title>JB/T 1377.1-1999 SZ series micro DC servo motor - JB/T 1377.1-1999 - Chinese standardNet - bzxz.net
Home > JB > JB/T 1377.1-1999 SZ series micro DC servo motor
JB/T 1377.1-1999 SZ series micro DC servo motor

Basic Information

Standard ID: JB/T 1377.1-1999

Standard Name: SZ series micro DC servo motor

Chinese Name: SZ系列微型直流伺服电动机

Standard category:Machinery Industry Standard (JB)

state:in force

Date of Release1999-08-06

Date of Implementation:2000-01-01

standard classification number

Standard Classification Number:Electrical Engineering>>Rotary Motors>>K24 Micro Motor

associated standards

alternative situation:JB 1377-1974

Publication information

publishing house:Mechanical Industry Press

Publication date:2000-01-01

other information

drafter:Gao Shaoping, Lu Zhaotong

Drafting unit:Boshan Motor Factory, Tianjin Safety Motor Co., Ltd., Qinghai Micromotor Factory, Benxi Micromotor Factory, etc.

Focal point unit:National Micromotor Standardization Technical Committee

Proposing unit:National Micromotor Standardization Technical Committee

Publishing department:Ministry of Machinery and Electronics Industry

Introduction to standards:

This standard specifies the technical requirements, test methods, inspection rules, quality assurance period, marking, packaging, transportation and storage requirements of SZ series micro DC servo motors. This standard applies to SZ series micro DC servo motors (hereinafter referred to as motors). This series of motors are separately excited DC servo motors with commutators, which can be used as actuators in automatic control systems and can also be used as drive components. This series of motors are divided into two categories according to the operating environment conditions: ordinary type and humid tropical type (indoor). The humid tropical type motor has "TH" added after the ordinary type model. This series of motors is not suitable for environmental conditions with special requirements, such as: explosion-proof, oil-resistant, chemical corrosion-resistant, exposed to the sun, rain, etc. JB/T 1377.1-1999 SZ series micro DC servo motors JB/T1377.1-1999 Standard download decompression password: www.bzxz.net

Some standard content:

The standard of the People's Republic of China for the hydraulic press machinery industry JB/T1377.11999
1999-08-064
2000-01-01
JB/T1377.1±1999
This standard is a revision of JB1377-74 "SZ series micro DC servo motor". The relevant provisions in GB/T7345-1994 and GB/T14819-1993 were cited during the revision. This standard is consistent with the relevant standards and conforms to the provisions of GB/T1.1-1993 in terms of writing format: This standard will replace JB1377-74 from the date of implementation. This standard is proposed and managed by the National Micro Motor Standardization Technical Committee. The drafting units of this standard are: Boyu Motor Factory, Tianjin Safety Motor Co., Ltd., Qinghai Micro Motor Factory, Benxi Micro Motor Factory, Ningbo Kailis Electric Co., Ltd., Fujian Wanda Motor Co., Ltd. The main drafters of this standard are Gao Shaoping and Lu Zhaotong. The motor factory is entrusted with the interpretation of this standard. 1
G2 0P pEe/
JB/T1377.11999
This standard specifies the technical requirements, test methods, inspection rules, quality assurance period, marking, packaging, transportation and storage requirements of SZ series micro DC servo motors. This standard applies to SZ series micro DC servo motors (hereinafter referred to as motors). This series of motors are separately excited DC servo motors with commutators, which can be used as actuators in automatic control systems and can also be used as drive components. This series of motors are divided into two categories according to the use environment conditions: ordinary type and humid tropical type (indoor). The humid tropical type motor has "TH" added after the ordinary type model.
This series of motors is not suitable for environmental conditions with special requirements, such as: explosion-proof, oil-resistant, chemical erosion-resistant, exposed to the sun, rain, etc. Cited Standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When the standard is published, the versions shown are valid: All standards will be revised, and the parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T2423.3-1993 Basic environmental test procedures for electric and electronic products Test Ca: Steady-state damp heat test method GB/T2423.4-1993
Basic environmental test procedures for electric and electronic products Test Db: Alternating damp heat test method GB/T2423.16--1990 Basic environmental test procedures for electric and electronic products Test J: Mildew test method GB/T 7345-1994
Basic technical requirements for controlling micromotors
GB/T10069.1-1988 Noise determination method for rotating motors and engineering determination method for limit noise GB/T14819-1993
3 Technical requirements
3.1 Environmental conditions for use
General technical conditions for electromagnetic DC servo motors 3.1.1 The air pressure shall not be less than 61.7 kPa (4000m). 3.1.2 Ambient temperature: -40~+55℃
3.1.3 Relative humidity: 90%~95%. 3.1.4 Any installation position.
3.1.5 The humid tropical type motor is also allowed to work under the following conditions: a) Condensation;
b) Mold.
3.2 Working system
The motor is a continuous working system.
1999-08-06
2000-01-01
3.3 Circuit diagram
The circuit diagram is shown in Figure 1.
3.4 ​​Rated data
The rated data of the motor shall comply with the provisions of Table 1. Model
36SZ01
36SZ02
36SZ03
36SZ04
36SZ05
36SZ06
36SZ07
36SZ51
36SZ52
36SZ53
36SZ54
36SZ 55
36SZ56
36SZ57
45SZ01
45SZ02
45SZ03
45SZ04
45SZ05
JB/T1377.11999
Figure 1 Circuit diagram
Rated data
Allowable positive and negative reverse difference
45SZ06 | |tt | 5SZ58
55SZ01
5 5SZ02 | |tt | | 55SZ03 | Sz54
55SZ55
55 SZ56
55SZ57
55Sz58
70SZ01
70SZ02
70SZ03
70SZ04
70SZ05
JB/T1377.11999
Table 1 (continued)
Allowable positive and negative rotation difference
70SZ06| | tt | t||90SZ01
90SZ02| | tt |
110SZ52
110 SZ53
110SZ54
130SZ1Www.bzxZ.net
130SZ02
130SZ03
130SZ04
Rated data are checked in cold state,
JB/T1377.11999
Table 1 (end)
The motor output is based on torque,
Power is for reference only.
is ±12%; 55SZ~130SZ
3 Speed ​​tolerance: 36SZ~45SZ
Armature excitation
is ±10%
Allowable forward and reverse rotation difference
3.5 Structural type
3.5.1 The motor is a closed self-cooling type
JB/T1377.11999
3.5.2 The motor can be made into the installation structure type shown in Table 2. The shaft extension can be made into single shaft extension and double shaft extension. For double shaft extension motors, the commutator end shaft extension is not used to transmit rated torque. Table 2 Installation structure type
Installation structure type
Machine base outer circle installation
End cover flange installation
Foot installation
3.6 Appearance and installation dimensions
Installation structure type code
Single shaft extension
Double shaft extension
The appearance dimensions and installation dimensions of the motor shall comply with the provisions of Figures 2 to 9 and Tables 3 to 7. Note: The dimensions without tolerance in the figures are basic dimensions. h
Figure 2 Appearance and installation dimensions
Table 3 Appearance and installation dimensions
36SZ01-07
36SZ51~57
45SZ01-08
45SZ51~58
Machine frame size
36~130
36~130
90~130
365201-07
36SZ51-57
45SZ51-
JB/T1377.11999
Figure 3 Appearance and installation dimensions
Table 4 Appearance and installation dimensions
Figure 4 Appearance and installation dimensions
55SZ01-08
55SZ51-58
70SZ01~08
7OSZ51-58
908201 -04
90Sz51-64
110SZ01~04
110SZ51-5
JB/T1377.11999
Qiu 5 Appearance and installation dimensions
-0: 15
Figure 5 Appearance and installation dimensions
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.