HG/T 3569-2001 Determination of light absorption of color formers HG/T3569-2001 standard download decompression password: www.bzxz.net

8 37.040.20:71, 040. 50
Chemical Industry Standard of the People's Republic of China
HIG/T356935702001
Determination of light absorption of coupler
Photographic chemicals Potassium bromide (for emulsion)
2002-01-24
Implementation on 2002-07-01
Issued by the State Economic and Trade Commission
Registration No.: 101292002
HG/T3569—2001
This standard is based on the chemical industry standard H/553—0 Determination of light absorption of coupler. The main differences between this standard and HG/T3669 are: Part of the analysis steps are modified.
The standard name is modified.
4 The date of implementation of the standard: Contemporary Zhe 1:3553-!!, the production standard is issued by the former National Petroleum and Beijing Industry Bureau Policy and Regulations Department, and the scientific standard is issued by the National Nuclear Photosensitive Materials Standardization Technical Committee. 6 The starting date of the standard: Zhongyue Lechuang Cavity Film Dongtuan Photosensitive Chemical Research Institute, Zhongyue Xuekai Cavity Film Company. The drafters of this standard: Tu Xing, Guan Ronghua. This standard was revised and issued as a professional standard 2FG850- in 1990, and adjusted to a recommended chemical industry standard in 1999, and renumbered as IIG/T3E6S
6930.
1 ScopebzxZ.net
Chemical Industry Standard of the People's Republic of China
Determination of light absorption of couplers
Determination of light absorption of couplers
This standard specifies the method for determining light absorption of couplers. This standard applies to 1 oil-soluble couplers with a colored appearance. 2 Referenced Standards
HG/T3569—2001
Representative China [G/155919
The provisions contained in the underlined standard constitute the main points of this standard through reference in this standard. When this standard is revised, the versions shown are valid. All standards will be reviewed: All parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T6_9-1988 Sampling and Acceptance Rules for Chemical Reagents [15/T9721-19 Chemical Reagents Absorption Spectrophotometry (UV and UV-Visible Part)] 3 Method Summary
Weigh a certain amount of test sample, dissolve it with a specified solvent and prepare a drop of solution with a certain concentration, use a spectrophotometer to measure the concentration of the solution in a specified range, and calculate the absorbance coefficient of the reagent. The absorbance coefficient of the color former quantitatively reflects the degree of colored impurities in the reagent. · Reagents
Mononitrogen-containing alkane: pure,
Hazard: dangerous if inhaled, use with appropriate ventilation. Harmful if swallowed. 5 Instruments and equipment
5.1 Spectrophotometer: The sensitivity shall comply with the provisions of GB/T972, 5.2: Analytical balance: The sensitivity is 0.mg
5.3 Volumetric bottle: The concentration is 10 1nL.
6 Sample
Details according to GB/T619:
7 Steps
Weigh 1.0g sample (0.0022g) on ​​the analytical scale. Pour 10ml into a volumetric flask. Add difluoromethane and stir gently to dissolve the sample completely. Use monoxide to dilute the carbon rod to the scale and measure the sample. Use 1m sodium bicarbonate absorption cell on the spectrophotometer to measure the methane ignition rate. Compared with the solution, at the detection wavelength of 420nm, measure the absorbance of the sample. Approved by the National Economic and Financial Affairs Commission on January 24, 2002, implemented on July 1, 2002
HG/T:3569-2001
Note: Individual colorants can be obtained at any time, in any area, or without any control. 8 Analysis results
The colorant absorption coefficient (e) is calculated according to the following formula: In the formula; Absorbance Coefficient, sensor trichloromethane micro-unit iridium degree and unit optical path length, at the specified wavelength (4211m> absorbance m:mL/(g-cm)
sample quotient's account luminosity;
sample whole law -B/mL
- avoid the optical path length of the sample tumor fluid. 9 allowable error
the difference between the results of two effective parallel measurements shall not be greater than (,r3nmL/-cm), take the previous error The sample arithmetic value is the result of the test.
Test report
The test report should include the following contents:
2. Sample name, batch date, manufacturer,
b. Test instruments and equipment;
c. All test data and results;
, test date, test personnel:
e: If the density, swimming speed, detection wavelength are different from those of the first test, it should be explained:
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.