Some standard content:
Carbon steel saddle ring packing
HG/T 21554.1--- 95
1 Subject content and scope of application
1.0.1 This standard specifies the materials, specifications, technical requirements, inspection rules, marking, packaging, transportation, storage and other requirements of 25*, 38*, 50#, 70* carbon steel saddle ring packing. The applicable temperature of carbon steel saddle ring packing is less than or equal to 350℃. 1.0.2
GB 710
GB1184
GB1804
Cited standards
《High-quality carbon structural steel sheets and strips》《Provisions for shape and position tolerances without tolerances》《Limit deviations of dimensions without tolerances for tolerances and fits》《Dimensions, shape, weight and allowable deviations of cold-rolled steel sheets and strips》3 Marking, specifications and characteristics
3.1 Marking
X XRSCSX X
Nominal size
Carbon steel rectangular saddle ring
Standard number
3.2 Specifications and characteristics
3.2.1 The metal rectangular saddle ring filler has a ring-shaped saddle structure composed of a ring and a saddle, with a tongue-shaped rib inside, as shown in Figure 3.2:1.
Carbon steel saddle ring packing
In the figure: the unit of size is mm; D
Inner arc spacing; Dz-
Bi width; a wall thickness.
Outer arc spacing; H--height;
3.2.2 The commonly used saddle ring packing sizes in industry are 25#, 38#, 50# and 70#. 3. 2. 3
The specifications and dimensions of carbon steel saddle ring packing are shown in Table 3.2.3. Table 3.2.3 Specifications and dimensions of carbon steel saddle ring packing Inner arc spacing
Outer arc spacing
76.5±1.2
16.5±0.84
35.5±1.0
The characteristic parameters of carbon steel saddle ring packing are shown in Table 3.2.4. Table 3.2.4
Packing size
70*70×35.5×1.0
50×29×0.8www.bzxz.net
38*38×16.5×0.6
25×15×0.5
Number of stacking
(m-°)
28.5±0.84
42.2±1.0
52.1±1.0
Carbon steel saddle ring packing Geometric characteristic parameters
Bulk density
(kg/m)
Specific surface area
(m°/m')
Porosity
(m°/m°)
0.5±0.05
0.6±0.07
0.8±0.07
Dry filling factor
4.0.1 The selected carbon steel material shall be in accordance with the technical conditions of cold-rolled steel plates specified in GB710. 4.0.2 The dimensions, shape, weight and allowable deviation of the selected cold-rolled steel plates and steel strips shall be in accordance with the B-level precision specified in GB708.
4.0.3 The selected materials shall have quality inspection certificates, certificates of conformity, and test reports, and shall be sampled and inspected regularly. Materials without the above certificates shall be subject to quality analysis and inspection. 41
5 Manufacturing requirements
5.0.1 The rectangular saddle ring packing is composed of two sections of curves, the upper arc is a circular curve, and the lower arc is a semicircular curve. For specific structural dimensions, see Figure 5.0.1 and Table 5.0.1.
Figure 5.0.1 Carbon steel rectangular saddle ring packing structural dimensions: The unit of dimension is mm, and the unit of angle is degree. A, B, C, E, F, G, L plate specifications before processing; Di - inner arc spacing, Dz - outer arc spacing H - outer arc height; K - flange height; R - inner arc radius, R.R2 - degree.
Bending radius angle
Carbon steel rectangular saddle ring packing structural dimensions
5.0.2 The stamping processing accuracy shall be in accordance with the IT15 level accuracy in GB1804 standard and the B level accuracy in GB1184 standard.
The surface of the finished rectangular saddle ring packing should be smooth, free of rust marks, cracks, and burrs on the edges. 5.0.3
Inspection and acceptance
Acceptance rules
6.1.1 The packing should be accepted in batches. One size of packing can be regarded as a batch. The batch quantity is shown in Table 6.1.1. When the production volume of one size of packing is less than the batch value specified in Table 6.1.1, it can be regarded as a batch according to the production volume of one size.
Table 6.1.1 Packing batches
Packing type
38#70#
The number of samples sampled for inspection in each batch of packing shall not be less than 60. 6.1.3 If more than 5% of the number of samples of the appearance dimensions do not meet the requirements of this standard, the number of samples should be doubled from the same batch of products and retested. The results of the repeated tests also apply to the batch of products. If the unqualified rate of the retested samples is still greater than 5% of the sampling volume, the batch of products is unqualified. 6.2 Inspection method
6.2.1 The inner arc spacing, outer arc spacing, width, height and wall thickness of the packing are measured with a vernier caliper. Each test item of each sample shall not be less than 2 test points. The measurement value requirements are in accordance with Table 3.2.3.6.2.2 When the shape and size of the packing change, the packing characteristics, fluid mechanics and mass transfer performance tests are required. 44
Marking, packaging and storage and transportation
7.1 Marking
7.1.1 The packing box should have a product certificate. The certificate should indicate the product name, specification size, inspection result, inspection date, production date, manufacturer name, and be stamped with the quality inspection seal and inspector seal. 7.1.2 The outer packaging of the product should indicate the product name, specification, packing quality (or quantity), manufacturer, and indicate moisture-proof, anti-heavy pressure and other marks.
7.2 Packaging
The packaging should be made of dry boxes or other materials, lined with moisture-proof materials. 7.2.11
The packaging box must be strong enough to ensure it is intact during handling and loading and unloading. 7.2.2
7.3 Transportation and storage
7.3.1 The product must be protected from moisture and rain during transportation. 7.3.2 The product should be kept dry and corrosion-free during storage, and the inner packaging should be kept intact. 45
Month Proposing unit, chief editor unit
Additional instructions
And main drafters
Chemical Engineering Design Technology Center Station, Ministry of Chemical Industry Proposing unit: ,
Chemical Engineering Design Technology Center Station, Ministry of Chemical Industry Editor-in-chief: Yu Hongshou Lin Jie
Reviewer: Xiao Chengji Tan Shen
Li Chunfang
Fei Weiyang
Approving person: Wang Fuhua
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.