This standard specifies the basic parameters, appearance and installation dimensions, technical requirements, test methods, acceptance rules and markings, packaging, transportation and storage of micro electric lubrication pumps. This standard is applicable to the lubrication system of metal cutting machine tools and forging machinery, and can also be used as a reference for the lubrication systems of other machines. JB/T 8651.3-1997 Machine tool lubrication system components Micro electric lubrication pump JB/T8651.3-1997 Standard download decompression password: www.bzxz.net

The People's Republic of China Machinery Industry Standardization
JB/T8651.3-1997
Machine Tool Lubrication System Components
Micro Electric Lubrication Pump
1997-08-18 Issued
Ministry of Machinery Industry of the People's Republic of China
1998-01-01 Implementation
JB/T 8653.3 --1997
This standard is proposed by the Beijing Machine Tool Research Institute of the Ministry of Machinery Industry. The drafting units of this standard are: Beijing Machine Tool Research Institute of the Ministry of Machinery Industry, Zhejiang Yongpin Lujing Machinery Co., Ltd., Beijing No. 1 Tao Bed Factory, Beijing No. 2 Machine Tool! .
Machinery Industry Standard of the People's Republic of China
Machine Tool Lubrication System Parts
Micro Electric Lubrication Pump
JB/I 8651.31997
This standard defines the basic technical equivalent, external dimensions and installation dimensions, technical requirements, test methods, acceptance criteria, packaging, and necessary inspections of electric lubrication pumps.
This standard is applicable to the lubrication systems of mechanical tools and other mechanical systems. Other mechanical systems can be used as references. 2 Referenced Standards
The following standards contain provisions that are cited in this standard as the provisions indicated. When this standard was published, the versions shown were valid. All specifications are subject to revision. The use of this note may be subject to the use of the following new versions of the standard, GR 6-R5.
GB19190
GB4UI-5
GR-92-ES
Open the original order
Packaging storage and transportation pictorial symbols
Calcium-based lubricants
Cinnamon-based lubricants
GB/T6226.1-996T Industrial machinery and electrical equipment Part 1: General technical requirements
E732494
CB/T 13R06-0:
JB/T 3207-91
JB/T 11219
B/218983
2B J50 00S -8X
ZRJ50004-58
2BJ5001389
3 Product marking
3.1 Model
Pressure potassium-based lubricant
Machine tool accessories product packaging traces use large strips of lubricant core parts and model reduction method
Machine tool parts random technical documents reduction
Jin Guo can cut machine tool cleanliness determination
Jin Wang can static machine tool
Noise level determination
Machine tool anti-mirror rejection technical conditions
Micro electric cutting system type according to 1B/T121 standard system, B
Xiang Gong number, micro
Lan Ai Han: oil barrel wear agent
([: c.4 1.. I . 1. 4 [., I. 1.5 I.. N: 2.3 t) Table number: Displacement, 0. 1 mL/stroke Nominal pressure level (level 6.3Ma: J level: 1MF:) Product name code: Electric feather attachment
Approved by the Ministry of Machinery Industry on August 18, 1997
Implemented on January 1, 1998
3.2 Long six-side
J8651.3--1
Displacement force is level U.1 stroke note area is 1.4 [. Micro initial mark example BJ
JB/T8652.$-1907
4 Basic model number, appearance and installation size
4.1 Basic distribution (condition table 1)
Public pressure
DL-J3. 1: I w
-1.1: [ w
DB-1_i1 W
index ratio
4.2External & installation dimensions see Figure 1. Figure 2 and Commission) Public capital drawing
anL/stroke
Consumer consultation welcome
(standard
5×1 note
-15.1/ 1
JB/I 8651.3 -1997
Dynamic control certificate
Clean book:
Metallic dyeing method
>Ms?I5
5 Technical requirements
JB/T8651-3-1997
5.1 Working under the temperature of 40℃. Use high quality needle with a diameter of 25.1.in5:1/1cmm, etc. G401.G40B324 requirements
5.2 The material, processing quality, heat treatment and surface treatment of all parts shall comply with the requirements of the production drawings and relevant technical specifications: 5.3 The nominal pressure, delivery, oil volume ratio shall not be less than the standard parts specified in Table 1, and the purchased parts shall meet the relevant standards. 5.5 The appearance surface shall be smooth and shall not have defects such as quality, slowness, and resistance. 5.6 During the empty load test, the total oil discharge should be Y. In order to ensure the normal operation and the correct sound, the sealing joints and seals should not be leaking. 9 Under the rated load, the output force of each discharge should not be less than the value specified in Table 1. 5.10 Under nominal pressure, the sound pressure level of the item shall not exceed the rated value of 75d3A). Check the activity of the source and the cleaning of the internal cleaning material. 5.12 Under nominal pressure of 1c0%, the service life shall be at least ten times. 3.13 The overload protection of the motor shall comply with the provisions of B/T5226, 1. Test method: 6.1 Test conditions: 6. 1.I Test medium: U\~.1\ lithium-based. 4 Final test condition, 15~30 minutes:
heart. 2 Air test
actual pull release snatch complaint, standard pump frequency set speed, air transport IrL. lubrication principle should comply with the provisions of Taiwan 5.6 standard. 6.3 Pressure test
under nominal! Pressure min oil case should comply with the visual specification of the product? 6.4 Close test
1. Travel with the public transfer under normal state, run 5 ir., oil system network match 5. 5. The maximum oil output (test principle
at the nominal mass point 100 change soil 10 new state, respectively measure the oil outlet 10 three work source theory large single note value to meet the requirements of 5! 6.6 Cleaning and grinding test
from the lubrication after assembly, the sample is tested according to 2BJSUOF3 medium weight method, and its value pressure is not greater than the provisions of clothing 3. 6. For the city test
according to 7150C1 required rate determination, should be derived from 5.10 reduction provisions: 6.8 annual test
JB/T8651.3I997
- oil test system pressure * pressure lubrication cup
certification nominal pressure 100% ± 10% of the working state, on the test bench simulating the working conditions of the lubrication system, the cumulative number should be in accordance with 5.18. Acceptance Rules
1 Each micro electric lubrication system shall be tested before leaving the factory or the contents specified in 8.1, 5.2, 6.3 and 6.4 shall be tested. 7.2 Each micro electric lubrication system shall be tested on the production line! The diameter shall be inspected and qualified before it can be shipped to the factory. 7.3 Type test bZxz.net
For the expansion of trial products, or due to the micro electric system control, village materials and technology changes, type test shall be carried out. The contents of type test include:
! All contents of factory test:
b) sound test:
c) sound test:
cleaning test.
8 Marking, packaging, transportation and storage
8.1 Each micro electric lubrication system shall have a product label in an appropriate and obvious position. Its type and size shall comply with the provisions of T330/T330. The label contains the following information: 1.1 Product name:
) Public vehicle power 1
c) Public vehicle
d) Date of manufacture;
) Factory number:
Name of the manufacturer.
2 The technical delivery documents and other documents of the products shall comply with the regulations of /Z155, including: a) Product instruction manual;
5 Product contract manual and packing list,
JD/T 651, 3.i997
8.3 The products shall be packed in accordance with the provisions of J5F113. 8.4 The packaging of the products shall comply with J2? According to relevant regulations, the transportation and installation of products with a thickness of more than 8.5 mm thick must be pre-pressed and the laying of waterproof materials must comply with the relevant provisions of GB131. 8. The products should be stored in a dry, ventilated, moisture-proof and gas-free place.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.