wire diameter d
GB/T 5330.1—2012
Unit: meter
Table 1 Combination of mesh size and wire diameter (continued) Mesh size
Wire diameter
Unit: meter
3.753.553.35
GB/T 5330.1--2012
Percentage
Combination of mesh size and wire diameter (continued) Mesh size
7.1 G.76. 3
Wire diameter
Unit: millimeter
Percentage
Table 1 Combination of mesh size and wire diameter (continued) Mesh size u
2. 5 2, 362,24
Wire diameter
GB/T 5330,1—2012
Unit: meter
1. 4 1. 32
.c.355
GB/T5330.1—2012
Percentage
Table 1 Combination of mesh size and wire diameter (continued) Mesh size
2.36.2.24
Wire diameter d
Unit: millimeter
.0.710
Percentage
1. 25 1. 181.12
Table 1 Combination of mesh size and wire diameter (continued) Mesh size u
Wire diameter
GB/T 5330.1-2012
Unit: mm
30. 6 / 0. 560. 53
.c.224
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.