QB/T 2736-2005 Automatic rinsing, filling and sealing machine for bottled water beverages
Some standard content:
1CS 67.260
Classification number: X99
Award number: 164162005
Light Industry Standard of the People's Republic of China
QB/T 2736-2005
Automatic rinsing, filling and capping machine for bottled water-drinks2005-07-26Issued
National Development and Reform Commission of the People's Republic of China2006-01-01Implementation
This standard is codified by China Light Industry Federation. Foreword
This standard is codified by National Technical Committee for Standardization of Light Industry Machinery and Technical Committee for Wine and Beverage Machinery! QR/T2736-2005
This standard is drafted by Guangzhou Dadianlong Packaging Machinery Co., Ltd., Peifangshan Packaging Machinery Co., Ltd., Zhangjiagang Fangyinli Machinery Co., Ltd., etc., and the main drafters are: Yao Weiguo, Ling Luhua, Zhang Lingming, Gao Mingge, Zhang Jun, Wang Yunchun, Yuan Zhonghua, this standard is released for the first time
1 Scope
Bottled water beverage fully automatic rinsing, filling and sealing machine QB/T2736—2005
This standard specifies the definition, requirements, test methods, inspection rules and signs, packaging, transportation and treatment of bottled water beverages.
The standard is not applicable to polycarbonate (PC) sample drinking water full-automatic flushing machine (hereinafter referred to as "product". This standard is applicable to water with a capacity of 60 tons/h~1000 tons/h, a filling capacity of 101.--20T, and materials such as pure floating system, chemical water, natural purified water, etc. (hereinafter referred to as "finished water"). 2 Normative referenced documents
The following documents are used as references to this standard and become the provisions of this standard. For any document with a specified date, all subsequent amendments (including errata) or static versions are not applicable to this standard. However, the parties who reach an agreement based on this standard are encouraged to use the latest versions of these normative documents. For any undated referenced documents, the latest version shall apply to the standard. CB/3766 General technical requirements for liquid systems
GBT3768-19 Method for determining noise level by internal pressure method
GB/T7932
GB/13306 Labels
GB133B4 General technical requirements for electromechanical products packaging GB/T14253 General technical requirements for light industrial machinery GB16798 Safety and sanitation of food machinery
QB/T2467 Non-toxic equipment for industrial use
3 Definitions
This standard adopts the following definitions:
Flushing
The cleaning liquid (water) with a constant force, disinfectant (medicine), and finished product water are rinsed into the barrel body and outer surface for several times. 3.2
Filling
Do not fill the barrel by mechanical means. 3.3
Capping
Use a seat plate or roller chain (wheel, belt) with a fixed force to seal the barrel. 4 Requirements
4.1 Working conditions
4.1.1 The diameter and height of the barrel cover should be consistent with the diameter and height of the barrel mouth. 41.2 Type requirements of the cover, the roundness of the square diameter is not more than 5mm. 4.1.3 The height difference of the screen is not more than 2mmQR/T 27362C05
4.1.4 The barrel should be equipped with a guide part.
4.1.5 The compressed gas used for the product should be clean air: T working pressure 0.5MT0.8MPa4.1.6 The auxiliary control equipment for the flushing pipeline of the finished product water should be divided and set.4.1.7 The actual temperature UC--30T
4.1.8 The pressure parts of the product should be in accordance with the instructions for use and maintenance:4.1.9 The transmission parts should be lubricated within 36h, lubricated and disinfected within 72h110 The safety facilities are limited to 24h
4.1.1 The maintenance period of the product is 4h·5h4.2 Basic requirements
12.1 Product! 4.2.2 The product shall use the stainless steel pipe or the relevant requirements of Q/12467. 4.2.3 The product certification, mechanical engineering, installation and quality assurance shall meet the requirements of 14253. 4.2.4 The production system shall be fully inspected according to the requirements of B1678. 4.2.5 The production system characteristics and the requirements of the production system shall meet the requirements of 032. 4.2.6 The installation characteristics of the product fluid bed system shall comply with the requirements of GH/7. 4.2.7 The pipelines that are not in accordance with the product specifications shall be made of materials that can be selected and installed with 1CT18N9, 0Cr1&N9.Cr1UNi10,0C17N12Mu2 or 00CT17Ni11Mo2.4.3 Requirements for idling test Before the whole machine is put into production, the unit shall conduct a running test and meet the following requirements: a) The product is running smoothly, on time, the transmission is working steadily, the gas is small, and the concentration ratio is reliable: the light factory is running normally: c) The signal indication display is normal: d) The safety and continuous reading can be installed with safety sound. 4.4 Performance in use 4.4.1 The production capacity of the product under the condition of running normally is not less than the nominal production capacity. 44.2 For the above mentioned, the rate of use of natural liquid (with two-wheel drive, mechanical water) disinfection (hot water limit is not more than 2% of the busy tank volume per hour. 4.4.4 Washing liquid), disinfectant, or product water to rinse 100% of the area. 4.4.5 After the completion of the water rinse, confirm the indicators of the natural environment in the body: the bottom temperature index, the pollution protection index, the type of object index, etc. The requirements should be consistent with the water.
4.4.6 Automatic liquid back-up after charging, one rate is not less than 1:4.4.7 Liquid loss rate is not less than 43 (excluding the first request: 4.43 General assembly accuracy qualified rate is less than R.5%. Micro-installation, phosphorus, etc.) Minimum loading capacity 9:
6) Maximum loading capacity of the filling car is 103:11.9 When the mouth (cover) contains no less than 9%: 1, the qualified product should meet the regulations) Tuoyi Village has obvious surplus on the barrel body: 5) Report the appearance of the barrel without a period of urgent rental; Ken cover port position factory: upper Rui and seat ring connection, that is, understand the cover intention:,
4.4.10 Finished product individual rate is not less than 97,
14! Touch the special flat intention, dynamic south, Yang Chang Xiao spray. 2 production method its production is not right people: BA
QB/72/36—2UU5
4.4.13 flushing, 2 sources of pipes and water tanks should not be painted, leaking, pipe excitation and wide industry seal to, oil mixing, 4.14 each action level, phase without order, light can be beautiful, power meter, gas therapy, gas up and other actions should be sensitive to the page called month! Work procedures are all caused by:
L.5 performance with standard
three selected changes to the design of the technology and the need to stop the belt quickly! a) The product life is not less than 15000h: b) The service life of the equipment is not less than 3uwh. 5 Test methods 5.1 Empty running test After continuous flow of 1h under the nominal load (flushing standard water requirements, filling water can be used in summer), the test is effective in winter and winter, and the efficiency should be in accordance with 4.3. 5.2 Monthly test 5.2.1 The internal flushing rate should meet the requirements of 4.4.4. 5.2.2 The product running speed should meet the requirements of 4.4.11 and 4.4.1. 5.2.3 The washing, rinsing and water tank of the equipment should meet the requirements of 4.1.13. 5.3 Determination of production capacity
In the case of light annual production capacity of the company, 3 water is used as the medium for the machine test, and the number of barrels of products in the pen is 1: ... The remaining time of the barrel and the barrel rate (driven by the upper capture agent) 13
nominal cattle capacity one operation, the sample string certificate number is full table will avoid the stop: when the test is carried out at the production site, the fee is required in the public, and the operation can be carried out under: the test time 2m. The formula (2) calculates the white action 1. Wei pays the editor and the card rate. T10
—one three actions and two eliminations are confirmed, the barrel plate:
one self-effective time is full, the afraid of the effective payment of the price calculation, the single signature, the total teaching reported by the action (certificate unqualified agent indication calculation: the change loss 5.5. Determination of the loss rate of cleaning liquid (brick water) and disinfectant (medicine) 2. The main energy of the public can be operated under the knife, and the washing liquid (city technique) and disinfectant (system) are tested respectively: according to the test time 20, the formula, external calculation, etc. are used to determine the loss rate of disinfectant (medicine). Yx100
一范洗波(柜水、消出凝:双损展率,%:5.
一消流滤!板水,消酒热代快书型,單位升 liter(3)
QB/T2736—2005
洁净洗渡(实践六,消李没(龄水)箱体积秘,單位元(1.)5.B 后的製品水后洗身內 ... 1.-x100
, one - the automatic barrel squeezing ratio of the flushing point, the rate of overturning and jamming, about; the number of barrels that fall down after flushing (barrels that fail to meet the standards are not counted), the unit is barrel: 521 The total number of barrels that fall down in the flushing hall (barrels that fail to meet the standards are not counted), the unit is barrel. 5.8 Determination of the loss rate of the filter body
When operating at nominal production capacity, with water as the medium: When the production site is tested, it is required to operate at nominal production capacity, with beach loading materials as the allowance, the number of selected products is 5 times the standard number of heads, and the weight of each selected product minus the homogeneity rate of the packaging material is the net annual liquid material, and the concentrated loading loss is calculated according to the winter formula (5): T-ra. x 0
or:
drop loss rate of the loading,:
barrel flow is solidified, cut off the net content of the loading material, the total is 1000 points (): one bar flow after loading, the total amount of loading material, the unit is "gram (k). 5.9 Determination of the qualified rate of concentrated loading
operate at the nominal production capacity, take water as the medium, the number of samples is 10 times the number of loading heads: the test is carried out in a small production site, it is required to operate at the nominal production capacity, take the loading material as the medium, and the test interval is 20min. According to formula (6) and formula (7), prepare one plug of the minimum and maximum cold room volume standard sample respectively, and determine the net content by weighing, the mass of the measured standard sample minus the mass of the packaging material used is the net content of the leakage material, the net weight of the material divided by the cubic average density of the material is the content marked with volume root.
raie=Y ×98%
=Y,×103%
or:
the minimum amount of standard filling liquid is the total amount, unit is liter (:Y
the net content of swimming pool parts, unit is liter (L) the chemical content of sealed liquid, unit is liter (L). (6
deep comparison: compare the samples with the standard samples, and those that meet the requirements of 4.4.8 are qualified products. If there is a dispute over the unqualified products, use the weighing method to judge: calculate the qualified rate of filling accuracy according to the formula (). ex100
where:
F.-fine filling is now standard, %:
a careful concentration table 5.10 Determination of qualified sealing rate QB/T2738-2G05 Under the nominal production capacity, with technology as the medium, the number of sample barrels is the number of heads: When conducting the test at the production site, it is required to be within the nominal production capacity, with the material loaded in port as the medium, the inspection time is 20mn, and it meets the requirements of 4.4.9. 1 qualified product, according to the formula: - qualified rate: - qualified number of sample barrels, the unit is Tnx; 1uo
Total number of seals (damaged due to poor quality of the two), the unit is 5.11 Determination of qualified rate of finished products
pieces. Nominal cattle production "operation, with water as the price, the number of sample barrels is 1 times the number of port heads: when the inspection is carried out at the cattle production site: it is required to operate under the public production capacity, with port loading materials as the medium, and the test is called 20mln: the products that meet the requirements of 4.4.8 are qualified products, and those that meet the requirements of 4.4.7 are qualified products. The qualified rate of finished products is calculated according to formula (0). ×100
Wherein;
When the qualified rate of finished products, %:
--Number of qualified products, unit is: total number of barrels (excluding the loss due to poor quality of the cover itself), standard position is accurate, F
5.12 Noise measurement
When the product is in operation, the sound level meter specified in GR/T3768-1996 is used to measure the relative noise of the product in air conditioner operation. The measuring disk table selects the corresponding half of each plane with the reference body, and the measurement distance is strictly controlled by the sound transmission machine GB/13 763-1996 two records C in Figure C4, but the product is not tested in advance 6 inspection rules
6.1 Inspection classification
Product inspection classification Factory inspection and type inspection: 6.2 Factory inspection
6.2.1 Inspection items
Under the working conditions of 4.1.1--4.1.8, the inspection plan is not a standard requirement 4.4.1.4.4.2.4.4.4,4.4.6~4.4.146.2.2 Judgment rules
After the product is manufactured and tested, the quality inspection department shall conduct inspection and supervision, and the store can only issue the product after the qualified inspection. When the product is issued, the product certificate shall be issued. If the number of inspections exceeds 6, the new company shall issue the product again. If there are any non-conformities in the inspection, the product can be corrected and re-processed. If the product still does not conform to the standard after the product is re-processed, the product will be deemed non-conformity. 6.3 Type inspection
6. 3.1 Inspection conditions
When one of the following conditions occurs, the type inspection should be carried out: a) When the production of new products is conducted:
QB/T2736—2005
b) After formal production, the structure, materials, and process are greatly changed, which may affect the product performance: c) When the product is resumed after two years of suspension: d) When the inspection results are significantly different from the type inspection results: When the national regulatory agency proposes to conduct type inspection. The type inspection is carried out in the user's production. 6. 3. 2 Inspection items
When the working conditions meet 41, the inspection items are all or part of the technical requirements of this standard except 4. and are carried out one by one. 8.3.3 Sampling
The samples for type control inspection shall be taken from the output that has passed the factory inspection. The samples can be randomly sampled before the next period of time. When the annual output is less than or equal to 20 units, 1 unit shall be sampled from any batch: b) When the output is 21-50 units, 2 units shall be sampled from any batch: a) When the annual output is 51-60 units, 3 units shall be sampled from the batch. 6.3.4 Judgment rules
The product is qualified if all items of type inspection are qualified. If there are unqualified items, they shall be re-inspected. If the unqualified items are unqualified, the batch of products shall be judged to be unqualified for dosage form inspection.
Marking, packaging, transportation and storage
7.1 Marking
7.1.1 Each product shall be labeled in a conspicuous position, and the label shall comply with the relevant provisions of GB/T13306. 7.1.2 The label content should include:
product model and product name;
b) name of the manufacturer;
core product technical parameters:
d) appearance size:
f) product number:
date of manufacture;
7.2 Packaging
7.2.1 Product packaging should comply with the relevant provisions of GB/T13384. 7.2.2 Each time the product is produced, the following technical support certificates should be brought along at random:
b) product promotion manual and accompanying booklet;
installation and use instructions;
spare parts list.
7.9 Transportation
Whether the product is transported in whole package or in individual packages, the following provisions must be met before transportation: a) Land transportation should meet the requirements of land transportation; b) Road transportation should meet the requirements of water transportation; c) Transfer and unloading should be smooth and free of violent impact. 7.4 Purchase and storage
The product should be stored in a well-ventilated, dry, rainproof and non-corrosive indoor environment. After storage for more than 1 month, the box should be inspected and the anti-rust coating and packaging should be newly applied if necessary.B. Inspection of various indicators of residual filter in the finished water after flushing. Inspection method of finished water.
5. Determination of the rate of overturning and jamming of barrels when the barrels are automatically dropped after flushing. The nominal production capacity is lower than 10. When testing in a small production plant, it is required to operate under the nominal production capacity. The test period is 20 minutes. According to formula (4), the automatic barrel drop rate and jamming rate are calculated. 1.-x100
, the automatic barrel drop rate and jamming rate of the flushing point, about; the number of barrels that are overturned and dropped when the barrels are automatically dropped after flushing (barrels that are unqualified are not counted), the unit is barrels: 521 The total number of automatic barrels dropped in the flushing hall (unqualified ones are not counted), the unit is. 5.8 Determination of filter loss rate during fillingbZxz.net
When operating at nominal production capacity, take water as medium: When the production site is tested, it is required to operate at nominal production capacity, take beach load materials as allowance, the number of selected products is 5 times the standard number of heads, and use the weighing shear method to measure the mass of each selected product minus the homogeneity rate of the packaging material, which is the net annual loss of the standard liquid material. Calculate the concentrated silver loss according to the winter formula (5): T-ra. x 0
or:
drop loss rate of the loading,:
barrel flow is solidified, cut off the net content of the loading material, the total is one thousand points (): one bar number after loading, the total original basis of the old loading material, the unit is "gram (k). 5.9 Determination of the qualified rate of concentrated loading
operate at the nominal production capacity, use water as the medium, and the number of samples is 10 times the number of loading heads: conduct the test in a small production site, require the operation at the nominal production capacity, use the loading material as the medium, and the test interval is 20min. According to formula (6) and formula (7), prepare one plug of the minimum and maximum cold room volume standard sample respectively, and determine the net content by weighing. The mass of the measured standard sample minus the mass of the packaging material used is the net content of the leaked material, and the net weight of the material divided by the cubic average density of the material is the content marked with the volume root.
raie=Y ×98%
=Y,×103%
or:
the minimum amount of standard filling liquid is the total amount, unit is liter (:Y
the net content of swimming pool parts, unit is liter (L) the chemical content of sealed liquid, unit is liter (L). (6
deep comparison: compare the samples with the standard samples, and those that meet the requirements of 4.4.8 are qualified products. If there is a dispute over the unqualified products, use the weighing method to judge: calculate the qualified rate of filling accuracy according to the formula (). ex100
where:
F.-fine filling is now standard, %:
a careful concentration table 5.10 Determination of qualified sealing rate QB/T2738-2G05 Under the nominal production capacity, with technology as the medium, the number of sample barrels is the number of heads: When conducting the test at the production site, it is required to be within the nominal production capacity, with the material loaded in port as the medium, the inspection time is 20mn, and it meets the requirements of 4.4.9. 1 qualified product, according to the formula: - qualified rate: - qualified number of sample barrels, the unit is Tnx; 1uo
Total number of seals (damaged due to poor quality of the two), the unit is 5.11 Determination of qualified rate of finished products
pieces. Nominal cattle production "operation, with water as the price, the number of sample barrels is 1 times the number of port heads: when the inspection is carried out at the cattle production site: it is required to operate under the public production capacity, with port loading materials as the medium, and the test is called 20mln: the products that meet the requirements of 4.4.8 are qualified products, and those that meet the requirements of 4.4.7 are qualified products. The qualified rate of finished products is calculated according to formula (0). ×100
Wherein;
When the qualified rate of finished products, %:
--Number of qualified products, unit is: total number of barrels (excluding the loss due to poor quality of the cover itself), standard position is accurate, F
5.12 Noise measurement
When the product is in operation, the sound level meter specified in GR/T3768-1996 is used to measure the relative noise of the product in air conditioner operation. The measuring disk table selects the corresponding half of each plane with the reference body, and the measurement distance is strictly controlled by the sound transmission machine GB/13 763-1996 two records C in Figure C4, but the product is not tested in advance 6 inspection rules
6.1 Inspection classification
Product inspection classification Factory inspection and type inspection: 6.2 Factory inspection
6.2.1 Inspection items
Under the working conditions of 4.1.1--4.1.8, the inspection plan is not a standard requirement 4.4.1.4.4.2.4.4.4,4.4.6~4.4.146.2.2 Judgment rules
After the product is manufactured and tested, the quality inspection department shall conduct inspection and supervision, and the store can only issue the product after the qualified inspection. When the product is issued, the product certificate shall be issued. If the number of inspections exceeds 6, the new company shall issue the product again. If there are any non-conformities in the inspection, the product can be corrected and re-processed. If the product still does not conform to the standard after the product is re-processed, the product will be deemed non-conformity. 6.3 Type inspection
6. 3.1 Inspection conditions
When one of the following conditions occurs, the type inspection should be carried out: a) When the production of new products is conducted:
QB/T2736—2005
b) After formal production, the structure, materials, and process are greatly changed, which may affect the product performance: c) When the product is resumed after two years of suspension: d) When the inspection results are significantly different from the type inspection results: When the national regulatory agency proposes to conduct type inspection. The type inspection is carried out in the user's production. 6. 3. 2 Inspection items
When the working conditions meet 41, the inspection items are all or part of the technical requirements of this standard except 4. and are carried out one by one. 8.3.3 Sampling
The samples for type control inspection shall be taken from the output that has passed the factory inspection. The samples can be randomly sampled before the next period of time. When the annual output is less than or equal to 20 units, 1 unit shall be sampled from any batch: b) When the output is 21-50 units, 2 units shall be sampled from any batch: a) When the annual output is 51-60 units, 3 units shall be sampled from the batch. 6.3.4 Judgment rules
The product is qualified if all items of type inspection are qualified. If there are unqualified items, they shall be re-inspected. If the unqualified items are unqualified, the batch of products shall be judged to be unqualified for dosage form inspection.
Marking, packaging, transportation and storage
7.1 Marking
7.1.1 Each product shall be labeled in a conspicuous position, and the label shall comply with the relevant provisions of GB/T13306. 7.1.2 The label content should include:
product model and product name;
b) name of the manufacturer;
core product technical parameters:
d) appearance size:
f) product number:
date of manufacture;
7.2 Packaging
7.2.1 Product packaging should comply with the relevant provisions of GB/T13384. 7.2.2 Each time the product is produced, the following technical support certificates should be brought along at random:
b) product promotion manual and accompanying booklet;
installation and use instructions;
spare parts list.
7.9 Transportation
Whether the product is transported in whole package or in individual packages, the following provisions must be met before transportation: a) Land transportation should meet the requirements of land transportation; b) Road transportation should meet the requirements of water transportation; c) Transfer and unloading should be smooth and free of violent impact. 7.4 Purchase and storage
The product should be stored in a well-ventilated, dry, rainproof and non-corrosive indoor environment. After storage for more than 1 month, the box should be inspected and the anti-rust coating and packaging should be newly applied if necessary.B. Inspection of various indicators of residual filter in the finished water after flushing. Inspection method of finished water.
5. Determination of the rate of overturning and jamming of barrels when the barrels are automatically dropped after flushing. The nominal production capacity is lower than 10. When testing in a small production plant, it is required to operate under the nominal production capacity. The test period is 20 minutes. According to formula (4), the automatic barrel drop rate and jamming rate are calculated. 1.-x100
, the automatic barrel drop rate and jamming rate of the flushing point, about; the number of barrels that are overturned and dropped when the barrels are automatically dropped after flushing (barrels that are unqualified are not counted), the unit is barrels: 521 The total number of automatic barrels dropped in the flushing hall (unqualified ones are not counted), the unit is. 5.8 Determination of filter loss rate during filling
When operating at nominal production capacity, take water as medium: When the production site is tested, it is required to operate at nominal production capacity, take beach load materials as allowance, the number of selected products is 5 times the standard number of heads, and use the weighing shear method to measure the mass of each selected product minus the homogeneity rate of the packaging material, which is the net annual loss of the standard liquid material. Calculate the concentrated silver loss according to the winter formula (5): T-ra. x 0
or:
drop loss rate of the loading,:
barrel flow is solidified, cut off the net content of the loading material, the total is one thousand points (): one bar number after loading, the total original basis of the old loading material, the unit is "gram (k). 5.9 Determination of the qualified rate of concentrated loading
operate at the nominal production capacity, use water as the medium, and the number of samples is 10 times the number of loading heads: conduct the test in a small production site, require the operation at the nominal production capacity, use the loading material as the medium, and the test interval is 20min. According to formula (6) and formula (7), prepare one plug of the minimum and maximum cold room volume standard sample respectively, and determine the net content by weighing. The mass of the measured standard sample minus the mass of the packaging material used is the net content of the leaked material, and the net weight of the material divided by the cubic average density of the material is the content marked with the volume root.
raie=Y ×98%
=Y,×103%
or:
the minimum amount of standard filling liquid is the total amount, unit is liter (:Y
the net content of swimming pool parts, unit is liter (L) the chemical content of sealed liquid, unit is liter (L). (6
deep comparison: compare the samples with the standard samples, and those that meet the requirements of 4.4.8 are qualified products. If there is a dispute over the unqualified products, use the weighing method to judge: calculate the qualified rate of filling accuracy according to the formula (). ex100
where:
F.-fine filling is now standard, %:
a careful concentration table 5.10 Determination of qualified sealing rate QB/T2738-2G05 Under the nominal production capacity, with technology as the medium, the number of sample barrels is the number of heads: When conducting the test at the production site, it is required to be within the nominal production capacity, with the material loaded in port as the medium, the inspection time is 20mn, and it meets the requirements of 4.4.9. 1 qualified product, according to the formula: - qualified rate: - qualified number of sample barrels, the unit is Tnx; 1uo
Total number of seals (damaged due to poor quality of the two), the unit is 5.11 Determination of qualified rate of finished products
pieces. Nominal cattle production "operation, with water as the price, the number of sample barrels is 1 times the number of port heads: when the inspection is carried out at the cattle production site: it is required to operate under the public production capacity, with port loading materials as the medium, and the test is called 20mln: the products that meet the requirements of 4.4.8 are qualified products, and those that meet the requirements of 4.4.7 are qualified products. The qualified rate of finished products is calculated according to formula (0). ×100
Wherein;
When the qualified rate of finished products, %:
--Number of qualified products, unit is: total number of barrels (excluding the loss due to poor quality of the cover itself), standard position is accurate, F
5.12 Noise measurement
When the product is in operation, the sound level meter specified in GR/T3768-1996 is used to measure the relative noise of the product in air conditioner operation. The measuring disk table selects the corresponding half of each plane with the reference body, and the measurement distance is strictly controlled by the sound transmission machine GB/13 763-1996 two records C in Figure C4, but the product is not tested in advance 6 inspection rules
6.1 Inspection classification
Product inspection classification Factory inspection and type inspection: 6.2 Factory inspection
6.2.1 Inspection items
Under the working conditions of 4.1.1--4.1.8, the inspection plan is not a standard requirement 4.4.1.4.4.2.4.4.4,4.4.6~4.4.146.2.2 Judgment rules
After the product is manufactured and tested, the quality inspection department shall conduct inspection and supervision, and the store can only issue the product after the qualified inspection. When the product is issued, the product certificate shall be issued. If the number of inspections exceeds 6, the new company shall issue the product again. If there are any non-conformities in the inspection, the product can be corrected and re-processed. If the product still does not conform to the standard after the product is re-processed, the product will be deemed non-conformity. 6.3 Type inspection
6. 3.1 Inspection conditions
When one of the following conditions occurs, the type inspection should be carried out: a) When the production of new products is conducted:
QB/T2736—2005
b) After formal production, the structure, materials, and process are greatly changed, which may affect the product performance: c) When the product is resumed after two years of suspension: d) When the inspection results are significantly different from the type inspection results: When the national regulatory agency proposes to conduct type inspection. The type inspection is carried out in the user's production. 6. 3. 2 Inspection items
When the working conditions meet 41, the inspection items are all or part of the technical requirements of this standard except 4. and are carried out one by one. 8.3.3 Sampling
The samples for type control inspection shall be taken from the output that has passed the factory inspection. The samples can be randomly sampled before the next period of time. When the annual output is less than or equal to 20 units, 1 unit shall be sampled from any batch: b) When the output is 21-50 units, 2 units shall be sampled from any batch: a) When the annual output is 51-60 units, 3 units shall be sampled from the batch. 6.3.4 Judgment rules
The product is qualified if all items of type inspection are qualified. If there are unqualified items, they shall be re-inspected. If the unqualified items are unqualified, the batch of products shall be judged to be unqualified for dosage form inspection.
Marking, packaging, transportation and storage
7.1 Marking
7.1.1 Each product shall be labeled in a conspicuous position, and the label shall comply with the relevant provisions of GB/T13306. 7.1.2 The label content should include:
product model and product name;
b) name of the manufacturer;
core product technical parameters:
d) appearance size:
f) product number:
date of manufacture;
7.2 Packaging
7.2.1 Product packaging should comply with the relevant provisions of GB/T13384. 7.2.2 Each time the product is produced, the following technical support certificates should be brought along at random:
b) product promotion manual and accompanying booklet;
installation and use instructions;
spare parts list.
7.9 Transportation
Whether the product is transported in whole package or in individual packages, the following provisions must be met before transportation: a) Land transportation should meet the requirements of land transportation; b) Road transportation should meet the requirements of water transportation; c) Transfer and unloading should be smooth and free of violent impact. 7.4 Purchase and storage
The product should be stored in a well-ventilated, dry, rainproof and non-corrosive indoor environment. After storage for more than 1 month, the box should be inspected and the anti-rust coating and packaging should be newly applied if necessary.x 0
or:
drop loss rate of the loading,:
barrel flow is solidified, cut off the net content of the loading material, the total is 1000 points (): one bar flow after loading, the total amount of loading material, the unit is "gram (k). 5.9 Determination of the qualified rate of concentrated loading
operate at the nominal production capacity, take water as the medium, the number of samples is 10 times the number of loading heads: the test is carried out in a small production site, it is required to operate at the nominal production capacity, take the loading material as the medium, and the test interval is 20min. According to formula (6) and formula (7), prepare one plug of the minimum and maximum cold room volume standard sample respectively, and determine the net content by weighing, the mass of the measured standard sample minus the mass of the packaging material used is the net content of the leakage material, the net weight of the material divided by the cubic average density of the material is the content marked with volume root.
raie=Y ×98%
=Y,×103%
or:
the minimum amount of standard filling liquid is the total amount, unit is liter (:Y
the net content of swimming pool parts, unit is liter (L) the chemical content of sealed liquid, unit is liter (L). (6
deep comparison: compare the samples with the standard samples, and those that meet the requirements of 4.4.8 are qualified products. If there is a dispute over the unqualified products, use the weighing method to judge: calculate the qualified rate of filling accuracy according to the formula (). ex100
where:
F.-fine filling is now standard, %:
a careful concentration table 5.10 Determination of qualified sealing rate QB/T2738-2G05 Under the nominal production capacity, with technology as the medium, the number of sample barrels is the number of heads: When conducting the test at the production site, it is required to be within the nominal production capacity, with the material loaded in port as the medium, the inspection time is 20mn, and it meets the requirements of 4.4.9. 1 qualified product, according to the formula: - qualified rate: - qualified number of sample barrels, the unit is Tnx; 1uo
A total of 1 (due to poor quality of the two parts and the loss of the ring), the unit is plug 5.11 Determination of the qualified rate of finished products
pieces. The nominal cattle production is operated at the nominal power, with water as the price, and the number of sample barrels is 1 times the number of port heads: when the cattle production site is inspected: it is required to operate under the public production capacity, with port loading materials as the medium, and the test is called 20mln: simplified 4.4.8 requirements The qualified products of the leakage condition are counted as qualified products, and the qualified products that meet the requirements of 4.4. are counted as qualified products. The qualified rate of finished products is calculated according to formula (0). ×100
In the formula;
When the qualified rate of finished products, %:
Wei-out-loading and ≠ about the number of qualified products, the unit is capture: the total number of barrels (due to the poor quality of the phase and the cover itself, the loss is not counted), the typical position is accurate, F
5.12 Noise measurement
The product is in operation under the upper and lower belts. The sound level meter specified in GR/T3768-1996 is used to measure the product's air-conditioning operating noise. The measuring dial is selected from the corresponding half of the standard and the reference body. The measurement distance is strictly recorded in Figure C4 of the sound transmission machine GB/13763-1996. However, the product is not tested in advance. 6 Inspection rules
6.1 Inspection classification
Product inspection classification Factory inspection and type inspection: 6.2 Factory inspection
6.2.1 Inspection items
Meet 4.1.1--4.1.8. Under the operating conditions, the inspection items are not standard requirements of 4.4.1.4.4.2.4.4.4, 4.4.6~4.4.146.2.2 Judgment rules
After the product is manufactured and tested to have a certain operating condition, it shall be inspected! The quality inspection department shall conduct inspection and supervision, and the product can only be issued after the product passes the inspection. When the product passes the inspection, a certificate of conformity shall be issued. If the product passes the inspection for more than 6 years, the new product shall be issued again. If there are any non-conforming items during the inspection, the product can be adjusted. If the product still does not meet the requirements after the inspection, the product shall be deemed non-conforming. 6.3 Type inspection
6. 3.1 Inspection conditions
When one of the following conditions occurs, the type inspection shall be carried out: a) When the production of new products is carried out:
QB/T2736—2005
b) After formal production, the structure, materials, and process have changed significantly, which may affect the product performance: c) When the product is resumed after being discontinued for two years: d) When the inspection results are in good agreement with the type inspection results: When the national supervision agency proposes the requirement for type inspection. The type inspection shall be carried out in the user's production. 6.3.2 Inspection Items
Under the working conditions of 4.1, the inspection items are all or part of the technical requirements of this standard except 4.1 and are carried out one by one. 8.3.3 Sampling
The samples for type control inspection are taken from the output that has passed the factory inspection. The following sampling can be carried out randomly before the validity period is determined. When the annual output is less than or equal to 20 units, 1 unit is sampled from any batch: b) When the output is 21-50 units, 2 units are sampled from any batch: a) When the annual output is 51-60 units, 3 units are sampled from the batch. 6.3.4 Judgment Rules
If all items of type inspection are qualified, the product is qualified. If there are unqualified items, they should be re-inspected. If the sample is unqualified, the batch of products is judged to be unqualified for dosage inspection.
Marking, packaging, transportation and storage
7.1 Marking
7.1.1 Each product should have a label fixed in an obvious position, and the label should comply with the relevant provisions of GB/T13306. 7.1.2 The label content should include:
Product model and product name;
b) Name of the pre-washing factory;
Main technical parameters of the product:
d) Overall dimensions:
f) (Product number):
) Date of production,
7.2 Packaging
7.2.1 Product packaging should comply with the relevant provisions of GB/T13306. 7.2.2 Each time the product is shipped, the following technical documents shall be taken along with it:
a) Product instruction manual and accompanying manual; c) Installation and use instructions;
's spare parts list.
7.9 Transportation
Whether the product is transported as a complete machine or in individual pieces, the following provisions shall be met before transportation:
Land transportation shall meet the requirements of land transportation;
Road transportation shall meet the requirements of water transportation; b) Transfer and unloading shall be smooth and free of severe impact. 7.4 Purchase and storage
The product shall be stored in a well-ventilated, dry, rainproof indoor environment without corrosive atmosphere. After one month of storage, it shall be inspected and, if necessary, the anti-rust coating and packaging shall be newly applied.x 0
or:
drop loss rate of the loading,:
barrel flow is solidified, cut off the net content of the loading material, the total is 1000 points (): one bar flow after loading, the total amount of loading material, the unit is "gram (k). 5.9 Determination of the qualified rate of concentrated loading
operate at the nominal production capacity, take water as the medium, the number of samples is 10 times the number of loading heads: the test is carried out in a small production site, it is required to operate at the nominal production capacity, take the loading material as the medium, and the test interval is 20min. According to formula (6) and formula (7), prepare one plug of the minimum and maximum cold room volume standard sample respectively, and determine the net content by weighing, the mass of the measured standard sample minus the mass of the packaging material used is the net content of the leakage material, the net weight of the material divided by the cubic average density of the material is the content marked with volume root.
raie=Y ×98%
=Y,×103%
or:
the minimum amount of standard filling liquid is the total amount, unit is liter (:Y
the net content of swimming pool parts, unit is liter (L) the chemical content of sealed liquid, unit is liter (L). (6
deep comparison: compare the samples with the standard samples, and those that meet the requirements of 4.4.8 are qualified products. If there is a dispute over the unqualified products, use the weighing method to judge: calculate the qualified rate of filling accuracy according to the formula (). ex100
where:
F.-fine filling is now standard, %:
a careful concentration table 5.10 Determination of qualified sealing rate QB/T2738-2G05 Under the nominal production capacity, with technology as the medium, the number of sample barrels is the number of heads: When conducting the test at the production site, it is required to be within the nominal production capacity, with the material loaded in port as the medium, the inspection time is 20mn, and it meets the requirements of 4.4.9. 1 qualified product, according to the formula: - qualified rate: - qualified number of sample barrels, the unit is Tnx; 1uo
A total of 1 (due to poor quality of the two parts and the loss of the ring), the unit is plug 5.11 Determination of the qualified rate of finished products
pieces. The nominal cattle production is operated at the nominal power, with water as the price, and the number of sample barrels is 1 times the number of port heads: when the cattle production site is inspected: it is required to operate under the public production capacity, with port loading materials as the medium, and the test is called 20mln: simplified 4.4.8 requirements The qualified products of the leakage condition are counted as qualified products, and the qualified products that meet the requirements of 4.4. are counted as qualified products. The qualified rate of finished products is calculated according to formula (0). ×100
In the formula;
When the qualified rate of finished products, %:
Wei-out-loading and ≠ about the number of qualified products, the unit is capture: the total number of barrels (due to the poor quality of the phase and the cover itself, the loss is not counted), the typical position is accurate, F
5.12 Noise measurement
The product is in operation under the upper and lower belts. The sound level meter specified in GR/T3768-1996 is used to measure the product's air-conditioning operating noise. The measuring dial is selected from the corresponding half of the standard and the reference body. The measurement distance is strictly recorded in Figure C4 of the sound transmission machine GB/13763-1996. However, the product is not tested in advance. 6 Inspection rules
6.1 Inspection classification
Product inspection classification Factory inspection and type inspection: 6.2 Factory inspection
6.2.1 Inspection items
Meet 4.1.1--4.1.8. Under the operating conditions, the inspection items are not standard requirements of 4.4.1.4.4.2.4.4.4, 4.4.6~4.4.146.2.2 Judgment rules
After the product is manufactured and tested to have a certain operating condition, it shall be inspected! The quality inspection department shall conduct inspection and supervision, and the product can only be issued after the product passes the inspection. When the product passes the inspection, a certificate of conformity shall be issued. If the product passes the inspection for more than 6 years, the new product shall be issued again. If there are any non-conforming items during the inspection, the product can be adjusted. If the product still does not meet the requirements after the inspection, the product shall be deemed non-conforming. 6.3 Type inspection
6. 3.1 Inspection conditions
When one of the following conditions occurs, the type inspection shall be carried out: a) When the production of new products is carried out:
QB/T2736—2005
b) After formal production, the structure, materials, and process have changed significantly, which may affect the product performance: c) When the product is resumed after being discontinued for two years: d) When the inspection results are in good agreement with the type inspection results: When the national supervision agency proposes the requirement for type inspection. The type inspection shall be carried out in the user's production. 6.3.2 Inspection Items
Under the working conditions of 4.1, the inspection items are all or part of the technical requirements of this standard except 4.1 and are carried out one by one. 8.3.3 Sampling
The samples for type control inspection are taken from the output that has passed the factory inspection. The following sampling can be carried out randomly before the validity period is determined. When the annual output is less than or equal to 20 units, 1 unit is sampled from any batch: b) When the output is 21-50 units, 2 units are sampled from any batch: a) When the annual output is 51-60 units, 3 units are sampled from the batch. 6.3.4 Judgment Rules
If all items of type inspection are qualified, the product is qualified. If there are unqualified items, they should be re-inspected. If the sample is unqualified, the batch of products is judged to be unqualified for dosage inspection.
Marking, packaging, transportation and storage
7.1 Marking
7.1.1 Each product should have a label fixed in an obvious position, and the label should comply with the relevant provisions of GB/T13306. 7.1.2 The label content should include:
Product model and product name;
b) Name of the pre-washing factory;
Main technical parameters of the product:
d) Overall dimensions:
f) (Product number):
) Date of production,
7.2 Packaging
7.2.1 Product packaging should comply with the relevant provisions of GB/T13306. 7.2.2 Each time the product is shipped, the following technical documents shall be taken along with it:
a) Product instruction manual and accompanying manual; c) Installation and use instructions;
's spare parts list.
7.9 Transportation
Whether the product is transported as a complete machine or in individual pieces, the following provisions shall be met before transportation:
Land transportation shall meet the requirements of land transportation;
Road transportation shall meet the requirements of water transportation; b) Transfer and unloading shall be smooth and free of severe impact. 7.4 Purchase and storage
The product shall be stored in a well-ventilated, dry, rainproof indoor environment without corrosive atmosphere. After one month of storage, it shall be inspected and, if necessary, the anti-rust coating and packaging shall be newly applied.The nominal cattle production is operated by other forces, with water as the price, and the number of sample barrels is 1 times the number of port gauges: when the cattle production site is inspected: it is required to operate under the public shadow production capacity, with port loading materials as the medium, and the test is called 20mln: the requirements of 4.4.8 are qualified products, and those that meet the requirements of 4.4.7 are qualified products. The qualified rate of finished products is calculated according to formula (0). × 100
In the formula;||tt ||When the qualified rate of finished products, %:
The number of qualified products is about the number of barrels (excluding the loss due to poor quality of the cover itself), the unit is the correct position, F
5.12 Noise measurement
The product is in the upper and lower belts. The sound level meter specified in GR/T3768-1996 is used to measure the air-conditioning running noise of the product. The measuring table is selected Each certificate corresponds to the new plane eight body industry of the reference body, the measurement distance, the sound transmission whole position strict record machine GB/13763-1996 two record C in Figure C4, but for the product pre-test but not to advance 6 inspection rules
6.1 Inspection classification
Product inspection classification Factory inspection and type inspection: 6.2 Factory inspection
6.2.1 Inspection items
Meet 4.1.1--4.1.8J. Under the working conditions, the inspection plan is not a standard replacement requirement 4.4.1.4.4.2.4.4.4,4.4.6~4.4.146.2.2 Judgment rules
Products are manufactured and tested for a certain period of time, and the quality inspection department must conduct inspection and supervision. Only when the product is qualified can it be issued. When it is issued, the product certificate should be issued. If it exceeds 6, it will be issued again. If there are any non-conformities in the inspection, the product can be corrected and re-processed. If the product still does not conform to the standard after the product is re-processed, the product will be deemed non-conformity. 6.3 Type inspection
6. 3.1 Inspection conditions
When one of the following conditions occurs, the type inspection should be carried out: a) When the production of new products is conducted:
QB/T2736—2005
b) After formal production, the structure, materials, and process are greatly changed, which may affect the product performance: c) When the product is resumed after two years of suspension: d) When the inspection results are significantly different from the type inspection results: When the national regulatory agency proposes to conduct type inspection. The type inspection is carried out in the user's production. 6. 3. 2 Inspection items
When the working conditions meet 41, the inspection items are all or part of the technical requirements of this standard except 4. and are carried out one by one. 8.3.3 Sampling
The samples for type control inspection shall be taken from the output that has passed the factory inspection. The samples can be randomly sampled before the next period of time. When the annual output is less than or equal to 20 units, 1 unit shall be sampled from any batch: b) When the output is 21-50 units, 2 units shall be sampled from any batch: a) When the annual output is 51-60 units, 3 units shall be sampled from the batch. 6.3.4 Judgment rules
The product is qualified if all items of type inspection are qualified. If there are unqualified items, they shall be re-inspected. If the unqualified items are unqualified, the batch of products shall be judged to be unqualified for dosage form inspection.
Marking, packaging, transportation and storage
7.1 Marking
7.1.1 Each product shall be labeled in a conspicuous position, and the label shall comply with the relevant provisions of GB/T13306. 7.1.2 The label content should include:
product model and product name;
b) name of the manufacturer;
core product technical parameters:
d) appearance size:
f) product number:
date of manufacture;
7.2 Packaging
7.2.1 Product packaging should comply with the relevant provisions of GB/T13384. 7.2.2 Each time the product is produced, the following technical support certificates should be brought along at random:
b) product promotion manual and accompanying booklet;
installation and use instructions;
spare parts list.
7.9 Transportation
Whether the product is transported in whole package or in individual packages, the following provisions must be met before transportation: a) Land transportation should meet the requirements of land transportation; b) Road transportation should meet the requirements of water transportation; c) Transfer and unloading should be smooth and free of violent impact. 7.4 Purchase and storage
The product should be stored in a well-ventilated, dry, rainproof and non-corrosive indoor environment. After storage for more than 1 month, the box should be inspected and the anti-rust coating and packaging should be newly applied if necessary.The nominal cattle production is operated by other forces, with water as the price, and the number of sample barrels is 1 times the number of port gauges: when the cattle production site is inspected: it is required to operate under the public shadow production capacity, with port loading materials as the medium, and the test is called 20mln: the requirements of 4.4.8 are qualified products, and those that meet the requirements of 4.4.7 are qualified products. The qualified rate of finished products is calculated according to formula (0). × 100
In the formula;||tt ||When the qualified rate of finished products, %:
The number of qualified products is about the number of barrels (excluding the loss due to poor quality of the cover itself), the unit is the correct position, F
5.12 Noise measurement
The product is in the upper and lower belts. The sound level meter specified in GR/T3768-1996 is used to measure the air-conditioning running noise of the product. The measuring table is selected Each certificate corresponds to the new plane eight body industry of the reference body, the measurement distance, the sound transmission whole position strict record machine GB/13763-1996 two record C in Figure C4, but for the product pre-test but not to advance 6 inspection rules
6.1 Inspection classification
Product inspection classification Factory inspection and type inspection: 6.2 Factory inspection
6.2.1 Inspection items
Meet 4.1.1--4.1.8J. Under the working conditions, the inspection plan is not a standard replacement requirement 4.4.1.4.4.2.4.4.4,4.4.6~4.4.146.2.2 Judgment rules
Products are manufactured and tested for a certain period of time, and the quality inspection department must conduct inspection and supervision. Only when the product is qualified can it be issued. When it is issued, the product certificate should be issued. If it exceeds 6, it will be issued again. If there are any non-conformities in the inspection, the product can be corrected and re-processed. If the product still does not conform to the standard after the product is re-processed, the product will be deemed non-conformity. 6.3 Type inspection
6. 3.1 Inspection conditions
When one of the following conditions occurs, the type inspection should be carried out: a) When the production of new products is conducted:
QB/T2736—2005
b) After formal production, the structure, materials, and process are greatly changed, which may affect the product performance: c) When the product is resumed after two years of suspension: d) When the inspection results are significantly different from the type inspection results: When the national regulatory agency proposes to conduct type inspection. The type inspection is carried out in the user's production. 6. 3. 2 Inspection items
When the working conditions meet 41, the inspection items are all or part of the technical requirements of this standard except 4. and are carried out one by one. 8.3.3 Sampling
The samples for type control inspection shall be taken from the output that has passed the factory inspection. The samples can be randomly sampled before the next period of time. When the annual output is less than or equal to 20 units, 1 unit shall be sampled from any batch: b) When the output is 21-50 units, 2 units shall be sampled from any batch: a) When the annual output is 51-60 units, 3 units shall be sampled from the batch. 6.3.4 Judgment rules
The product is qualified if all items of type inspection are qualified. If there are unqualified items, they shall be re-inspected. If the unqualified items are unqualified, the batch of products shall be judged to be unqualified for dosage form inspection.
Marking, packaging, transportation and storage
7.1 Marking
7.1.1 Each product shall be labeled in a conspicuous position, and the label shall comply with the relevant provisions of GB/T13306. 7.1.2 The label content should include:
product model and product name;
b) name of the manufacturer;
core product technical parameters:
d) appearance size:
f) product number:
date of manufacture;
7.2 Packaging
7.2.1 Product packaging should comply with the relevant provisions of GB/T13384. 7.2.2 Each time the product is produced, the following technical support certificates should be brought along at random:
b) product promotion manual and accompanying booklet;
installation and use instructions;
spare parts list.
7.9 Transportation
Whether the product is transported in whole package or in individual packages, the following provisions must be met before transportation: a) Land transportation should meet the requirements of land transportation; b) Road transportation should meet the requirements of water transportation; c) Transfer and unloading should be smooth and free of violent impact. 7.4 Purchase and storage
The product should be stored in a well-ventilated, dry, rainproof and non-corrosive indoor environment. After storage for more than 1 month, the box should be inspected and the anti-rust coating and packaging should be newly applied if necessary.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.