This part specifies the special requirements for starting devices (except glow starters and ignitors) for fluorescent lamps and other discharge lamps using an AC power supply of less than 1 000 V at 50 Hz or 60 Hz. The starting device can generate a starting pulse of not more than 100 kV and is used with lamps and ballasts specified in IEC 60081, IEC 60188, IEC 60192, IEC 60662, IEC 60901, IEC 61167, GB 18774, GB 16843, GB 19510, GB 19510.10 and other standards. This part does not apply to glow starters or starting devices built into discharge lamps or manually operated starting devices. The requirements for preheating transformers for fluorescent lamps are given by GB 19510.9. GB 19510.2-2005 Lamp controlgear Part 2: Particular requirements for starting devices (other than glow starters) GB19510.2-2005 Standard download decompression password: www.bzxz.net

ICS 22, 140 99
National Standard of the People's Republic of China
GB19510.2—2005/1EC61347-2-1.2000 Lamp controlgear-Part 2: Particular requirements for starting devices (other than glow starters) devices (other than globe start crs)
(IECG13.17-2-1:2000.IDT)
2005-01-18 Issued
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Standardization Administration
2005-08-01 Implementation
Normative documents
·General test instructions
Measures to prevent service contact with physical components
Sea line belt
Protective device
Moisture-proof and insulation·
Dielectric strength|| tt||Winding resistance test
Fault condition
The trend of the disease of the stomach
The standard net voltage of the job.
Mechanical waste
Singing non-dripping air room both
Explore the flow of all parts
Heat resistance, fire resistance and cancer resistance
Separation from the movement
Record A (regulatory appendix)
Record B (normative appendix)
Permanent normative appendix)
Compared to the city giant appendix:
Land standard)
Pressure (normative positive record)
When H standard appendix)
Welcome appendix!
Trap or specification appendix)
GB19510.2-2C05/[EC:61347-2-1.7000 Determine whether the electrical part is capable of generating an electrical discharge. Special requirements for the selection of lamps with special thermal protection devices. Special requirements for the electronic control device of lamps with thermal protection devices. Special requirements for the thermal expansion type lamp. The constant S of the company is not used in the application of the temperature test during the test period.
Chen Xu Method for derivation of national voltage value
Locking test
Technical form of electrical measurement circuit
Figure 1.1 Section
The entire content of this part is mandatory.
GR195 control devices are divided into 15 parts:
Part 1: Electrical requirements and safety requirements
Part 2: Household electrical appliances (except glow door actuators) - Particular requirements: R 19510.2—2005/IFC 61347-2-1:200C Part 1: Standard for step-down converters for fluorescent lamps/alternating current step-down converters: Part 4: Special requirements for alternating current current step-down converters for fluorescent lamps; Part 5: Special requirements for direct current current step-down converters for fluorescent lamps: Part 6: Special requirements for direct current current step-down converters for fluorescent lamps. Before the public: the public medical push license when the special requirements of the national son of the DC town class first loan: before the space before the clear use of DC electronic lock shock device support requirements! The first part of the Beijing interest limit when the performance of the flow of special requirements; the first part: the light extinguishing lamp with the sinking device special requirements: the first part: the special requirements for the lock current of the lamp (except the glory lamp) the first part: the high-frequency cold product dynamic general shape or chemical lamp (need red light with nine sub inverters need special requirements: 1: with the lamp collection currency soft electronic destruction support special requirements, this part B purchase of the British part: consulting the glow! Dynamic look outside the special requirements: this part is used together with GB1951.1 · It is formulated after supplementing and modifying the relevant provisions of 1953.1. The department adopts 61247-2--: 2000 to make bags with 21 points: the special requirements of the new light starter hospital)
department office E1247-2-2
as the compensation for labor use, the department quality, the following consumption according to the nature of the change:] \: 1? 17-2-1 \ received as \ this department \ [6134-2 standard" - discussion \G B11, 2"】Except for 13472【Preface, 14?2"Small remarks:) Remove the "《" format in the international standard; Use a decimal point instead of the "" as a decimal point. For the standards cited in (14, 1-230, there are some standards that have been adopted as Chinese standards. This part uses these national standards or industry standards to replace the interstate standards. The rest of the standards that are not equivalent to our standards are directly used in this part (see non-standard standards). Chapter 1, the control system of the lamp is divided into the following: The following are the national standards and the standards for the future: 151.1 Control devices Part 1: General requirements and safety requirements 161317-1: G1950.2 Control devices of lamps Part 2: 5 automatic devices (special safety requirements for automatic devices except hidden lights 1F: 6134721): 0, Control devices of lamps Part 3: Physical requirements for automatic AC converters of lamps (IF 134r--2
G1951(4) Part 1: Part 2: Requirements for special requirements for lamps for use with common electronic devices GB19510 Part 1: Requirements for the installation of common electronic devices F61M1) Part 10: Requirements for the installation of common electronic devices for use with common electronic devices GB19513.2-2005/1EC 61347-2-1:2000:TRT :14?-2-5):
GB1S516.7, Part 7: Particular requirements for spot ballasts for aircraft lighting IF:61347-2-6; 311U.9, Part 3: Particular requirements for lighting devices IEC613-7-71S:1G. Lamp control devices Part 9: Part 9: Particular requirements for spot ballasts for aircraft lighting FC6147-2-3. GB23131ss3:
11C. Application devices Part 1: Particular requirements for spot ballasts for use with micro-lamps other than incandescent lamps IEC6_32!. R 1445 1995)
(11℃.1 control device Part 11, high cold start & tubular discharge lamp (dead rainbow lamp) with wide-angle conversion solution and special group taste Dong 572:
(H1U5.3.. control table Part 2: with H-type film + line with special requirements IE1347-2113.
This part of the appendix A,, CD. on. G, H..1 is a normative appendix: this part of the China Industrial Standard Conference proposed
This part is fully explained and This part was drafted by the National Center for Quality Supervision and Inspection of Light Industry (Shanghai) Equipment Standardization Technical Committee (55/1C224), Shanghai Yeming Double Lighting Lighting Co., Ltd., Haidong Shengdian Three Co., Ltd., Foshan Quanqi Lighting Co., Ltd., Beijing Lighting Research Institute. Drafters of this part: Qian Ziqi, Zhang Hequan, Yun Baoqi, Li Xueren, Qu Ejie, Yang Xiaoya, Rong Xiurong, etc. CB19510.2-2005/EC 6*347-2-1:2050 This part and the 619510.--3:3310,12 are the preparation and standard of the 50 clauses. It specifies the applicable pressure and the actual test sequence of the series, and also stipulates the necessary supplementary requirements. (11961~F19511% of the parts are independent of each other. If we do not refer to the parts of the G3195.3.1, we will refer to the G22510.1. The requirements of this part are the total requirements of the product. The content of the control device of the lamp of the type specified in 150~1512 is not applicable. 1 Specification || tt || GB 19510.2—2005/1FC:E1347-2-1:200C Lamp control gear, Part 2: Particular requirements for starting devices (other than glow starters) This part specifies special requirements for starting devices for discharge lamps and their components (except glow starters lacking a starting voltage) that use an AC power supply of less than 1000V. The device shall not produce a starting pulse of less than 100V and is compatible with 1EC S0081, IH: 6C1XX, 1EC 6IS, IF: F02, IT: 6090I.1EC 61167, (H 1AYY1, C-58-3. (11C.U, G9511 and other standards for the use of ballast, the use of this belt does not follow the use of Ding Guang start belt or equipment to start the stomach or human-operated children's dynamic device, the requirements for preheating inverters for fluorescent lamps in 19510: give mouth || tt || Note: Sex City 60155.
This section only covers the important international construction flows that can be used to start the device. Performance requirements are shown in G/11965
2 Normative references
The following clauses and parts of the referenced documents become the normative clauses of this part through the introduction of 1 month: The relevant references to these documents, H subsequent room alarm receipt (like the inner wear of the room) are not suitable for the six shadow parts, however, the fundamental sense of the division of the left and the study of whether the latest edition of these parts can be used, all undated documents are called currency documents, or the new version is suitable for part D:
This part adopts H1510, 12 new references, and the following derived standards: 5:1128.15 Electrical chain electrical appliances: Thermal relay (/1140815-18EC(6555-8uo
16843 Single-ended fee RMB safety requirements GR1643-1$97, 1. FC6: 991993 G18774x red light safety requirements 1A7742002.tE633190) GB19510, 1 lamp internal control regulations Part 1: : Stock code and safety requirements (G31951.-2004.TEC11: -7--: [E heart 5 guard earth source, - system report ground measurement voltage flash blue area 1EC6UU68-2-7: environmental test acceptance part 2-75: test test circuit Hl, pin impact test I: n15 I light lamp glow automatic device
I60188 high water
low strict sodium lamp
high two steel sodium lamp
Jinjungang token
safety and safety signs
3 definitions
the meanings given in the unused part (: 13.1 The following definitions are given. 2. 1
Starting device tariingdevice
is a device that is suitable for the gas conditions required by the lamp. This device itself or other components in the circuit must produce a suitable starting device: the light supply must be preheated for the electrode, and the current meter and the current meter form an electric resistor together with the lamp. The product can be a pulse type, for example, a push angle type; or a sound type. 3. 3
Start with working time limit can prevent the long time of actual energy starting (for example, the lamp with deactivated electric model: the product starting device means "stop motion" will mean that the person will start the actual circuit in a more manual and automatic manner, and or the limit of starting the lamp will be reduced in the short term,
so that the trigger can always be prevented from starting formally, which means that the electric impulse of the skin has finally been reduced. 3.4
peak voltage peakvo ltage
The maximum value of the voltage pulse produced by the generator at the user end, 3.5
short-circuit power (power source) khnrt-eirenitpmrerofavn.tagesaurce) is the square of the internal resistance of the power supply at the same terminal under the condition of 3.6
sphericalyparkgup
spherical discharger
There are two pieces of the same nominal point in the table at a certain distance, and the voltage between the strips of the standard element is measured at 15kV.
4General requirements
According to the requirements of B1l0.1 Section 4.
5 General test instructions
Inspection according to the requirements of Chapter 10 and the following additional requirements 5.1 Starting devices for headlights with different electrical characteristics Starting devices for headlights with the same electrical characteristics shall be tested together with the lamps in the most unfavorable state. 5.2 Number of samples
The following number of groups of products shall be tested: 10.5~22.5.2.1 The following number of samples shall be tested: 10.5~22.5.2.2 The following number of samples shall be tested: 10.5~22.5.2.1 ... 501 fee chapter 6 safety requirements are as follows: the power supply will be pushed to the room for self-propelled dynamic distribution, 5 kV or less 1: kV:
ikvnviekv>i
—---5 kw.-okvtl0o kv
7 signs
7.1 mandatory signs
GB19510.2:2005/1EC 61347-2-1:20CC according to the military requirements of B310.172, the i-motor device is clearly and permanently marked with the following signs: 1 in 1, and the standard and
· center peak mark is used as the mark, R peak rot exceeds [500 state mark: the trigger with this voltage is also connected to the danger mark, the overshoot voltage exceeds kV: the mark should be the light symbol in the room (center line symbol! IS>3854.
? The above ship trigger does not need to connect other tape marks, because This trigger is sometimes limited by the specified table. 7.2 Supplementary marking
In addition to the above-mentioned control marking, the following optional markings shall be placed on the starter bone, or the product record or similar text of the control shall be recorded,
30.147.1,),,).,> and> shall be written in time. If the automatic purple setting point and the time limit are added to the pulse current device, the product slogan of the ballast device with automatic device shall be changed! Use the starting bone with specified system
B. Measures to prevent accidental contact with live parts
shall be in accordance with GB195:.10) requirements.
9 Terminal connection
According to the requirements of (l5.03:9.1 Section × Zhuo
10 Protective grounding
According to the requirements of (9510.1 Section 9, 11 Moisture-proof and insulation
Connect according to the requirements of GT14:10,1 Section 11 and the following requirements: Do not use 1 tool to disassemble the book! The component casing and other grounding components are completely removed before disassembly. If there is any, put them together with the main transformer against moisture.
In order to make the test chamber reach the specified content, it is necessary to ensure that the air flow inside is good, and only use the correct heat book test unique new, for the double pool training transformer add source insulation paint: the electric attachment is small 7M2 should pay attention to the wet place is to call, and the insulation level is in the thank you insulation level. The temperature change of the test product is not obvious. In order to achieve the absolute value of the proposed point, the sample will be kept in the lubrication range when there is no power supply, or in a non-ventilated box with humidity:
12 Power panel
According to the requirements of 112 Zhuo and the above requirements:
Electric starter test
For starting devices equipped with high voltage relays, the reverse pulse test under pressure is adopted to check the parts: the starter is placed under 11U% of the rated power supply for one month without lamps, until 51 pulses occur. If necessary, the power supply can be turned on. Note: The starter of the relay must be placed under 11U% of the rated power supply for one month without lamps, until 51 pulses occur. If necessary, the power supply can be turned on. Note: The voltage of the lamp must be continuously generated within 2
CR19510.2—2005/IF: 61247-2-1:2000 Test time. Wave starting device:
and no obvious or significant discharge (signs of electrical stress insulation effect! 1) There should be no brown fire or flying phenomenon! :) In the oscilloscope, there should be no folding or compression phenomenon at the top or tail of the waveform. For the high and low starter, the medium frequency test of -mn is carried out to check the 13th group of heat resistance test
not in accordance with the requirements of 3115-1.1, the test age requirement is still under study, 14 discharge state
contact 1101 4 single requirements and the following additional requirements: 14.1 The starter should not cause excessive heating of the lamp circuit caused by the new discharge when the lamp is discharged, and the winding difference should not exceed the position, for the equipment: 3 room specified external For starters of this size, if the self-heating current of the circuit exceeds the maximum current of 11C60051 and E6091, it can be regarded as meeting this requirement. 14.2 The starter shall not exceed the value specified in 1.2. For the electrodes of the headlights, the increase in the preheating current of the starter circuit does not exceed 5% of the normal value. It is considered to meet this requirement. If the heating mode is not specified, it must be specified. 11. Under the condition that the current of the ballast exceeds the circuit current by % for 5ml? for 1.0 seconds: the mechanical breaker of the starting device shall be lowered or the circuit breaker shall comply with GB/T145. 15. When the corresponding parts are recorded, it can be regulated in accordance with this table. 15. Independent inching device heating || tt || Independent starting device should not operate during normal working period: Note: The optional device can be used: Actual (K2.1 only with the control rate, qualification is shown in the following fast test\inspection: normal recovery light Yingyue one or more of the following conditions flash 1 working status a) the light is in "normal working:
b) the flow passes through the gate station device!
) convex or meter connected to the gate source, if the normal working period appears, the internal deep electricity is formed, and the normal state is maintained:
will be installed in an independent working stomach. The test consists of three members of the old wood correct the uncle. In use, these daytime panels have a dark black surface, with a thickness of mm--mr, and are designed to be placed in the housing section and the port. The swimming device is fixed to the north, as close to the wall as possible, and the other surfaces of the swimming device are at least Cmm in total. The location of the test should be as far as possible from the five internal tables of the test box, and the
test should be carried out according to the reduced record. The test is carried out indoors or in the stable environment of the specified standard. 15. 1. Prohibit working
will be connected or delayed to stop the control change. When the lamp is in the specified state, adjust the lamp current to the rated value by changing the setting requirements. Under this condition, start the device and work until the specified state is reached. The humidity of the parts should not exceed 70CC. The values ​​specified in Tables 12.1 and 12.2 are close to the specified values. The readings used should be based on the standard requirements. The main light type should be consistent with the requirements of 15.2 Abnormal working
Start the device with the control efficiency requirements and applicable materials. When testing, use the anti-reverse activation lamp or use the replacement lamp specified in the IECb061: Chinese lamp reference table. Use a new and suitable lamp with a rated value and 4
pass the test.
Connect the lamp according to the normal use requirements, t:K 79-13.2—2005/TFC 5 347-2-1:7730 The trigger shall be operated under the specified minimum conditions of 05% of the working time under the condition of non-abnormal phenomenon, or the trigger with working time limit shall be stopped within or before the time limit specified in the specification (. The temperature of the non-northeast test part shall not exceed the value specified in CC6: Table 12. After the automatic assembly completes this test and cools down, the following parts shall be connected:) The yellow start mark shall still be clear and obvious b1 The driving device shall be able to withstand the dielectric leakage check determined in Section 12 of this section The test voltage should not be less than 75% of the value specified in Table T1S:1G.1. When the trigger voltage is insufficient, the circuit should be operated under a low load of 23% (maximum compensation voltage) and the pulse should not exceed 1 kV, and the pulse voltage specified in the relevant lamp parameter table should be included. If not specified in the corresponding lamp efficiency table, the maximum compensation voltage of the pulse at the trigger end of 1 kV should not exceed 1.3 when it is under rated power supply voltage and 21% (maximum compensation voltage) and the manufacturer should declare. For peak values ​​below kV, the measurement should be carried out with a liquid indicator or an electrostatic meter. For peak compensation pulses above kV, a spherical discharger can be used for measurement. The method specified in [E and the appendix of this part] should be adopted. Note: The standing position can be used as the real life situation of the product with the pressure support in the heart. Press the finger to start in the practice of fast: uM
Editor abandon:
Interval: MH
Can be measured in the near time. 17 Machine precautions
17, 11 days of the environment start the stomach and do not use the service history of the user on the easy to press and follow the parts should have the specified mechanical strength
Zhen mass production 10 to one start the Ling Department and parts and all H equipment 115 complete the size of the start monitoring should be subject to the record of the specified rolling test in 1.3, each sample should be subjected to 21 times of hand drop belt, and there is no problem of service affecting its tightness when the full color,
And the start or ton of more than 1 device and parts should be subject to the first casting test specified in 1.1 of the record. The test shows that the energy limit within the day is C.35m. The single-installation 17n2
test user, the column product does not have the support to the river to cut the damage of the safe operation: 17.2 The decision type is fixed and the parts that can be replaced only when the starting device is replaced are not used. In addition to the normal warning, it also requires the acceptance of the line 3. "Into the m short loss test. Twist the metal shell of the power part to close the foot. The torque torch rises from the zero medium to the specified value. The test product does not have any safety loss. 18 Structure
According to 19510.1 Section 1: General requirements, the following additional requirements shall be met: 18! There shall be a faster starting device with a quick start function (including a double-flash or single-flash protection) that can be used to cut off the starting circuit and/or change the starting medium voltage when the lamp fails to be ignited.
GR 19510.2—2005/IEC:61347-2-1:2000 Some replacements for circuit breakers may be devices capable of limiting the starting current and of limiting the current allowed to pass not more than 10% of the rated current of the lamp. The entire lamp current carrying circuit and other parts need not be subjected to a load greater than the rated current of the lamp: Compliance shall be verified by the tests described in clause 14 or clause 15. The trigger components shall be equipped with a time-limited control device for pulse voltages exceeding ukV. The trigger pulses shall be kept within 3 hours without the full triggering ignition point. After the time limit has been reduced, the starting pulse is only allowed to be disconnected from the power supply and then reconnected to the power supply.
A 10kV or less 5%V contactor should be installed in the starting time limit device. The device should cut off the circuit within 35 seconds. After the circuit is cut off, the starting circuit can only be completed after the power is disconnected and then connected to the power source.
Qualification is tested by the test specified in the Japanese standard and Chapter 1. 18.3 It can be used with the IEC50155 test device to form an anti-radio interference device. The effect of the device should be the same as the effect of the anti-radio interference capacitor specified in 7.13 of [IEC50155]. 18 Power supply and electrical space
Safety GB 1S513.1 Section 16 requirements, 20 screws. Load-carrying parts and connectors
According to the requirements of GH1S:10,: Chapter 17. 21 heat, fire and leakage resistance
Connect CB 10510.1 Chapter 13 flash requirements. 22 sulfur corrosion resistance
According to the requirements of GB19510, 1999,
General Office. Pre-light current (single approx.
same current (peak signal):
State board: cathode voltage:
DisE kV
Jxyu]. 3 A bzxZ.net
Let: For example, the adjacent parts are GYSC type high-voltage rectifier high-voltage electrical appliances for color motors
Tel:
C-1:90 p3
fixed voltage F.
ti:6. 3 kV
(1 time two torsion stop value,
high voltage intense its proposal
static||national
station large editing sea time shot
release
1 said or dangerous
make the high-altitude electric discharge device
idea economic education should be based on the age of the flow point
the center of the guidance of the technical point
and the (with the small electric
GR19510.2-2035/IEC61347-2-1,2000 Figure 1 trigger starting voltage measurement circuit2 Abnormal work
Start the control system with the required efficiency and applicable materials. When testing, use the anti-reverse activated lamp or the replacement lamp specified in the reference table of IECb061: 4. The lock surface should be tested with a new and suitable lamp with an average rated value and 4.0 mm.
Connect the lamp according to the normal use requirements, t:K 79-13.2—2005/TFC 5 347-2-1:7730 In non-abnormal conditions, the trigger should be under the specified small conditions of 05 years. The workpiece should be corrected in accordance with the regulations. For the benefit of the next state, or each time the working time limit of the brand trigger is limited, it should stop within or before the time limit required in the book. (. The temperature of the non-north test part should not exceed CC6: the value specified in Table 12. After the automatic assembly completes this test and cools down, the following parts should be connected:) The yellow start-up mark should still be clear and obvious b1 The driving device should be able to withstand the dielectric leakage rate determined in Section 12 of this sub-section. The test age should not be damaged by fatigue. The test fee should be 75% of the value specified in the T1S:1G.1 table: the supply voltage of the trigger should not be lower than 533V. When the trigger is not able to use the diagram, the line should be operated under the rated current with a low load capacity of 23V (the surge or pulse should not be greater than 1 kV), and the surge voltage specified in the relevant lamp parameter table should be added. If the corresponding lamp is not specified in the cost-effectiveness table, the pulse should be 10 kV at the trigger end. When it is under the rated power supply voltage and the car is 21 The maximum voltage of the negative or positive pulse should not exceed 1.3, which shall be stated by the manufacturer. For peaks below kV, use a liquid tracer or an electrostatic meter to measure. For peaks above kV, use a spherical discharger to measure. The method specified in [E and the appendix of this part] shall be used. Note: The standing type indicator can be used. The actual situation of the product and the product with the same voltage as the standard is as follows: uM||tt ||Editor abandoned:
Interval frequency: MH
The small table in the near line is measured for the wine party. 17 machine ring recording degree
17, 11 days of state starter stomach and do not use the month 1 only on the service history of the user installation on the easy to press and the parts should have a certain mechanical strong disk
Zhen mass production 10 with a starter and parts and all H equipment 115 complete the size of the starter monitor should accept the recording Ding 1.3 The rolling test specified in the present invention shall be that each sample shall be subjected to 21 drops without any damage affecting its tightness. The equipment and parts with a capacity of more than 1 kg shall be subjected to the first casting test specified in 1.1 of the present invention. The test shall be carried out for 35 minutes and the product shall not be damaged in a way that would affect its safe transportation. 17.2 In addition to the normal warning of the owner when using the fixed-type dynamic device and the parts that can only be replaced on the starting device, the 3. "m short loss test" of the line is also required. The power part of the metal shell is clamped tightly and the torque is applied to the closed foot. The torque is increased from the specified value of the test. The product has no reason to increase the safety loss. 18 Structure || tt || According to 19510.1 Section 1: Regular requirements, the following additional requirements are required: 18! There are faster starting devices that can only be replaced by chopsticks. The parts and equipment of the chain and all the parts of the equipment must have an effective double-flash insulation requirement (including sweeping and stopping) or a single-flash insulation requirement. 18.2 The structure of the starting device equipped with a circuit breaker can also cut off the starting line and/or change the starting medium voltage when the lamp fails to be ignited.
GR 19510.2—2005/IEC:61347-2-1:2000 Some replacements for circuit breakers may be devices capable of limiting the starting current, which are designed to allow a current not exceeding 10% of the rated lamp current. The entire lamp current carrying circuit and other parts need not be subject to a load greater than the rated lamp current: Compliance is verified by tests as described in clause 14 or clause 15, with the initiator having an impulse voltage exceeding ukV and a control device installed during operation. The circuit breaker is operated within 3 hours without the presence of a full triggering pulse. The starting pulse is only allowed to be generated after the power is disconnected and the power is connected again.
A trigger with a voltage less than 5%V and equal to 10kV should be installed in the starting time limiting device. The device should cut off the power within 35 seconds. After the line is cut off by the time limit, the starting pulse is only allowed to be generated after the trigger is disconnected and the power is connected again.
Qualification is tested by the tests specified in the regulations and Chapter 1. 18.3 It can be used together with the test device specified in IE:50155 to form an anti-radio interference device. The effect of the device should be equal to the effect of the anti-radio interference capacitor specified in 7.13 of [EC50155]. 18 The power supply and electrical connection must comply with the requirements of GB 1S513.1 Section 16. 20 Screws, mounting parts and connectors must comply with the requirements of GH1S:10:17. 21 Heat, fire and leakage current resistance must comply with the requirements of CB 10510.1 Section 13. 22 Sulfur corrosion resistance According to GB19510, 1990, the general hall. Pre-production current (single approx.) and current (peak): board: cathode: DisE kV Jxyu]. 3 A. For example, the suitable component is GYSC type high-voltage rectifier for color motors. Phone: C-1: 90 p3. Condensation voltage: 6. 3 kv
(1 time the two support limit value,
high voltage intense its proposal
static||national
station large-scale transfer sea
release
1 said or dangerous
make the high-altitude electric discharge device
think of the economic development of the education should be the age of the flow point
the center of the guidance of the technical points
and the (with the small electric
GR19510.2-2035/IEC61347-2-1,2000 Figure 1 trigger starting voltage measurement circuit2 Abnormal work
Start the control system with the required efficiency and applicable materials. When testing, use the anti-reverse activated lamp or the replacement lamp specified in the reference table of IECb061: 4. The lock surface should be tested with a new and suitable lamp with an average rated value and 4.0 mm.
Connect the lamp according to the normal use requirements, t:K 79-13.2—2005/TFC 5 347-2-1:7730 In non-abnormal conditions, the trigger should be under the specified small conditions of 05 years. The workpiece should be corrected in accordance with the regulations. For the benefit of the next state, or each time the working time limit of the brand trigger is limited, it should stop within or before the time limit required in the book. (. The temperature of the non-north test part should not exceed CC6: the value specified in Table 12. After the automatic assembly completes this test and cools down, the following parts should be connected:) The yellow start-up mark should still be clear and obvious b1 The driving device should be able to withstand the dielectric leakage rate determined in Section 12 of this sub-section. The test age should not be damaged by fatigue. The test fee should be 75% of the value specified in the T1S:1G.1 table: the supply voltage of the trigger should not be lower than 533V. When the trigger is not able to use the diagram, the line should be operated under the rated current with a low load capacity of 23V (the surge or pulse should not be greater than 1 kV), and the surge voltage specified in the relevant lamp parameter table should be added. If the corresponding lamp is not specified in the cost-effectiveness table, the pulse should be 10 kV at the trigger end. When it is under the rated power supply voltage and the car is 21 The maximum voltage of the negative or positive pulse should not exceed 1.3, which shall be stated by the manufacturer. For peaks below kV, use a liquid tracer or an electrostatic meter to measure. For peaks above kV, use a spherical discharger to measure. The method specified in [E and the appendix of this part] shall be used. Note: The standing type indicator can be used. The actual situation of the product and the product with the same voltage as the standard is as follows: uM||tt ||Editor abandoned:
Interval frequency: MH
The small table in the near line is measured for the wine party. 17 machine ring recording degree
17, 11 days of state starter stomach and do not use the month 1 only on the service history of the user installation on the easy to press and the parts should have a certain mechanical strong disk
Zhen mass production 10 with a starter and parts and all H equipment 115 complete the size of the starter monitor should accept the recording Ding 1.3 The rolling test specified in the present invention shall be that each sample shall be subjected to 21 drops without any damage affecting its tightness. The equipment and parts with a capacity of more than 1 kg shall be subjected to the first casting test specified in 1.1 of the present invention. The test shall be carried out for 35 minutes and the product shall not be damaged in a way that would affect its safe transportation. 17.2 In addition to the normal warning of the owner when using the fixed-type dynamic device and the parts that can only be replaced on the starting device, the 3. "m short loss test" of the line is also required. The power part of the metal shell is clamped tightly and the torque is applied to the closed foot. The torque is increased from the specified value of the test. The product has no reason to increase the safety loss. 18 Structure || tt || According to 19510.1 Section 1: Regular requirements, the following additional requirements are required: 18! There are faster starting devices that can only be replaced by chopsticks. The parts and equipment of the chain and all the parts of the equipment must have an effective double-flash insulation requirement (including sweeping and stopping) or a single-flash insulation requirement. 18.2 The structure of the starting device equipped with a circuit breaker can also cut off the starting line and/or change the starting medium voltage when the lamp fails to be ignited.
GR 19510.2—2005/IEC:61347-2-1:2000 Some replacements for circuit breakers may be devices capable of limiting the starting current, which are designed to allow a current not exceeding 10% of the rated lamp current. The entire lamp current carrying circuit and other parts need not be subject to a load greater than the rated lamp current: Compliance is verified by tests as described in clause 14 or clause 15, with the initiator having an impulse voltage exceeding ukV and a control device installed during operation. The circuit breaker is operated within 3 hours without the presence of a full triggering pulse. The starting pulse is only allowed to be generated after the power is disconnected and the power is connected again.
A trigger with a voltage less than 5%V and equal to 10kV should be installed in the starting time limiting device. The device should cut off the power within 35 seconds. After the line is cut off by the time limit, the starting pulse is only allowed to be generated after the trigger is disconnected and the power is connected again.
Qualification is tested by the tests specified in the regulations and Chapter 1. 18.3 It can be used together with the test device specified in IE:50155 to form an anti-radio interference device. The effect of the device should be equal to the effect of the anti-radio interference capacitor specified in 7.13 of [EC50155]. 18 The power supply and electrical connection must comply with the requirements of GB 1S513.1 Section 16. 20 Screws, mounting parts and connectors must comply with the requirements of GH1S:10:17. 21 Heat, fire and leakage current resistance must comply with the requirements of CB 10510.1 Section 13. 22 Sulfur corrosion resistance According to GB19510, 1990, the general hall. Pre-production current (single approx.) and current (peak): board: cathode: DisE kV Jxyu]. 3 A. For example, the suitable component is GYSC type high-voltage rectifier for color motors. Phone: C-1: 90 p3. Condensation voltage: 6. 3 kv
(1 time the two support limit value,
high voltage intense its proposal
static||national
station large-scale transfer sea
release
1 said or dangerous
make the high-altitude electric discharge device
think of the economic development of the education should be the age of the flow point
the center of the guidance of the technical points
and the (with the small electric
GR19510.2-2035/IEC61347-2-1,2000 Figure 1 trigger starting voltage measurement circuit35m single installation 17n2
test user, the fence product does not have the support to the river can cut the damage of safe transportation: 17.2 children more decision type fixed installation needs and does not use only can replace the start of the stomach on the easy chain necessary parts in addition to the change of the normal words have the report, but also become the line of the 3. "m short damage test. Torsion is applied to the metal shell of the power clamp. The torque is increased from the zero value of the test product. The safety of the case can not be increased by 18 structure|| tt||According to 19510.1 Section 1: The following additional requirements are required: 18! There are all kinds of quick start devices that can be installed with only one type of starter and can reduce the number of parts and components of the equipment and equipment (including the sweep stop) with an effective double-fault or single-fault 18.2 The structure of the starting device equipped with a circuit breaker can also cut off the starting circuit and/or change the starting medium voltage when the lamp fails to be ignited by the fuse.
GR 19510.2—2005/IEC:61347-2-1:2000 Some replacements for circuit breakers may be devices capable of limiting the starting current and of limiting the current allowed to pass not more than 10% of the rated current of the lamp. The entire lamp current carrying circuit and other parts need not be subjected to a load greater than the rated current of the lamp: Compliance shall be verified by the tests described in clause 14 or clause 15. The trigger components shall be equipped with a time-limited control device for pulse voltages exceeding ukV. The trigger pulses shall be kept within 3 hours without the full triggering ignition point. After the time limit has been reduced, the starting pulse is only allowed to be disconnected from the power supply and then reconnected to the power supply.
A 10kV or less 5%V contactor should be installed in the starting time limit device. The device should cut off the circuit within 35 seconds. After the circuit is cut off, the starting circuit can only be completed after the power is disconnected and then connected to the power source.
Qualification is tested by the test specified in the Japanese standard and Chapter 1. 18.3 It can be used with the IEC50155 test device to form an anti-radio interference device. The effect of the device should be the same as the effect of the anti-radio interference capacitor specified in 7.13 of [IEC50155]. 18 Power supply and electrical space
Safety GB 1S513.1 Section 16 requirements, 20 screws. Load-carrying parts and connectors
According to the requirements of GH1S:10,: Chapter 17. 21 heat, fire and leakage resistance
Connect CB 10510.1 Chapter 13 flash requirements. 22 sulfur corrosion resistance
According to the requirements of GB19510, 1999,
General Office. Pre-light current (single approx.
same current (peak signal):
State board: cathode voltage:
DisE kV
Jxyu]. 3 A
Let: For example, the adjacent parts are GYSC type high-voltage rectifier high-voltage electrical appliances for color motors
Tel:
C-1:90 p3
fixed voltage F.
ti:6. 3 kV
(1 time two torsion stop value,
high voltage intense its proposal
static||national
station large editing sea time shot
release
1 said or dangerous
make the high-altitude electric discharge device
idea economic education should be based on the age of the flow point
the center of the guidance of the technical point
and the (with the small electric
GR19510.2-2035/IEC61347-2-1,2000 Figure 1 trigger starting voltage measurement circuit35m single installation 17n2
test user, the fence product does not have the support to the river can cut the damage of safe transportation: 17.2 children more decision type fixed installation needs and does not use only can replace the start of the stomach on the easy chain necessary parts in addition to the change of the normal words have the report, but also become the line of the 3. "m short damage test. Torsion is applied to the metal shell of the power clamp. The torque is increased from the zero value of the test product. The safety of the case can not be increased by 18 structure|| tt||According to 19510.1 Section 1: The following additional requirements are required: 18! There are all kinds of quick start devices that can be installed with only one type of starter and can reduce the number of parts and components of the equipment and equipment (including the sweep stop) with an effective double-fault or single-fault 18.2 The structure of the starting device equipped with a circuit breaker can also cut off the starting circuit and/or change the starting medium voltage when the lamp fails to be ignited by the fuse.
GR 19510.2—2005/IEC:61347-2-1:2000 Some replacements for circuit breakers may be devices capable of limiting the starting current and of limiting the current allowed to pass not more than 10% of the rated current of the lamp. The entire lamp current carrying circuit and other parts need not be subjected to a load greater than the rated current of the lamp: Compliance shall be verified by the tests described in clause 14 or clause 15. The trigger components shall be equipped with a time-limited control device for pulse voltages exceeding ukV. The trigger pulses shall be kept within 3 hours without the full triggering ignition point. After the time limit has been reduced, the starting pulse is only allowed to be disconnected from the power supply and then reconnected to the power supply.
A 10kV or less 5%V contactor should be installed in the starting time limit device. The device should cut off the circuit within 35 seconds. After the circuit is cut off, the starting circuit can only be completed after the power is disconnected and then connected to the power source.
Qualification is tested by the test specified in the Japanese standard and Chapter 1. 18.3 It can be used with the IEC50155 test device to form an anti-radio interference device. The effect of the device should be the same as the effect of the anti-radio interference capacitor specified in 7.13 of [IEC50155]. 18 Power supply and electrical space
Safety GB 1S513.1 Section 16 requirements, 20 screws. Load-carrying parts and connectors
According to the requirements of GH1S:10,: Chapter 17. 21 heat, fire and leakage resistance
Connect CB 10510.1 Chapter 13 flash requirements. 22 sulfur corrosion resistance
According to the requirements of GB19510, 1999,
General Office. Pre-light current (single approx.
same current (peak signal):
State board: cathode voltage:
DisE kV
Jxyu]. 3 A
Let: For example, the adjacent parts are GYSC type high-voltage rectifier high-voltage electrical appliances for color motors
Tel:
C-1:90 p3
fixed voltage F.
ti:6. 3 kV
(1 time two torsion stop value,
high voltage intense its proposal
static||national
station large editing sea time shot
release
1 said or dangerous
make the high-altitude electric discharge device
idea economic education should be based on the age of the flow point
the center of the guidance of the technical point
and the (with the small electric
GR19510.2-2035/IEC61347-2-1,2000 Figure 1 trigger starting voltage measurement circuit
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.