title>JB/T 53277-1999 Product quality classification of centrifugal blowers for sintering plants - JB/T 53277-1999 - Chinese standardNet - bzxz.net
Home > JB > JB/T 53277-1999 Product quality classification of centrifugal blowers for sintering plants
JB/T 53277-1999 Product quality classification of centrifugal blowers for sintering plants

Basic Information

Standard ID: JB/T 53277-1999

Standard Name: Product quality classification of centrifugal blowers for sintering plants

Chinese Name: 烧结厂用离心式鼓风机 产品质量分等

Standard category:Machinery Industry Standard (JB)

state:in force

Date of Release1999-12-30

Date of Implementation:2000-06-01

standard classification number

Standard Classification Number:Machinery>>General Machinery and Equipment>>J72 Compressor, Fan

associated standards

alternative situation:JB/T 53277-1994

Publication information

other information

Introduction to standards:

JB/T 53277-1999 Product quality classification of centrifugal blowers for sintering plants JB/T53277-1999 Standard download decompression password: www.bzxz.net

Some standard content:

Machinery Industry Standard of the People's Republic of China
JB/T53277-1999
Centrifugal Blowers for Sintering Plants
Product Quality Classification
(Internal Use)
Published on December 30, 1999
National Bureau of Machinery Industry
Implemented on June 1, 2000
JB/T53277-1999
This standard is a revision of JB/T53277-94 "Product Quality Classification of Centrifugal Blowers for Sintering Plants". During the revision, the original standard was edited, and the main technical content remained unchanged. This standard replaces JB/T53277-94 from the date of implementation. This standard is proposed and managed by the National Technical Committee for Standardization of Blowers. The responsible drafting unit of this standard: Shaanxi Blower (Group) Co., Ltd. The main drafter of this standard: Wang Jianzhuang.
1 Scope
Machinery Industry Standard of the People's Republic of China
Centrifugal Blowers for Sintering Plants
Product Quality Grading
(Internal Use)
This standard specifies the quality grade, sampling and assessment methods of centrifugal blowers for sintering plants. This standard applies to the quality assessment of centrifugal blowers for sintering plants (hereinafter referred to as blowers). 2 Referenced StandardsbzxZ.net
JB/T53277—1999
Replaces JB/T53277—94
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards are subject to revision, and parties using this standard should explore the possibility of using the latest versions of the following standards. 5 Test methods for aerodynamic performance of fans
GB/T1236—1985
GB/T10178-—1988
JB/T7259—1994
Field test of fans
Centrifugal blowers for sintering plants
3 Quality grades of blower products
3.1 Blowers shall comply with the provisions of JB/T7259 and be divided into three grades: qualified products, first-class products and superior products according to their quality level and use value.
3.2 Blower products shall comply with the provisions of JB/T7259, and the assessment items and index requirements of each grade shall be as specified in Table 1. 3.2.1 The aerodynamic performance test of the blower shall be carried out in accordance with GB/T10178, and the modeling test of the blower shall be carried out in accordance with GB/T1236. Its performance deviation shall be as specified in Table 1.
3.2.2 The blower rotor shall be balanced and corrected according to JB/T7259, and its balance quality level shall be as specified in Table 1. 3.2.3 When the blower is subjected to mechanical operation test at rated speed, its vibration value shall meet one of the following two requirements: a) The shaft vibration (displacement peak-to-peak value) level measured near the journal shall be as specified in Table 1; b) The effective value of the vibration velocity at the bearing shall be measured by a contact vibration meter, and its level shall be as specified in Table 1. 3.2.4 The assessment of the first overhaul period shall be as specified in Table 1. It can be determined by the feedback from users of other products in the same series. The number of months is calculated from the date of shipment, and only one of the two indicators of hours and months needs to be met. 3.2.5 The key project qualification rate of blower parts shall reach 100%, and the items are: a) rotor balance quality level;
b) matching size with rolling bearings;
) casting quality of bearing babbitt alloy, and the bonding degree between bearing alloy and housing. 3.2.6 The qualification rate of main items of main parts of blower shall be in accordance with the provisions of Table 1. The main parts are: rotor, seal, bearing and bearing box. The main items are:
a) Dimensions with tolerance grade higher than or equal to IT8 marked with fitting requirements; approved by the State Machinery Industry Bureau on December 30, 1999 and implemented on June 1, 2000
b) Items with geometric tolerances:
JB/T53277-1999
c) Items with surface roughness R value less than or equal to 3.2μm; d) Fitting clearance and contact surface between rotor journal and sliding bearing; e) Clearance between blade profile, air inlet camber profile and sample f) Blade outlet installation angle;
g) Impeller outlet width.
Assessment items
Pressure deviation
Shaft power deviation
Balance quality grade G
Shaft vibration displacement peak-to-peak value (amplitude value)
Effective value of vibration velocity at bearing (RMS value)First overhaul period
Quality rate of major items
Note: Deviation in the table = actual value - standard valueStandard value
Quality index grade
Qualified products
≥12000
Quality grade
≥16000
(within 18 months)
(within 24 months)
Superior products
≥24 000
(within 36 months)
3.3 The main supporting products and purchased parts of the blower, such as prime movers, valves, couplings, rolling bearings, instruments, etc., shall meet the quality level requirements of the blower.
4 Sampling and evaluation methods
4.1 For single-unit products, each unit shall be inspected. For batch-produced products, one unit may be randomly selected for inspection. 4.2 The quality level of the product shall be determined in accordance with the requirements of all assessment items specified in this standard. Otherwise, the lowest indicator shall be used for determination. If an item is missing, the product cannot be determined.
Mechanical Industry Standard
Centrifugal Blower for Sintering Plant
Product Quality Classification
(Internal Use)
JB/T53277-1999
Published and Distributed by Mechanical Science Research Institute
Printed by Mechanical Science Research Institute
(No. 2, Shouti South Road, Beijing
Postal Code 100044)
Format 88 0×1230
1/16 Sheet 1/2
Word count 6.000
First edition in June 2000
Print run 1-500
First printing in June 2000
Price 1000 yuan
99-1616
Mechanical Industry Standard Service Network: http/kvwwJB.ac.cn6661 /
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.