JB/T 3555.1-1999 This standard is a revision of JB 8088-95 "Precision of woodworking band saws and racers". During the revision, only editorial changes were made according to relevant regulations, and the technical content remained unchanged. This standard specifies the requirements and inspection methods for the geometric accuracy and working accuracy of woodworking band saws and racers. This standard applies to woodworking band saws and racers. It does not apply to joinery band saws and horizontal woodworking band saws. This standard was first issued on March 13, 1989 as GB 10956-89 and was adjusted to JB/T 8088-95 in 1996. JB/T 3555.1-1999 Precision of woodworking band saws and racers JB/T3555.1-1999 standard download decompression password: www.bzxz.net

[C5 79,120.10
Machinery Industry Standard of the People's Republic of China
JR/T3555.1—1999
Woodworking Band Saw Machine and Car
1999-05-14 Issued
National Bureau of Machinery Industry
200-1-01 Implementation
JB/T3S55.1—1999www.bzxz.net
This standard is a revision of JB/T8088—95 "Precision of Woodworking Band Saw Machine and Car". Only the revision is made according to the relevant regulations, and the technical content is not changed.
This standard replaces JDT808895 from the date of implementation. The standard is proposed by the National Technical Committee for Standardization of Woodworking Machine Tools and Cutting Tools. This standard is owned by Fuzhou Woodworking Machine Tool Research Institute, and the responsible drafting unit is Fuzhou Machine Tool Factory. The main drafters of this standard are Ming Rongduo and Guan Guoyi. This standard was first issued in March 1989.
Machinery Industry Standard of the People's Republic of China
Precision of hydraulic band saws and running machines
This standard specifies the requirements for the geometric precision and working precision of woodworking band saws and running machines. 『RT 3555.1--1999
Replacement 808895
Inclusion standard applies to - 1 band saws and working machines without belt chains and external belt chains: Cited standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. This standard is published for, and the versions shown are valid. New standards will be revised. The latest versions of the following standards shall apply to all standards. Note: JT4171-1999 Machine tool precision inspection code
3-31 This standard refers to JB/T417
3.2 Before inspecting the accuracy of the machine tool, refer to JB/T4171-1999 3.: Adjust the installation level of the machine tool, place the spirit level in the center of the workbench in the longitudinal direction of the bed, and the water level reading shall not exceed 0.10100: 3.3 The accuracy inspection sequence listed in this standard does not represent the actual inspection sequence. For the purpose of installation and inspection, the inspection method and inspection method shall be controlled in the order of the object. 3.4 The actual measured length shall be consistent with the length specified in this standard. At the same time, the length that can be measured shall be converted according to the general requirements of this standard. The minimum calculated negative number shall be 0mm4. Inspection of geometric accuracy of the machine. The geometric accuracy inspection is as follows: Approved by the State Machinery Industry Bureau on May 14, 1999. Inspection sample of radial direction of the pulley. IE1759. Small device. Force method version. FBT1TI1999. There are some provisions. 2000-01- Non-implementation. [H/T 3555.1-1999
Table 1 (continued 1
Test items-
norm
direction
b
required
good
pregnant
board||1
net
board
[.Working
>63(1--1250
>6.10-1250
30K length
.10.14
.117:1
standard
4 1.2 2.1
4.2.1.2.2
Note: Not applicable to the effect of F belt
report
4.7.1 2.2.2
Zhengning Bank is the most sensitive and sensitive to the effect of small bones. Each position
is tested according to the limit
juice: small work belt
IB/T 3555.1—1999
Short monitoring items
Pot strip surface 71
Vertical point between the report
Duty display and actual design
Three-row section of aluminum strip
For light drop: the surface
In the three lengths
Aerospace Fangda Science
JBT41TI—199S
In the relationship intersection
1.7.1.2.2.2
14.2.2.2.
4.7.1.2.2 2
5 Work accuracy inspection
Work objects to be inspected are shown in Table 2.
Test quality
Standard with telephone
JB/T3S55.1—1999
Table 1 (study)
Inspection items
Feeding length ratio accuracy
Penalty measurement
Test material
Water content
Technology is greater than
15%
Loose water or
Generally speaking":
With calcium beating
micro storage machine
) control the design to realize the cutting heat to meet the direction
other
eldest daughter x research food × warehouse
is r1000×200×150
the verticality of the reference plane is:
school 8:1000
length 1:0.20
type piece:
small industry 0
length is 2002: surface
the filling degree is not less than 2%
test piece size.
Long Jing Yan Institute
* 2009-200-[50
Test piece:
Small 4 straight price is 30C:
Long 2060
Control test work
Aluminum for thickness
Even groove
Inspection price square
Related meaning
Yang second pass back movement
Amount of actual movement
Note, this is all let than the positive
Saw machine piece element order
Risk law meaning according to
FiT41711yuy
Ancient Guanqin text
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.