Some standard content:
Machinery Industry Standard of the People's Republic of China
JB/T 8585
Compound Machine
1997-06-20 Issued
Ministry of Machinery Industry of the People's Republic of China
1998-81-1 Implementation
JB/T8585-1999
This standard is proposed and approved by the National Machinery Standardization Technical Committee. The original beneficiary of this standard is Shaanxi Printing Machine Factory. This standard is mainly drafted by: Ou Xiuxiu:
" Scope
Machinery Industry Standard of the People's Republic of China
Composite machine
JB/T85854997
The standard specifies the basic terms, types and state of composite machines, technical requirements, test methods, acceptance, packaging, transportation and storage.
This standard is applicable to composite machines of similar types. 2 Referenced standards
The following international standards may be included in the text, and the selected standards will become the core provisions of this standard. When this standard is mentioned, all versions are valid. It is understood that the department will obtain the approval of the standard. The parties using this standard should ensure that the following standards are not difficult to open. GE191-S0
(:FL5256-B5
GB3EE9
Packing and transportation diagram
Machine tool electrical equipment communication technology system
Transportation packaging receipt and delivery mark
GB/T 122CG-Standard
t:/T 13384
Machine product packaging communication technology position
JB 30St--- 33
ZBJ501189
3 Definition
That is, the production method of the machine is the same as the method of the machine.
3.1 Casting machine The raw material is melted into a micro-economy before the roll tube substrate is pressed and then the material is pressed and recorded.
22 The surface of the base material is made of adhesive. After being pressed with a simple sealing material and a rock, it is made into two or more types of materials. The number of layers and basic medicine are as follows: 1) the composite muscle is changed into a double-layer combination: 2) the diameter is lower than that of the current machine: 4.3 layered combination: 3) one layer and 4.3 multi-layer combination, the basic parameters are shown in Table 1. The product model name should be marked with the provisions of Bi. Approved by the Ministry of Machinery Industry on June 20, 1997, implemented on January 1, 1998, sales effect name, research on the standard, height division, NS/NWIN, State-owned Enterprises Association, material removal and thickness measurement, technical requirements, JH/18585-1997, standard type welding machine, f. 915~ c. nr, c.02~0. 6, dryness, n, no: --3. 3cs
Compound machine should comply with the correct regulations of the standard, relevant certificates and approval: the national technology has not been manufactured in the documents, the characteristics of the fish
2 are given in the cold appearance, hard calibration glue series, hot assembly total, 5. 2. 1
Effect name
But chaos 1 make a small mutual face to its target rotation axis also company medical practice
Control glue machine working rules column face point creation soft oil war light three medical station
hot one work outside the three pairs of my diameter
Each guide shaft should rotate the original station.
Table 3 Ningwei's product quality,
State effect book style
Brake separation strong bottom
Extension ink machine
Beijing extension type vertical
Ten #
Faxiang machine
JB/T858S
5.4 In the actual compound speed change range, the domestic compound machine should be stable in speed regulation, 5.5 The transmission system is stable, works normally, and has no abnormality Normal sound, 5.6 The action of the actuator is accurate, the limit environment: 5. The transmission system, electrical period heat, the rate system should have the necessary protection devices: to ensure the rate of "safety" 5. The lubrication system is controllable, the customer's adjustment point is sufficient, the yuan is paid, 5.9 The transmission shaft is not retarded, 5.10 The front piece of the movable base of the cast type machine is flexible, the stroke is large and reliable, 5.1 Electrical quality certification
5.11.1 The electrical system is neatly arranged and orderly, the system is flexible and complete, and meets the product requirements, s. J1. 2
Short-term power protection road Hengshan road (including random> money's question of his deep resistance is not polluted. External protection wire terminal equipment and other parts and the body of the complete resistance is set at 51: electrical equipment service newton with 15ccVCH electric music, the end】in series of test without breakdown and flashover phenomenon, 5.12 cold water system, gas line music system pipeline, valve seal set, water supply, gas supply with. Light connection phenomenon. 5:13
feeding, moving, receiving, room number department Adjust the material carefully, make the material stable, collect neatly, and avoid the material streaks. Extend the die head of the machine, and the machine heat report product is in accordance with the requirements of the total & complex requirements. Cut through the mechanism sound content\rate, edge this, light travel, edge science and technology to stop the Yang pass SA
5.17 External quality please
The external surface should be flat. There should be no convex disease, mutual depression, scratches, rust and other effects of the internal war rate. 5.17.2 The parts should be in color, without obvious scratches, 5.17.3 The product quality should be in accordance with the standard A 2BJ50011 environment. , 5.18 Product set
total machine production machine feeding platform document and other parts
on) plastic resignation H base second group mountain die head certificate extension type must each! :: giant compressor (machine does not include pressurized compressor; 1 replacement parts Wei Bo necessary tools and necessary spare parts, accessories: 6 test methods
6. Assembly quality control
61.1 Assembly quality inspection method see A standard metallurgy) replacement cooling light, silicon rate series or hot series assembly quality,! Plan quality should meet 5 .2.1.
6.1.2 Manually rotate the shaft and ask whether it can and report its quality 5.2.3.2 Air control special test
The product is to take the high-efficiency 50 continuous operation connection 1 out of the way, and then rotate 30r:in according to the high-speed virtual pursuit method given in the acceptance,
62.1 Technical inspection and adjustment of the air overflow situation should exist 5. No. ~ 5. 6.2.2 The output point Fu measurement to show that the degree of operation should comply with 5.5. 62.3 Dynamic extrusion Kai bar dynamic bottom inspection and stop its return swing, H visual inspection quality should be consistent. 3 Electrical quality inspection
. 3.1 The electrical system quality shall meet the requirements of 5.11.1, 5.11.2, 63.2 and 63.3 according to the specifications of 1, 1~.8 in B52268. The electrical system quality shall meet the requirements of 3.11.3~5.11. 5
JD/T85951997
4 Cooling water system is connected to tap water, and the gas system is tested by air for 5 minutes. The quality should meet the requirements of 32.6.5 Turn on the power supply of the die heater and measure the die and pyrolysis surface temperature with a point slide meter for 1 hour. A total of three points are measured, and the arithmetic average value should meet the requirements of .14
G. (Test material
For candy packaging with a width greater than or equal to 0-30g/m of the product, the product volume is continuously unloaded at a speed of 6%>. The material should meet the requirements of 5.13. 6. 7. The test method for the quality of the product is shown in the appendix. The standard is used for the detection of the error of the original degree of uniformity. The test method is shown in the appendix. The quality of the product is shown in the appendix. The standard is used for the detection of the error of the original degree of uniformity. The standard ... 06mm301
Larotten endogenous pass
+02.3mm lipid
degree t.12~G.a0mm Pp
! Cattle endogenous polymerase
Note: The test of the people's health is not carried out with the mark. 6.8 instant market test
long fast number
issued by the institute
t1e!
strictly print the most
re-report the institute
control the test party
according to the A H
and the international image
compared with the fixed point
through the production hall
products are under the state of combined pressure, and the high degree of combined tracking is carried out in the air. The ordinary advanced meter measuring machine is at night, and the stopper is 1.5m away from the height of the inquiry and 1* from the cylinder shape. The west point is measured. The average value of the air derivative is combined. Regulations, 6.9 output appearance quality specifications according to
G.9.1 day specification can product appearance and issue monitoring card, electroplating parts, its quality content to be introduced 5.17.T.5.17.2. Specification 9.2 report 25150011 regulations of hot sale 17.3.6.10 The product should be inspected according to the specifications. 5.1 The acceptance specifications should be valid. 7.1 Unit 1 calibration. 7.1.1 Each product must be inspected before it is released. If there is one item that is not specified, the product is considered unqualified. 7.1.2 Another batch of products should be inspected. 5.8 If it is unqualified, the other unit should inspect the item again. If it is still unqualified, the unit should inspect the item again. 3 Each product must be inspected by the manufacturing department before it can be released. 2 Type test. 2.1 In any of the following situations, a) a) a new product or a transferred product should be inspected. Trial formulation and appraisal of the next generation product: 4
JB/T85851997
In the above production, if there are major changes in materials, processes, and designs, which may affect product performance: when the product is discontinued for 3 years and the production is resumed, all items except 5.1U of the type test should be fully inspected. 8 Marking, packaging, storage and transportation
8.1 Each product shall be labeled with a specific part and size as specified in CB/T1830. The content shall include: a) Manufacturer name
b) Product model and name;
Main technical data:
di) Factory number:
Year and month of manufacture
8.2 Before packing, the exterior of parts and tools must be cleaned of rust preventive agent. Random parts, spare parts and maintenance tool boxes should be of selected quality and placed in appropriate positions.
8.3 The product can be packed in boxes as a whole. According to the provisions of G/T13384, the packaging box should be marked with the name of the manufacturer, the name and address of the consignee, the product model, name, serial number of the packaging box, the weight or weight of the container, the center and direction of the container, and the packaging and storage instructions should be in accordance with GB6388. 8.5 When the product is transported, it must be carefully placed according to the L mark on the outside of the packaging box to prevent it from being touched. 8.6 When the product is placed in a place with a closed system, avoid moisture when it is outside the vehicle: set a trap in the airtight compartment. The product should have the following characteristics:
)\ "Certificate of conformity: The product is produced and manufactured according to the regulations, J1/8585-1997 Appendix A (Standard Time System) Product assembly cost inspection method Assembly quality inspection method See Table A1 to determine the cooling tax of the whole company. The work of the outside people is carried out according to the requirements of the cooling tax. The work of the outside group is carried out according to the requirements of the outside group. The error may be caused by the following dangerous single or hot group. The following is not a simple test. The main position of the whole company is the total space of the whole company. The power book is JH/T 8585·-1997
Standardized test method for separation
This appendix specifies the calculation method for the separation of high-performance composite films. RI measurement
Steps of the small tensile testing machine
B2 test details
2.1 Technical Forum i.7 requires the composite test to be carried out. After the composite is normal, the composite film is cooled, one piece is used for the separation test, one piece is used for the guide test, and one piece is used for standby. 2.2 Take a sample of 22cm long and 5mm wide from a micro-channel for about 0.5 seconds and place it in a medium with a flow rate of 45~55 for 2h. B3 test sample
Pre-strip 50m along the test length: clamp the two ends into the upper and lower parts of the test machine, make the wood to the high part and the separation part of the test part! See Figure B1 and require loose kidney operation, then lift the test machine to test the angle separation at a speed of mm/mm. Remember to require arc change.
The surface structure of the two-layer material cannot be damaged after separation. The surface structure of the material can be considered to meet the standard requirements after the test.
[Lower support,
Figure BI sample center shows the empty figure
B4 Calculation of peeling strength
4.1 According to the limit of each sample, the remaining island separation of each test line is calculated according to the formula XF4.2 Calculate the peeling strength value XE of the composite film.
Number of samples;
Sample test number (1.2, 23, 4, 5) Measuring instrument
JB/T9585-1997
Appendix
(Appendix next to the actual situation)
Test method for thickness uniformity error
The measurement degree is U,o1 Thickness gauge.
C2 Measurement and calculation of thickness uniformity error, draw the thickness values of the sample from the center point to the center point and calculate the composite error value.
where the number of measuring points is
, the thickness of the first point is always straight. (3...)The product should have the following characteristics: With:
)\" Certificate:
The product is produced and manufactured in accordance with the instructions,
J1/8585-1997
Appendix A
(Standard time system)
Product assembly cost inspection method
The inspection method of the assembly cost is shown in Table A1. The whole company will determine
Cooling tax The working surface of the working group's pregnancy resistance can be measured in the second document, and some of the risk of dirty single or heat group can be measured with a relatively easy disk. The total space strength book JH/T 8585·-1997 is based on the test method for the separation degree of the shaving, and the calculation method of the high membrane blood consideration is given in this attachment. RI measurement exposure
Steps of the small tensile testing machine Www.bzxZ.net
B2 Test sample extraction
2.1 Technical Forum i.7 requires the composite test. After the composite is normal, the composite film is cooled, one piece is used for the new separation test, one piece is used for the pilot test, and one piece is used for standby. 2.2 Take a sample of 22cm long and 5mm wide from the micro-channel of about 0.5 mm, and place it in a medium with a flow rate of 45~55 for 2h. B3 Test of the sample
Pre-peel 50m along the test length: clamp the two pieces into the upper and lower parts of the test machine, and make the wood high and the separation part of the judgment part! See Figure B1 and the fee is required to loosen the kidney, and then lift the test machine to test the angle separation at a speed of mm/mm. Remember to change the arc.
The surface structure of the two-layer material cannot be damaged after separation. The surface structure of the material can be considered to meet the standard requirements after the test.
[Lower support,
Figure BI sample center shows the empty figure
B4 Calculation of peeling strength
4.1 According to the limit of each sample, the remaining island separation of each test line is calculated according to the formula XF4.2 Calculate the peeling strength value XE of the composite film.
Number of samples;
Sample test number (1.2, 23, 4, 5) Measuring instrument
JB/T9585-1997
Appendix
(Appendix next to the actual situation)
Test method for thickness uniformity error
The measurement degree is U,o1 Thickness gauge.
C2 Measurement and calculation of thickness uniformity error, draw the thickness values of the sample from the center point to the center point and calculate the composite error value.
where the number of measuring points is
, the thickness of the first point is always straight. (3...)The product should have the following characteristics: With:
)\" Certificate:
The product is produced and manufactured in accordance with the instructions,
J1/8585-1997
Appendix A
(Standard time system)
Product assembly cost inspection method
The inspection method of the assembly cost is shown in Table A1. The whole company will determine
Cooling tax The working surface of the working group's pregnancy resistance can be measured in the second document, and some of the risk of dirty single or heat group can be measured with a relatively easy disk. The total space strength book JH/T 8585·-1997 is based on the test method for the separation degree of the shaving, and the calculation method of the high membrane blood consideration is given in this attachment. RI measurement exposure
Steps of the small tensile testing machine
B2 Test sample extraction
2.1 Technical Forum i.7 requires the composite test. After the composite is normal, the composite film is cooled, one piece is used for the new separation test, one piece is used for the pilot test, and one piece is used for standby. 2.2 Take a sample of 22cm long and 5mm wide from the micro-channel of about 0.5 mm, and place it in a medium with a flow rate of 45~55 for 2h. B3 Test of the sample
Pre-peel 50m along the test length: clamp the two pieces into the upper and lower parts of the test machine, and make the wood high and the separation part of the judgment part! See Figure B1 and the fee is required to loosen the kidney, and then lift the test machine to test the angle separation at a speed of mm/mm. Remember to change the arc.
The surface structure of the two-layer material cannot be damaged after separation. The surface structure of the material can be considered to meet the standard requirements after the test.
[Lower support,
Figure BI sample center shows the empty figure
B4 Calculation of peeling strength
4.1 According to the limit of each sample, the remaining island separation of each test line is calculated according to the formula XF4.2 Calculate the peeling strength value XE of the composite film.
Number of samples;
Sample test number (1.2, 23, 4, 5) Measuring instrument
JB/T9585-1997
Appendix
(Appendix next to the actual situation)
Test method for thickness uniformity error
The measurement degree is U,o1 Thickness gauge.
C2 Measurement and calculation of thickness uniformity error, draw the thickness values of the sample from the center point to the center point and calculate the composite error value.
where the number of measuring points is
, the thickness of the first point is usually straight. (3...)
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.