Some standard content:
Industry Standard of the People's Republic of China
QB1769~-1801-93
Standard for Spice
(Product Standard)
Published on April 29, 1993
Implemented on December 1, 1993
Published by the Ministry of Light Industry of the People's Republic of China
Main content and applicable scope
-TKATKACa
Industry Standard of the People's Republic of China
QB1791-93
This standard specifies the technical requirements, test methods and inspection rules for ethyl vanillin. This standard is applicable to the vanillin derived from o-ethoxy vanillin with p-nitrosodibutyl ether and hexamethylenetetracycline as raw materials.
2 Reference standards:
CB/T144.14.3 Color determination of spices
GR/T16454.2 Determination of aroma of spices
GB/T14457.3 Determination of new aroma of isolated and synthesized spices GB/T 14467,1
Monoisocyanate and synthetic fragrance ethanol decomposition must be determined by GB11589 Monoisocyanate and synthetic fragrance column gas phase analysis general product chemical name, molecular formula, structural formula, molecular weight Chemical name B ethoxylated 4·hydroxyethyl aldehyde Molecular formula: H.nO,
Structural formula
Year: 16618 (according to the 1987 International Atomic Energy Agency technical requirements
4.! Color: light gray or sticky powder, 4.2 Check whether the gas is filled with some gas, relatively 4.3 Melting point ()
76.9-78.0.
4. Density (2)
4.5 Severe loss of electricity (%)
5 Test method
5.1 Test method for free
JGB/T14454.3
1 The sample is completely dissolved in 95% () ethanol 3ml, and the solution should be clear.
Ministry of Light Industry of the People's Republic of China 1993-4-29 approved 1993-12-01 implementation
5.2 Evaluation of aroma
See GB/T 14464.2
6.3 Determination of melting point
MGB/T 11d57.3
QB 179193
And the gas chromatograph of the determination of the temperature of the sample is shown in the Appendix. .5.4 Determination of melting point, 25℃
See GB/T 14457-1,
5.5 Determination of dry tip straightness
5.5.1 Apparatus and reagent
1 Explosive device quality: diameter 2~24;
Butyl silica gel.
5.5.2 Working procedure
Put the color changing agent in an oven at 120℃, then cool to room temperature and take about 2-3 samples (accurate weighing 0.0002%) from a pre-weighted grid, so that the sample thickness does not exceed 1. Then put the bottle and the cover in a dryer for 4 hours, and cover the cover when taking it out, and weigh it repeatedly until the sample is fixed.
The test pressure is calculated by the following formula (A), A()
,-drying tip, dead
, the bottle of the sample and the weighing bottle, more, the sample and the weighing bottle are directly heated, more, W-the amount of the sample: more.
The allowable difference of the parallel test results is 1.2%. 6 Inspection period
6.】The number of finished products of Xianglantai should be inspected by the inspection department of the manufacturer to ensure that the products leaving the factory meet the original standards and sign. Each batch is out! All products should have quality certificates: Contents include: manufacturer, product name, trademark, production date (batch number, net number, product quality certificate and this standard. 6.2 The inspection unit has the right to inspect the received products according to the provisions of this standard to see if they meet the requirements of this standard. The batch number is used for acceptance, and different batch numbers are inspected separately: 6.3 For each batch of packaging units, one sample is selected for testing if it is less than 1%, and samples are selected for testing if it is more than 100. Use a sampler to evenly distribute the samples from each packaging unit. Take 30-100 samples of oil, and put all the collected samples into the sample collection for research and analysis. Take 5-100 samples and put them into two bottles with different differences. The name of the product, batch number, and the date of collection shall be marked. One bottle shall be used for inspection and stored for future reference. .4 If one of the indicators in the acceptance results does not meet the requirements, the manufacturer may add a new sample for re-inspection together with the manufacturer. If one of the indicators still fails to meet the requirements after the overall results, the batch of products shall be deemed unqualified. -- 13 --
Q8 1791—93
TKAONTKAawwW.bzxz.Net
6.5 When the supplier has any disagreement with the product quality, the two parties can negotiate to resolve the issue or invite a statutory inspection agency to make an arbitration, and the cost shall be borne by the supplier.
6.B Color, aroma, tower temperature, solubility are factory inspection indicators. Drying loss is a type inspection indicator and shall be tested every time.
Marking, packaging, transportation, inspection, storage
7.1 The supply of ethylene should be packaged in a large-mouthed zinc-sensitive iron drum sealed with ethylene. Cardboard or tinplate, polyethylene bag should be tightly sealed. The outside of the package should be marked with: manufacturer name, product name, standard, batch number, recycling, date of publication and this standard deviation. If the ordering unit has special requirements, it can be coordinated with the manufacturer. 7.2 Ethyl vanillin should be stored in a dry and ventilated warehouse to avoid contamination by foreign air. During transportation, it should be lightly packed and transported to prevent sun exposure and contamination.
7.3 Under the condition of meeting the specified storage conditions, packaging quality and technical requirements, the shelf life of this product is one year. .- 4
Al说器
Q8 1791-93
Appendix A
Determination of ethyl vanillin content Gas chromatography-mass spectrometry Internal normalization (Taiwan version)
A.1 Colorimeter, recorder and microprocessor shall be in accordance with the provisions of GB11539, block sleeve ±k2~8m, inner diameter ~4mm,
same as SE3,5-1ChramasarhAWDM6~日上. A1.3 Detector
On fire A2 Operating Conditions A2.1 Temperature control furnace: linear range: 200 °C/min: 80 °C/min: 240 °C/min carrier gas flow rate: 25 ml/min. A3 Determination of Column Efficiency A3.1 Chemical Properties Test: Carry out the test in accordance with the method specified in B11539, Section B.1. A3.2 Column Efficiency: Determine the column efficiency in accordance with the method specified in B11539, Section 8.2. A4 Determination Method: Perform the internal normalization test in accordance with the method specified in GB11539, Section 10.1. A5 Heavy load and result change
According to GB1159 core 11+1, it meets the requirements. —56-
Additional explanation,
QB 179193
This standard is proposed by the Ministry of Light Industry. This standard is approved by the State Administration of Chemical Industry. -KAONrKAca-
The standard is drafted by Jiaxing China Chemical Industry General, Jilin Chemical Industry Company and the Institute of Light Industry Science of the Ministry of Light Industry.
Who drafted this standard: Cao Zhonglin, Wu Guojun, Xu Pin, Li Meiyu. Since the implementation of this standard, the original Ministry of Light Industry standard 6-ethyl vanilla case D6
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.