JB/T 10211-2000 This standard specifies the type and size, technical requirements, test methods, inspection rules, marking, packaging and storage of single-piece carbide finger-jointed woodworking milling cutters. This standard was first issued in August 2000. JB/T 10211-2000 Single-piece carbide finger-jointed woodworking milling cutters JB/T10211-2000 Standard download decompression password: www.bzxz.net

IC$ 24.120.20
Machinery Industry Standard of the People's Republic of China
JB/T10211-2000
Single blade carbid finger joint cutt for woodworking2000-08-31 Issued
National Bureau of Machinery Industry
2001-01-01 Implementation
JB/T10211-2000
Appendix A of this standard is the standard annex.
This standard is proposed and managed by the National Standardization Technical Committee for Machine Tools and Cutting Tools. The responsible drafting unit of this standard: Kunming Kangfa Machinery Co., Ltd. The main drafters of this standard: Zhao Xiaochuan, Heng Dianxuan, Xu Guanggun, Zheng Anjian. Scope
Machinery Industry Standard of the People's Republic of China
Hydraulic Hard Alloy Single-piece Finger Joint Milling Cutter
Sigleblade Earbid Finger Jointcutt for WoodworklngJB 1021t—2000
This standard specifies the type and size, technical requirements, test conditions, inspection rules and markings of 1-metal alloy single-piece finger joint milling cutter (hereinafter referred to as finger joint cutter), including length and storage. 2 Referenced Standards
The texts contained in the listed standards constitute the provisions of this standard through reference in the wood standard: When this standard is published, the versions shown are valid. All standards are subject to revision, and the parties using this standard should explore the possibility of using the following standards to create new versions. GB/T 6991999
GB1031—1995
B12557—2000
JB 6113—1992
Y$F]' 490--1994
3 Types and dimensions
High-quality carbon cable structural steel
Surface finishing parameters and force valueswwW.bzxz.Net
General safety rules for woodworking machine tools
Safety technical conditions for cutting tools used in this machine
Hard alloy grades
31 Difficult type gauge according to wind 1 and table! Regulations: 1
National Machinery Industry Bureau 2000-09-31 approved 2001-01-01 implementation
Book size
3.2 Marking example
Light limit deviation
Basic technical size
10211-2000
Table of connecting knife size
Maximum profit control
± 0 025
Outer diameter 160mm; thickness 4mm, aperture 70mm, two teeth for the finger joint knife, marked as: too "confirmed to meet the box single piece finger and sharp condition 160×4×70-2JB/T[02]! 20004 Technical requirements
4.! The finger joint is not allowed to have cracks, spots, corrosion, abrasion and other defects that affect the performance. 4.2 The surface roughness of the finger joint knife is in accordance with the provisions of GA/T1131. The maximum allowable value meets the following requirements: a) The front is _0.4μ㎡
b) The blade surface and the back are R0.8m.
c) The ratio of the aperture surface and the two supporting end faces is 1.25=m. 43 The position of the finger joint is as specified in Table 2. Table 2 The position of the finger joint is as follows:
The radial load of the blade of the finger joint to the hole diameter axis and the symmetry of the center plane of the body thickness of the two joints Note: The radial load of the blade of the finger joint to the hole diameter axis and the symmetry of the two joints to ... 4.4 The cutting part of the finger joint is made of YG8 in accordance with YS/400 or other hard metal with material performance not lower than 11. The material of the finger joint is made of 45 steel in accordance with GB/T699 or other materials with material performance not lower than 4. The finger joint should be statically balanced, and the maximum allowable unbalance is 80, mm, 4.6 The shear strength of the finger joint The speed should not be lower than 120MPa. 4.7 The maximum working speed of the finger joint knife should be marked, and the maximum working speed is 7000r/mjm. 4.8 The safety of the finger joint knife should also comply with the relevant provisions of B6113. 5 Test methods and inspection rules
5.1 The performance test of the finger joint knife should be carried out on the machine with the standard of comfort accuracy, and all safety requirements shall be determined in accordance with GR1255. 5.2 The test material is a medium-hard seat material with a water content of 12%~15%. 5.3 The test cutting agent specification is in accordance with Table 3.
Outer diameter of finger joint
J8/T102E1-200
Special speed of finger joint||tt| |Test cutting specification
Feed speed
5.4 After the test, the joints are not allowed to have blunt edges and obvious wear, and can continue to be used. 6 Marking, packaging and storage
1 Finger jointing knives should be marked with: trademark, specification and maximum operating speed. 6.2 Finger jointing knives should be marked with: product name, standard number, manufacturer name, factory address and trademark, specifications, location and production date. 6 Finger jointing knives should be marked with: product name, size, gross weight and operation marks such as "afraid of moisture" and "caution" before packaging. Finger joints should be treated with anti-corrosion before packaging, and should not rust within half a year from the production date. 6. The packaging tray should be accompanied by a certificate of conformity.
6.6 Finger joints should be stored in a well-arranged warehouse without corrosive media. JB/T 10211-2000
Collection A
(Appendix to the standard)
Test method for position tolerance of finger joints of single piece of hardwood woodworking A1. Test method for position tolerance of finger joints of single piece of hardwood woodworking alloy is shown in Table A1. Table A1
According to the item
Tolerance of finger joints
Tolerance of finger joints
Tolerance of finger joints
Tolerance of support faces
Tolerance of hole diameter ... |tt||Parallelism inspection method of supporting end
Put the finger joint on the circular motion, press it with a
flange, put the dial indicator contact heavily against the top edge of the knife tooth, and the finger edge rotates one circle. The maximum and minimum values ​​of the radial direction of the finger joint are restored by percentage.
The surface of the dial indicator is in the force tooth
. , the finger connection is able to turn - feel, read the stop
dial indicator value; since the height is not
, use the same method to measure the knife teeth on the other side
the same position full of the dial indicator value, the difference between the maximum value and the minimum value of the two dial indicators refers to the symmetry of the blade
. Place the dial indicator contact vertically on the central part of a supporting surface of the finger
door, and use the finger to hang the knife and turn it. The whole of the maximum value and the minimum value read on the dial indicator is the method of inspection for the surface of the plate, which belongs to the anti-movement
super violation. ||The supporting belt of the joint shall be square,
the horizontal effect shall be in the flat surface.
the lead head of the dial gauge shall be against the support surface 1 of the finger joint knife,
measure the dosage in two perpendicular directions, the difference between the maximum and minimum number of teeth of the dial gauge is the parallelism of the finger joint knife
test force clear business drawing
standard monitoring tool
0.0%
dividing indicator
wind moving position
pressure flange
0.1 to degree first dial gauge
assembly frame
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.