This standard specifies the basic parameters and installation dimensions, technical requirements, test methods, acceptance rules and markings, packaging, transportation and storage of manual concentrated oil lubrication pumps. This standard is applicable to the lubrication system of metal cutting machine tools and forging machinery, and can also be used as a reference for the lubrication systems of other machines. JB/T 8651.1-1997 Machine tool lubrication system components Manual concentrated oil lubrication pumps JB/T8651.1-1997 Standard download decompression password: www.bzxz.net
Some standard content:
Machinery Industry Standard of the People's Republic of China JB/T8651.1J997 Machine tool lubrication system components Manual concentrated oil lubrication pump 1997-08-18 Issued Ministry of Machinery Industry of the People's Republic of China Implementation on 1998-01-01 JD/T65I,11997 This standard is issued by the Standardization Technical Committee of Quanjincheng Cutting Machine Tool, and is under the jurisdiction of Beijing Machine Tool Research Institute of the Ministry of Machinery Industry, Beijing, the Beijing Anti-Chemical Machine Tool Research Institute of the Ministry of Machinery Industry, Duanjiang Yongli Liubian Machinery Runhe Co., Ltd., Beijing No. 1 Machine Tool Factory and Beijing No. 2 Machine Tool Factory. 1 Machinery Industry Standard of the People's Republic of China Machine tool lubrication system components Manual thick oil lubrication pump JB/T 8651.J-1997 This standard specifies the basic parameters and installation dimensions, technical requirements of lubrication systems, inspection and acceptance criteria and standards, including delivery, transportation, storage, etc. This standard is applicable to lubrication systems of metal cutting machines and non-metallic machining centers: Lubrication systems of other machines can be used for reference: 2 Cited standards The following standards contain new provisions, which constitute provisions of the standard through reference in this standard, and are effective when the standard is published or the edition is in force. All standards are subject to revision. Parties using this notation should discuss the possibility of using the latest version of the following standards GB191-00 GB29187 G3 732494 G0/T1310G-S7 J3/T 3257-01bzxz.net /1:4i2198 IB2 16R3 2 T5( 388 ZB JsU UI3-99 Product marking Packaging Calcium slide pin Nakai kelp General lubricant Hangar drop parts packaging General technical generation parts Components and installation model elimination method Bed shot parts: preparation of random technical documents Meeting code identification salt bed cleanliness determination Machine tool access amplification conditions||t t||limit a1, dynamic oil pump model pain judgment mark aNTi number: monitoring type penetration nominal weight: light: UME) product name code: manual type oil hydraulic press - page number: given number 3.2 standard example nominal type tool is 1=10MPl, given number 1, oil plug area 1-0.42 dynamic oil pump marked as manual system SNB-JIJB/T 85].—1!U7 Approved by the Ministry of Machinery Industry in 19818 Implemented on January 1, 1998 4 Basic fees and safety specifications 4.1 Basic parameters are shown in Table 1) Main state teaching number Road oil point Cat soil Shantou economic volume Public secret music Storage and extraction volume Manufactured without spraying connected pipe .4313. 751: FB/T 8651.1-1997 5SNII-1 GSNB-1 0. 42:5. 75.1. 37 3. 42 c. 73 1. 370. 426.73 1.32ex The root torque supplied by the company shall be equal to the ball order 4.2. Installation dimensions are as shown in Table 1 and Table 2) ESNB-1 Decimal code 5 Technical requirements JB/T 8651.1-1997 5. 1 It is allowed to work under an environmental temperature of 0~44℃, and the quality of the material used shall be greater than 285:2,15)g)1/1(1 m for the grease required by GB491, GB192, GB7324. 5.2 The material, processing quality, heat treatment, etc. of the parts shall meet the requirements of the product and the relevant technical regulations. 5.3 The nominal pressure, oil flow capacity, etc. shall not be less than the values specified in Table 1. S.4 Standard and purchased parts shall have product certificates that meet the relevant standards: the appearance is complete, and no defects such as collision, corrosion, and damage shall be allowed. 5.5 5.6 No-load test piece, the sliding pump shall be smooth, and there shall be no obstruction. Under the nominal pressure, the oil outlet shall be normal: 5. 7 During the sealing test: the joints and seals shall not leak. Under the pressure of the ball, the range of each injection port is not less than the range specified in Table 1 below. 5.10 Cleanliness ensures that the amount of foreign matter removed from the internal cleaning of the four plants does not exceed 10cg-5.11 Under the condition of 1005% ± 1% of the nominal positive force, the service life of the injection pump is not less than 150,000 times: 6 Test method 6.1 Test conditions 6.]. Test medium, using the "heart" ~ small \ giant base. [.2 Test environment fade: 15-40. ||tt| |6.3 Air test Swing the operating handle, the oil pump should comply with the provisions of 5.: 6.3 Pressure test Under the nominal pressure, swing the operating handle, the pump should comply with the provisions of 5.: 6.4 For the test Under the nominal pressure of about 1.25, k is small, the oil pump seat should comply with the provisions of 5.3, 6 Under the nominal pressure, measure the amount of white oil 19 working cycles, the oil room signal should comply with the period of 5. t||Take the sample from the single slide in the table, and press 2B[50CC3 to reach the inspection gold, and its cleaning degree meets the requirements of the product.10. 67 Life test monitoring It is carried out on a test bench that reports the working condition of the system under the condition of 100% of the nominal pressure. Its case count meets the requirements of 5.11. 7 Acceptance rules 1.1 The oil-rich pump must be carefully tested before delivery. The test tolerance should be in accordance with 6.1, 6.2, 5.3 and 3. regulations. JB/T9651.11997 .2 Each manual rescue lubricant can be shipped after passing the test in the manufacturer. 7.3 Type or test For new trial-produced products or discontinued production, if the lubrication system structure, materials and technology have changed, the type test should be carried out. The content of the type test includes: ) All contents of the factory test: b) Cleaning test: c) Life test. 8 Marking, packaging, transportation and storage , each product label should be clearly marked when appropriate, and its format and size are listed! 5133 regulations label content includes: ) Product model, name: 5) Ball pressure: C) Consumption points: d) Factory date: r) Factory jurisdiction: f) Production name, 8.2 For the same product to provide technical documents, the document should be in accordance with the provisions of JB/Z189, the documents include: 1) Product instruction sheet 5) Product certificate and packing list. 8.3 The exposed parts of the product should be anti-rust treated according to the provisions of 2BJ501 before packaging. 8.4 The packaging of the product shall comply with the specifications of 3B/T3207 and shall be suitable for land transportation and packaging requirements. There are no restrictions on materials for domestic sales. 8.5 The packaging and transportation marks shall comply with the relevant provisions of GB1S1. x. The product shall be stored in a well-ventilated and moisture-proof place. Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.