Some standard content:
ICS 55. 140
National Standard of the People's Republic of China
GB/T13252-—2008
Replaces GB13252--2CC3
Packaging containers
Steel pails
Packing comtainers--Sicer naisPublished on 2008-07-18
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of ChinaStandardization Administration of the People's Republic of China
Implementation on 2009-01-01
This standard adopts and amends Japanese Industrial Standard JIS162℃1995 "Steel pails". Compared with JIS Z1520-1995, this standard has the following main differences: the applicable scope of volume is expanded to 17~241.
the classification by steel plate thickness is cancelled;
- there are differences in external dimensions:
- ... increase the hair of coating adhesion;
the liquid resistance of steel pails for non-dangerous goods packaging is subject to the most stringent requirements and no longer classified regulations; the pile load is stipulated as 1250N
product identification is stipulated in accordance with domestic requirements:
·: some formatting formats and expressions have been modified according to Chinese habits. This standard replaces GB13252-2003 "Packaging Container Steel Pails" This standard has the following main changes compared with (G1313252-2003: "Steel pail classification Non-dangerous goods packaging has been added to the category, and notes have been added to Table 1; some dimensions have been revised;
.-.. Airtightness test: 3.1 Class I barrel test pressure is changed to 30kPa; GB/T13252--2008
-- Hydraulic test: 3.4 Class I barrel test pressure is changed to 250kPa, 3.1 Class I barrel test pressure is 100kPa; Drop height: I, III, III drop height are changed to 1.8m, 1.2m, 18m respectively, non-dangerous goods packaging is 0.8m, ring strength: test force is changed to 6(0)N. This standard is proposed and approved by the National Packaging Standardization Technical Committee. The responsible drafting unit of this standard: National Packaging Product Quality Supervision and Inspection Center (Guangzhou): The drafting units of this standard booth are: Wanchengjin Packaging Co., Ltd., Shunde District, Foshan City, China Chemical Industry Standardization Institute, Jiangsu Product Quality Supervision and Inspection Institute.
The main drafters of this standard are: Cai Yijun, Mi Liping, Lu Ming, Ling Guangyao, Liang Juncheng, Mei Chu, Gao Meiwu, Gong Fengling. The previous versions of the standards interpreted by this standard booth are: G1313252-1991GB13252-2003.
1 Fanshu
Packaging containers
GB/T13252-2008
This standard specifies the classification technical requirements, test methods and specifications of steel buckets (hereinafter referred to as buckets) with a capacity of 17L to 24L for the transportation and storage of liquid and liquid dangerous goods and non-dangerous goods. Methods, inspection rules, marking, transportation and storage. This standard applies to steel buckets made of thin steel plates as the main material. The clauses in the normative reference documents become the clauses of this standard through reference in this standard. For any dated reference document, all subsequent amendments (excluding errata) or revisions are not applicable to this standard. However, the parties to the agreement based on this standard are encouraged to study whether the latest versions of these documents can be used. For any unexpired reference document, its latest version shall be used in this standard. GB/T1720 Determination of the strength of film steel
GB/T2828.1 Counting sample inspection procedure Part 1: Sampling plan for batch inspection at acceptance quality limit (AQL) (GB/T 2828. 1---2003, ISO 2859-1:1999, ID1) (GI3/T4857.3 Packaging and transport packages Part 3: Static load stacking test method GB3/T4857.5 Packaging and transport packages Drop test method (GI3/T4851.5-1992.idt2248:1985) GB/T13040 Packaging terminology Metal container
G13/T17344 Packaging Packaging container airtightness test method 3 Definitions, symbols and codes
3.1 Terms and definitions
The terms and definitions established in GB/T1304C apply to this standard. 3.2 Symbols
) Inner diameter;
H: -Inner quotient;
H. Outer height.
3.3 Code
T—barrel, with scale;
S—barrel, without scale;
4 Bucket classification
4.1 Buckets are divided into T-type and S-type according to their appearance. They are also divided into 1 category and 4 specifications, see 1, 1
GB/T 13252--2008
Not applicable to S-type
Nominal volume
Table 1 Bucket categories and specifications
4.2 Buckets are divided into dangerous goods packaging class I, II, III and non-dangerous goods packaging according to technical requirements. 5 Structural dimensions
5.1 Structural dimensions and drawings of T-type barrels
5. 1. 1T-type barrel structural dimensions are shown in Table 2.
The claw cover type, with a claw that can be used to tighten the cover
on the body
tight cover type, through the hoop to tighten the cover
fixed type, barrel cover and barrel bottom
through the curling state to determine the body
Inner dimensions do not include gaskets,
b does not include the fourth specification.
: does not include the third and fourth specifications.
5.1.2 The first type of T-type barrel diagram is shown in Figure 1.
Table 2 T-type barrel dimensions
D:
Limit deviation
A few products
5. 1. 3 The second type of T-type barrel diagram is shown in Figure 2. Figure 2
5. 1. 4 Type 3 T-type barrels See 3.3.1 General limits GB/T 13252--2008 Units are in meters Limit deviation GB/T 13252--2008 5.2 S-type barrels Structural dimensions and drawings 5.2. 1 Structural dimensions of the first and second types of barrels are shown in Table 3 and Figure 3. Dimensions of the first and second types of S-type barrels. 5.2.2 S-type barrels of the first type, Figure 4. 5.2.3 S-type barrels of the second type, Figure 5. Inner diameter D. Limit difference. Inner height H. Unit is meter. 5.2.4 Structural dimensions of the third type of S-type barrels are shown in Table 4 and Figure 6. Figure 5. Table 4 Dimensions of the third type of S-type barrels. 5.2.5 The structural dimensions of the first type S-type barrel are shown in Table 5. Figure 751. Inner height H, Table 5. Dimensions of the fourth type S-type barrel. Limit deviation. Inner height H. Extreme deviation. GB/T13252--2008. Unit is meter. External height Ha. Limit deviation. GB/T 13252—2008
6 Materials and accessories
6.1 The performance indicators of steel plates and steel wires shall comply with the provisions of relevant national standards. 6.2 The sealing fillers for buckets shall be made of materials with good sealing performance and suitable for the contents. 6.3 The paint for buckets shall be made of materials with strong adhesion and good weather resistance. The inner wall paint shall be made of materials corresponding to the contents of the bucket. When directly in contact with food, medicine and food additives, the inner wall of the bucket shall comply with the provisions of relevant health standards. 7 Requirements
7.1 Basic requirements
7.1.1 Appearance requirements
The inner and outer surfaces of the bucket are smooth and neat, without obvious pits and rust. The curling edges are uniform, without wrinkles, thorns and iron tongues. The seams are flat and uniform, without olefin nodules. The coating color is uniform, without obvious defects such as discoloration, sagging, blistering and scratches. 7.1.2 Barrel body type
For barrels of type 1 and 2, there should be a ring rib for crowning. For barrels of type 3 and 4, whether to have a ring rib is determined by both parties.
7.1.3 Size requirements
The size of the barrel should comply with the provisions of Chapter 5. Special specifications shall be determined by both parties. 7.1.4 Hygiene requirements
Barrels used for food, medicine and food additives shall comply with the Food Hygiene Law and relevant standards and regulations. 7.2 Performance requirements
7.2.1 Airtight performance
After the airtight test, the barrel should not leak. 7.2.2 Hydraulic performance
After the hydraulic test, the 3.1-class barrels for corrugated packaging shall not leak. 7.2.3 Drop resistance
After the drop test, the barrel shall not leak.
7.2.4 Stacking resistance
After the stacking test, the barrel shall not leak or deform, which may affect the transportation safety. 7.2.5 Strength of handles and handle rings
After the J&S test, the handles, handle rings and handles shall not break or be damaged. 7.2.6 Coating adhesion
The coating adhesion shall be better than Class 2.
8 Test method
Appearance, type, size
The appearance quality and barrel body type shall be checked by daily measurement. The universal or special ruler can be used for testing. 8.2 Air tightness test GB/T13252-2008 The air tightness test shall be carried out in accordance with G/T17344. The test pressures for dangerous goods packaging and non-dangerous goods packaging are shown in Table 6 and Table 7 respectively. Table 6 Test pressure for dangerous goods packaging with buckets Test pressure method / kPz Test method / 8.3 Hydraulic test Before adding benefits After adding benefits Hazard level I package condensation Table? Pressure test of buckets for non-hazardous goods packaging Category 1
This test is not carried out for buckets of category 1 and 2 Category 2
Hazard level II, packaging
For buckets of category 3 and 1, make a hole in oval 1, fill the bucket with water, connect the pressure gauge with the pressure recorder, and fix them on the through-hole through the connecting piece, start the pump to pressurize the bucket, close the valve after reaching the test pressure, maintain the pressure at 5min, the test pressure is shown in Table 8, and check whether the bucket is leaking.
Carbon 8 Test pressure
Test pressure/ka
8.4 Drop test
Danger level Packaging
Danger level III and non-dangerous goods packaging 100
(3/T4857.5) Drop each product once to check for leakage. Contents and filling amount, drop location see Table 9, drop height see Table 1C, when filled When the density of the liquid is greater than 1.2g/cm2, the drop height is shown in Table 11.9 Contents and filling amount, drop position
Internal contents
Drop separation /I
Dew height /m
Mold contents
Dry sand
Energy-saving packaging
95% of the penetration
8% of the capacity
Table 10 Drop Height
Dangerous grade packaging
Falling position
Welded chain, bottom, hoop edge and seam joints Dangerous level and card Dangerous goods packaging
Falling height (when the density of the liquid is greater than 1.2g/cm2) Dangerous level packaging
Liquid density × 1.5
Dangerous grade packaging
Overall density × 1.2
Dangerous grade III non-hazardous goods packaging
Liquid density × 0.
After the 3rd and 4th category buckets fall, a small hole is made at the appropriate position of the lifting platform to balance the internal and external pressures, and check for leakage within 5 minutes. 8.5 Stacking test
According to the provisions of GB/T4857.3, the calcium push test time is 24h, and the stack load is: 12FCN. 7
GB/T 13252--2008
8.6 Handle and handle strength test
Fix the handle or handle with an appropriate method, then add a load of 600N vertically on the barrel body. After 5 minutes, check whether the handle, ring and connecting part are broken or damaged. 8.7 Determination of coating adhesion
Inspect in accordance with the provisions of C:B/T 1720. 9 Inspection rules
9.1 Handle inspection is divided into factory inspection and type inspection: 9.1.1 Factory inspection
9.1.1.17.1.1, 7.1.2, 7.1.3 and 7.2.1 are the inspection items. According to GB/T2828.1, the normal inspection is carried out once. 9.1.1.27.1.1, 7.1.2, 7.1.3 are the special inspection levels. S-3, acceptance quality limit is G. 1i, sampling number and qualified judgment number are shown in Table 12,
Table 12 Sampling number and qualified judgment number
Extended·second sampling
Batch range
5C1--3 200
3 201---35 000
35 001-~500 000
500001
Inspection level is S-3
Number of samples
Acceptance quality limit (AQI) is 6.5
Qualified judgment number
Unqualified judgment number
9. 1. 1. 37. 2.1 The inspection water is special inspection water S-1, and the acceptance quality limit is 2. 5. Sampling number and qualified judgment number Table 13. Table 13 Sampling number and qualified judgment number
Normal -1 batch
Batch range
501~-35 000
35 col
Plastic inspection
9. 1. 2. 1
Inspection level is S-1
Subject
When any of the following situations occurs, type inspection should be carried out: trial production and type identification of new products or conversion of old products; when there are changes in structure, materials and process that may affect product performance; during normal production, an inspection is carried out every six months; when the product is resumed after a long period of suspension;
When the inspection result is significantly different from the previous type inspection result; when the national quality supervision agency proposes the requirement for type inspection. The acceptance quality limit (AQL) is 2.5
Number of qualified determination
Items 7. and 7.2 of this standard are type inspection items, and the number of samples is 5. The inspection procedure is as follows: 9.1.2.2
Number of unqualified items
Take 3 sample barrels to inspect item 7.1, then use these 3 sample barrels for airtightness test, and then use these 3 sample barrels for hydraulic pressure test;
GR/T 13252-2008
b) Take 3 sample barrels from the remaining 5 sample barrels for compression test, and then use these 6 sample barrels for drop test. 9.2 Rules
9.2.1 Inspection
9.2.1.1 If there are two or more unqualified items in item 7.1, the sample is judged to be unqualified. If item 7.2.1 is unqualified, the sample is judged to be unqualified.
9.2.1.2 When the number of unqualified samples is greater than or equal to the number of unqualified judgments specified in Tables 12 and 13, the batch of products shall be deemed unqualified. 9.2.2 Type inspection
9.2.2.1 If two or more items in .1 are unqualified, the sample shall be deemed unqualified. If 1 sample is unqualified, the batch shall be deemed unqualified.
9.2.2.2 Inspect item by item according to 7.2 of this standard. If one item is unqualified, the sample shall be deemed unqualified. If 1 sample is unqualified, the batch shall be deemed unqualified:
Marking, transportation and storage
The manufacturer's mark or code shall be on the baggage.
The transported dog storage should be protected from rain, sun, moisture, pollution and deformation, etc. 9
GB/T13252-2008
Chinese Standards
Packing container
Steel bucket
GB/T 13252-2C08
Published and distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal code: 109C45
Website spc.net.cn
Tel: 6852394658517548
China Standards Press Taizhuodao Post Office Printing Name Assisted Xinhua Bookstore
Book 880×1230 -/16
Qiu Zhang 1
Mathematics 19,000 words
November 2008 edition November 2008 first printing number: 155065: 1-33939
If there is any printing error, the publishing center of our company will replace the version. Double exclusive infringement will be investigated
Report phone: (010) 685335336 Coating Adhesion
Coating Adhesion should be better than Grade 2.
8 Test Method
Appearance, Type, Dimension
Appearance quality and barrel type shall be checked by daily measurement. The universal or special ruler can be used for measurement. 8.2 Airtightness Test
GB/T13252—2008
The airtightness test shall be carried out in accordance with G/T17344. The test pressures for dangerous goods packaging and non-dangerous goods packaging are shown in Table 6 and Table 7 respectively. Table 6 Test Pressure for Dangerous Goods Packaging Buckets
Test Method/kPz
Test Method/
8.3 Hydraulic Test
Before Addition
After Addition
Hazard Level I Packaging
Table? Pressure test of buckets for non-hazardous goods packaging Category 1
This test is not carried out for buckets of category 1 and 2 Category 2
Hazard level II, packaging
For buckets of category 3 and 1, make a hole in oval 1, fill the bucket with water, connect the pressure gauge with the pressure recorder, and fix them on the through-hole through the connecting piece, start the pump to pressurize the bucket, close the valve after reaching the test pressure, maintain the pressure at 5min, the test pressure is shown in Table 8, and check whether the bucket is leaking.
Carbon 8 Test pressure
Test pressure/ka
8.4 Drop test
Danger level Packaging
Danger level III and non-dangerous goods packaging 100
(3/T4857.5) Drop each product once to check for leakage. Contents and filling amount, drop location see Table 9, drop height see Table 1C, when filled When the density of the liquid is greater than 1.2g/cm2, the drop height is shown in Table 11.9 Contents and filling amount, drop position
Internal contents
Drop separation /I
Dew height /m
Mold contents
Dry sand
Energy-saving packaging
95% of the penetration
8% of the capacity
Table 10 Drop Height
Dangerous grade packaging
Falling position
Welded chain, bottom, hoop edge and seam joints Dangerous level and card Dangerous goods packaging
Falling height (when the density of the liquid is greater than 1.2g/cm2) Dangerous level packaging
Liquid density × 1.5
Dangerous grade packaging
Overall density × 1.2
Dangerous grade III non-hazardous goods packaging
Liquid density × 0.
After the 3rd and 4th category buckets fall, a small hole is made at the appropriate position of the lifting platform to balance the internal and external pressures, and check for leakage within 5 minutes. 8.5 Stacking test
According to the provisions of GB/T4857.3, the calcium push test time is 24h, and the stack load is: 12FCN. 7
GB/T 13252--2008
8.6 Handle and handle strength test
Fix the handle or handle with an appropriate method, then add a load of 600N vertically on the barrel body. After 5 minutes, check whether the handle, ring and connecting part are broken or damaged. 8.7 Determination of coating adhesion
Inspect in accordance with the provisions of C:B/T 1720. 9 Inspection rules
9.1 Handle inspection is divided into factory inspection and type inspection: 9.1.1 Factory inspection
9.1.1.17.1.1, 7.1.2, 7.1.3 and 7.2.1 are the inspection items. According to GB/T2828.1, the normal inspection is carried out once. 9.1.1.27.1.1, 7.1.2, 7.1.3 are the special inspection levels. S-3, acceptance quality limit is G. 1i, sampling number and qualified judgment number are shown in Table 12,
Table 12 Sampling number and qualified judgment number
Extended·second sampling
Batch range
5C1--3 200
3 201---35 000
35 001-~500 000
500001
Inspection level is S-3
Number of samples
Acceptance quality limit (AQI) is 6.5
Qualified judgment number
Unqualified judgment number
9. 1. 1. 37. 2.1 The inspection water is special inspection water S-1, and the acceptance quality limit is 2. 5. Sampling number and qualified judgment number Table 13. Table 13 Sampling number and qualified judgment number
Normal -1 batch
Batch range
501~-35 000
35 col
Plastic inspection
9. 1. 2. 1
Inspection level is S-1
Subject
When any of the following situations occurs, type inspection should be carried out: trial production and type identification of new products or conversion of old products; when there are changes in structure, materials and process that may affect product performance; during normal production, an inspection is carried out every six months; when the product is resumed after a long period of suspension;
When the inspection result is significantly different from the previous type inspection result; when the national quality supervision agency proposes the requirement for type inspection. The acceptance quality limit (AQL) is 2.5
Number of qualified determination
Items 7. and 7.2 of this standard are type inspection items, and the number of samples is 5. The inspection procedure is as follows: 9.1.2.2
Number of unqualified items
Take 3 sample barrels to inspect item 7.1, then use these 3 sample barrels for airtightness test, and then use these 3 sample barrels for hydraulic pressure test;
GR/T 13252-2008
b) Take 3 sample barrels from the remaining 5 sample barrels for compression test, and then use these 6 sample barrels for drop test. 9.2 Rules
9.2.1 Inspection
9.2.1.1 If there are two or more unqualified items in item 7.1, the sample is judged to be unqualified. If item 7.2.1 is unqualified, the sample is judged to be unqualified.
9.2.1.2 When the number of unqualified samples is greater than or equal to the number of unqualified judgments specified in Tables 12 and 13, the batch of products shall be deemed unqualified. 9.2.2 Type inspection
9.2.2.1 If two or more items in .1 are unqualified, the sample shall be deemed unqualified. If 1 sample is unqualified, the batch shall be deemed unqualified.
9.2.2.2 Inspect item by item according to 7.2 of this standard. If one item is unqualified, the sample shall be deemed unqualified. If 1 sample is unqualified, the batch shall be deemed unqualified:
Marking, transportation and storage
The manufacturer's mark or code shall be on the baggage.
The transported dog storage should be protected from rain, sun, moisture, pollution and deformation, etc. 9
GB/T13252-2008
Chinese Standards
Packing container
Steel bucket
GB/T 13252-2C08
Published and distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal code: 109C45
Website spc.net.cn
Tel: 6852394658517548
China Standards Press Taizhuodao Post Office Printing Name Assisted Xinhua Bookstore
Book 880×1230 -/16
Qiu Zhang 1
Mathematics 19,000 words
November 2008 edition November 2008 first printing number: 155065: 1-33939
If there is any printing error, the publishing center of our company will replace the version. Double exclusive infringement will be investigated
Report phone: (010) 685335336 Coating Adhesion
Coating Adhesion should be better than Grade 2.
8 Test Method
Appearance, Type, Dimension
Appearance quality and barrel type shall be checked by daily measurement. The universal or special ruler can be used for measurement. 8.2 Airtightness Test
GB/T13252—2008
The airtightness test shall be carried out in accordance with G/T17344. The test pressures for dangerous goods packaging and non-dangerous goods packaging are shown in Table 6 and Table 7 respectively. Table 6 Test Pressure for Dangerous Goods Packaging Buckets
Test Method/kPz
Test Method/
8.3 Hydraulic Test
Before Addition
After Addition
Hazard Level I Packaging
Table? Pressure test of buckets for non-hazardous goods packaging Category 1
This test is not carried out for buckets of category 1 and 2 Category 2
Hazard level II, packaging
For buckets of category 3 and 1, make a hole in oval 1, fill the bucket with water, connect the pressure gauge with the pressure recorder, and fix them on the through-hole through the connecting piece, start the pump to pressurize the bucket, close the valve after reaching the test pressure, maintain the pressure at 5min, the test pressure is shown in Table 8, and check whether the bucket is leaking.
Carbon 8 Test pressure
Test pressure/ka
8.4 Drop test
Danger level Packaging
Danger level III and non-dangerous goods packaging 100
(3/T4857.5) Drop each product once to check for leakage. Contents and filling amount, drop location see Table 9, drop height see Table 1C, when filled When the density of the liquid is greater than 1.2g/cm2, the drop height is shown in Table 11.9 Contents and filling amount, drop position
Internal contents
Drop separation /I
Dew height /m
Mold contents
Dry sand
Energy-saving packaging
95% of the penetration
8% of the capacity
Table 10 Drop Height
Dangerous grade packaging
Falling position
Welded chain, bottom, hoop edge and seam joints Dangerous level and card Dangerous goods packaging
Falling height (when the density of the liquid is greater than 1.2g/cm2) Dangerous level packaging
Liquid density × 1.5
Dangerous grade packaging
Overall density × 1.2
Dangerous grade III non-hazardous goods packaging
Liquid density × 0.
After the 3rd and 4th category buckets fall, a small hole is made at the appropriate position of the lifting platform to balance the internal and external pressures, and check for leakage within 5 minutes. 8.5 Stacking test
According to the provisions of GB/T4857.3, the calcium push test time is 24h, and the stack load is: 12FCN. 7
GB/T 13252--2008
8.6 Handle and handle strength test
Fix the handle or handle with an appropriate method, then add a load of 600N vertically on the barrel body. After 5 minutes, check whether the handle, ring and connecting part are broken or damaged. 8.7 Determination of coating adhesion
Inspect in accordance with the provisions of C:B/T 1720. 9 Inspection rules
9.1 Handle inspection is divided into factory inspection and type inspection: 9.1.1 Factory inspection
9.1.1.17.1.1, 7.1.2, 7.1.3 and 7.2.1 are the inspection items. According to GB/T2828.1, the normal inspection is carried out once. 9.1.1.27.1.1, 7.1.2, 7.1.3 are the special inspection levels. S-3, acceptance quality limit is G. 1i, sampling number and qualified judgment number are shown in Table 12,
Table 12 Sampling number and qualified judgment number
Extended·second sampling
Batch range
5C1--3 200
3 201---35 000
35 001-~500 000
500001
Inspection level is S-3
Number of samples
Acceptance quality limit (AQI) is 6.5
Qualified judgment number
Unqualified judgment number
9. 1. 1. 37. 2.1 The inspection water is special inspection water S-1, and the acceptance quality limit is 2. 5. Sampling number and qualified judgment number Table 13. Table 13 Sampling number and qualified judgment number
Normal -1 batch
Batch range
501~-35 000
35 col
Plastic inspection
9. 1. 2. 1
Inspection level is S-1
Subject
When any of the following situations occurs, type inspection should be carried out: trial production and type identification of new products or conversion of old products; when there are changes in structure, materials and process that may affect product performance; during normal production, an inspection is carried out every six months; when the product is resumed after a long period of suspension;
When the inspection result is significantly different from the previous type inspection result; when the national quality supervision agency proposes the requirement for type inspection. The acceptance quality limit (AQL) is 2.5
Number of qualified determination
Items 7. and 7.2 of this standard are type inspection items, and the number of samples is 5. The inspection procedure is as follows: 9.1.2.2
Number of unqualified items
Take 3 sample barrels to inspect item 7.1, then use these 3 sample barrels for airtightness test, and then use these 3 sample barrels for hydraulic pressure test;
GR/T 13252-2008
b) Take 3 sample barrels from the remaining 5 sample barrels for compression test, and then use these 6 sample barrels for drop test. 9.2 Rules
9.2.1 Inspection
9.2.1.1 If there are two or more unqualified items in item 7.1, the sample is judged to be unqualified. If item 7.2.1 is unqualified, the sample is judged to be unqualified.
9.2.1.2 When the number of unqualified samples is greater than or equal to the number of unqualified judgments specified in Tables 12 and 13, the batch of products shall be deemed unqualified. 9.2.2 Type inspection
9.2.2.1 If two or more items in .1 are unqualified, the sample shall be deemed unqualified. If 1 sample is unqualified, the batch shall be deemed unqualified.
9.2.2.2 Inspect item by item according to 7.2 of this standard. If one item is unqualified, the sample shall be deemed unqualified. If 1 sample is unqualified, the batch shall be deemed unqualified:
Marking, transportation and storage
The manufacturer's mark or code shall be on the baggage.
The transported dog storage should be protected from rain, sun, moisture, pollution and deformation, etc. 9
GB/T13252-2008
Chinese Standards
Packing container
Steel bucket
GB/T 13252-2C08
Published and distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal code: 109C45
Website spc.net.cn
Tel: 6852394658517548
China Standards Press Taizhuodao Post Office Printing Name Assisted Xinhua Bookstore
Book 880×1230 -/16
Qiu Zhang 1
Mathematics 19,000 words
November 2008 edition November 2008 first printing number: 155065: 1-33939
If there is any printing error, the publishing center of our company will replace the version. Double exclusive infringement will be investigated
Report phone: (010) 685335334 Drop test
Danger level packaging
Danger level III and non-dangerous goods packaging 100
(3/T4857.5) will drop each product once to check for leakage. Contents and filling amount, drop location see Table 9, drop height see Table 1C, when the density of the liquid is greater than 1.2g/cm3, drop height see Table 11.9 Contents and filling amount, drop location
International Contents
Dropping degree/I
Exposure height/m
Mold Contents
For dry sand
Danger level packaging
95% of the penetration area
8% of the capacity
Table 10 Drop height
Dangerous packaging | |tt||Falling part
Welded chain, bottom, hoop edge and seam joint parts Hazard level and card Hazardous goods packaging
Falling height (when the density of the liquid is greater than 1.2g/cm2) Hazard level packaging
Liquid density × 1.5
Hazardous level packaging
Overall density × 1.2
Hazard level III non-hazardous goods packaging
Liquid density × 0.
After the 3rd and 4th category buckets fall, a small hole is made at the appropriate part of the lifting platform to balance the internal and external pressures, and check for leakage within 5 minutes. 8.5 Stacking test
According to the provisions of GB/T4857.3, the calcium push test time is 24h, and the stack load is: 12FCN. 7
GB/T 13252--2008
8.6 Handle and handle strength test
Fix the handle or handle with an appropriate method, then add a load of 600N vertically on the barrel body. After 5 minutes, check whether the handle, ring and connecting part are broken or damaged. 8.7 Determination of coating adhesion
Inspect in accordance with the provisions of C:B/T 1720. 9 Inspection rules
9.1 Handle inspection is divided into factory inspection and type inspection: 9.1.1 Factory inspection
9.1.1.17.1.1, 7.1.2, 7.1.3 and 7.2.1 are the inspection items. According to GB/T2828.1, the normal inspection is carried out once. 9.1.1.27.1.1, 7.1.2, 7.1.3 are the special inspection levels. S-3, acceptance quality limit is G. 1i, sampling number and qualified judgment number are shown in Table 12,
Table 12 Sampling number and qualified judgment number
Extended·second sampling
Batch range
5C1--3 200
3 201---35 000
35 001-~500 000
500001
Inspection level is S-3
Number of samples
Acceptance quality limit (AQI) is 6.5
Qualified judgment number
Unqualified judgment number
9. 1. 1. 37. 2.1 The inspection water is special inspection water S-1, and the acceptance quality limit is 2. 5. Sampling number and qualified judgment number Table 13. Table 13 Sampling number and qualified judgment number
Normal -1 batch
Batch range
501~-35 000
35 col
Plastic inspection
9. 1. 2. 1
Inspection level is S-1
Subject
When any of the following situations occurs, type inspection should be carried out: trial production and type identification of new products or conversion of old products; when there are changes in structure, materials and process that may affect product performance; during normal production, an inspection is carried out every six months; when the product is resumed after a long period of suspension;
When the inspection result is significantly different from the previous type inspection result; when the national quality supervision agency proposes the requirement for type inspection. The acceptance quality limit (AQL) is 2.5
Number of qualified determination
Items 7. and 7.2 of this standard are type inspection items, and the number of samples is 5. The inspection procedure is as follows: 9.1.2.2
Number of unqualified items
Take 3 sample barrels to inspect item 7.1, then use these 3 sample barrels for airtightness test, and then use these 3 sample barrels for hydraulic pressure test;
GR/T 13252-2008
b) Take 3 sample barrels from the remaining 5 sample barrels for compression test, and then use these 6 sample barrels for drop test. 9.2 Rules
9.2.1 Inspection
9.2.1.1 If there are two or more unqualified items in item 7.1, the sample is judged to be unqualified. If item 7.2.1 is unqualified, the sample is judged to be unqualified.
9.2.1.2 When the number of unqualified samples is greater than or equal to the number of unqualified judgments specified in Tables 12 and 13, the batch of products shall be deemed unqualified. 9.2.2 Type inspection
9.2.2.1 If two or more items in .1 are unqualified, the sample shall be deemed unqualified. If 1 sample is unqualified, the batch shall be deemed unqualified.
9.2.2.2 Inspect item by item according to 7.2 of this standard. If one item is unqualified, the sample shall be deemed unqualified. If 1 sample is unqualified, the batch shall be deemed unqualified:
Marking, transportation and storage
The manufacturer's mark or code shall be on the baggage.
The transported dog storage should be protected from rain, sun, moisture, pollution and deformation, etc. 9
GB/T13252-2008
Chinese Standards
Packing container
Steel bucket
GB/T 13252-2C08
Published and distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal code: 109C45
Website spc.net.cn
Tel: 6852394658517548
China Standards Press Taizhuodao Post Office Printing Name Assisted Xinhua Bookstore
Book 880×1230 -/16
Qiu Zhang 1
Mathematics 19,000 words
November 2008 edition November 2008 first printing number: 155065: 1-33939
If there is any printing error, the publishing center of our company will replace the version. Double exclusive infringement will be investigated
Report phone: (010) 685335334 Drop test
Danger level packaging
Danger level III and non-dangerous goods packaging 100
(3/T4857.5) will drop each product once to check for leakage. Contents and filling amount, drop location see Table 9, drop height see Table 1C, when the density of the liquid is greater than 1.2g/cm3, drop height see Table 11.9 Contents and filling amount, drop location
International Contents
Dropping degree/I
Exposure height/m
Mold Contents
For dry sand
Danger level packaging
95% of the penetration area
8% of the capacity
Table 10 Drop height
Dangerous packaging | |tt||Falling part
Welded chain, bottom, hoop edge and seam joint parts Hazard level and card Hazardous goods packaging
Falling height (when the density of the liquid is greater than 1.2g/cm2) Hazard level packaging
Liquid density × 1.5
Hazardous level packaging
Overall density × 1.2
Hazard level III non-hazardous goods packaging
Liquid density × 0.
After the 3rd and 4th category buckets fall, a small hole is made at the appropriate part of the lifting platform to balance the internal and external pressures, and check for leakage within 5 minutes. 8.5 Stacking test
According to the provisions of GB/T4857.3, the calcium push test time is 24h, and the stack load is: 12FCN. 7
GB/T 13252--2008
8.6 Handle and handle strength test
Fix the handle or handle with an appropriate method, then add a load of 600N vertically on the barrel body. After 5 minutes, check whether the handle, ring and connecting part are broken or damaged. 8.7 Determination of coating adhesion
Inspect in accordance with the provisions of C:B/T 1720. 9 Inspection rules
9.1 Handle inspection is divided into factory inspection and type inspection: 9.1.1 Factory inspection
9.1.1.17.1.1, 7.1.2, 7.1.3 and 7.2.1 are the inspection items. According to GB/T2828.1, the normal inspection is carried out once. 9.1.1.27.1.1, 7.1.2, 7.1.3 are the special inspection levels. S-3, acceptance quality limit is G. 1i, sampling number and qualified judgment number are shown in Table 12,
Table 12 Sampling number and qualified judgment number
Extended·second sampling
Batch range
5C1--3 200
3 201---35 000
35 001-~500 000
500001
Inspection level is S-3
Number of samples
Acceptance quality limit (AQI) is 6.5
Qualified judgment number
Unqualified judgment number
9. 1. 1. 37. 2.1 The inspection water is special inspection water S-1, and the acceptance quality limit is 2. 5. Sampling number and qualified judgment number Table 13. Table 13 Sampling number and qualified judgment number
Normal -1 batch
Batch range
501~-35 000
35 col
Plastic inspection
9. 1. 2. 1
Inspection level is S-1
Subject
When any of the following situations occurs, type inspection should be carried out: trial production and type identification of new products or conversion of old products; when there are changes in structure, materials and process that may affect product performance; during normal production, an inspection is carried out every six months; when the product is resumed after a long period of suspension;
When the inspection result is significantly different from the previous type inspection result; when the national quality supervision agency proposes the requirement for type inspection. The acceptance quality limit (AQL) is 2.5
Number of qualified determination
Items 7. and 7.2 of this standard are type inspection items, and the number of samples is 5. The inspection procedure is as follows: 9.1.2.2
Number of unqualified items
Take 3 sample barrels to inspect item 7.1, then use these 3 sample barrels for airtightness test, and then use these 3 sample barrels for hydraulic pressure test;
GR/T 13252-2008
b) Take 3 sample barrels from the remaining 5 sample barrels for compression test, and then use these 6 sample barrels for drop test. 9.2 Rules
9.2.1 Inspection
9.2.1.1 If there are two or more unqualified items in item 7.1, the sample is judged to be unqualified. If item 7.2.1 is unqualified, the sample is judged to be unqualified.
9.2.1.2 When the number of unqualified samples is greater than or equal to the number of unqualified judgments specified in Tables 12 and 13, the batch of products shall be deemed unqualified. 9.2.2 Type inspection
9.2.2.1 If two or more items in .1 are unqualified, the sample shall be deemed unqualified. If 1 sample is unqualified, the batch shall be deemed unqualified.
9.2.2.2 Inspect item by item according to 7.2 of this standard. If one item is unqualified, the sample shall be deemed unqualified. If 1 sample is unqualified, the batch shall be deemed unqualified:
Marking, transportation and storage
The manufacturer's mark or code shall be on the baggage.
The transported dog storage should be protected from rain, sun, moisture, pollution and deformation, etc. 9
GB/T13252-2008
Chinese Standards
Packing container
Steel bucket
GB/T 13252-2C08
Published and distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal code: 109C45
Website spc.net.cn
Tel: 6852394658517548
China Standards Press Taizhuodao Post Office Printing Name Assisted Xinhua Bookstore
Book 880×1230 -/16
Qiu Zhang 1
Mathematics 19,000 words
November 2008 edition November 2008 first printing number: 155065: 1-33939
If there is any printing error, the publishing center of our company will replace the version. Double exclusive infringement will be investigatedbZxz.net
Report phone: (010) 68533533Sampling number and qualified judgment number are shown in Table 12.
Table 12 Sampling number and qualified judgment number
Extended sampling
Batch range
5C1--3 200
3 201---35 000
35 001-~500 000
500001
Inspection level is S-3
Number of samples
Acceptance quality limit (AQI) is 6.5
Number of qualified judgment
Number of unqualified judgment
9. 1. 1. 37. 2.1 The inspection water is special inspection water S-1, and the acceptance quality limit is 2. 5. Sampling number and qualified judgment number Table 13. Table 13 Sampling number and qualified judgment number
Normal -1 batch
Batch range
501~-35 000
35 col
Plastic inspection
9. 1. 2. 1
Inspection level is S-1
Subject
When any of the following situations occurs, type inspection should be carried out: trial production and type identification of new products or conversion of old products; when there are changes in structure, materials and process that may affect product performance; during normal production, an inspection is carried out every six months; when the product is resumed after a long period of suspension;
When the inspection result is significantly different from the previous type inspection result; when the national quality supervision agency proposes the requirement for type inspection. The acceptance quality limit (AQL) is 2.5
Number of qualified determination
Items 7. and 7.2 of this standard are type inspection items, and the number of samples is 5. The inspection procedure is as follows: 9.1.2.2
Number of unqualified items
Take 3 sample barrels to inspect item 7.1, then use these 3 sample barrels for airtightness test, and then use these 3 sample barrels for hydraulic pressure test;
GR/T 13252-2008
b) Take 3 sample barrels from the remaining 5 sample barrels for compression test, and then use these 6 sample barrels for drop test. 9.2 Rules
9.2.1 Inspection
9.2.1.1 If there are two or more unqualified items in item 7.1, the sample is judged to be unqualified. If item 7.2.1 is unqualified, the sample is judged to be unqualified.
9.2.1.2 When the number of unqualified samples is greater than or equal to the number of unqualified judgments specified in Tables 12 and 13, the batch of products shall be deemed unqualified. 9.2.2 Type inspection
9.2.2.1 If two or more items in .1 are unqualified, the sample shall be deemed unqualified. If 1 sample is unqualified, the batch shall be deemed unqualified.
9.2.2.2 Inspect item by item according to 7.2 of this standard. If one item is unqualified, the sample shall be deemed unqualified. If 1 sample is unqualified, the batch shall be deemed unqualified:
Marking, transportation and storage
The manufacturer's mark or code shall be on the baggage.
The transported dog storage should be protected from rain, sun, moisture, pollution and deformation, etc. 9
GB/T13252-2008
Chinese Standards
Packing container
Steel bucket
GB/T 13252-2C08
Published and distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal code: 109C45
Website spc.net.cn
Tel: 6852394658517548
China Standards Press Taizhuodao Post Office Printing Name Assisted Xinhua Bookstore
Book 880×1230 -/16
Qiu Zhang 1
Mathematics 19,000 words
November 2008 edition November 2008 first printing number: 155065: 1-33939
If there is any printing error, the publishing center of our company will replace the version. Double exclusive infringement will be investigated
Report phone: (010) 68533533Sampling number and qualified judgment number are shown in Table 12.
Table 12 Sampling number and qualified judgment number
Extended sampling
Batch range
5C1--3 200
3 201---35 000
35 001-~500 000
500001
Inspection level is S-3
Number of samples
Acceptance quality limit (AQI) is 6.5
Number of qualified judgment
Number of unqualified judgment
9. 1. 1. 37. 2.1 The inspection water is special inspection water S-1, and the acceptance quality limit is 2. 5. Sampling number and qualified judgment number Table 13. Table 13 Sampling number and qualified judgment number
Normal -1 batch
Batch range
501~-35 000
35 col
Plastic inspection
9. 1. 2. 1
Inspection level is S-1
Subject
When any of the following situations occurs, type inspection should be carried out: trial production and type identification of new products or conversion of old products; when there are changes in structure, materials and process that may affect product performance; during normal production, an inspection is carried out every six months; when the product is resumed after a long period of suspension;
When the inspection result is significantly different from the previous type inspection result; when the national quality supervision agency proposes the requirement for type inspection. The acceptance quality limit (AQL) is 2.5
Number of qualified determination
Items 7. and 7.2 of this standard are type inspection items, and the number of samples is 5. The inspection procedure is as follows: 9.1.2.2
Number of unqualified items
Take 3 sample barrels to inspect item 7.1, then use these 3 sample barrels for airtightness test, and then use these 3 sample barrels for hydraulic pressure test;
GR/T 13252-2008
b) Take 3 sample barrels from the remaining 5 sample barrels for compression test, and then use these 6 sample barrels for drop test. 9.2 Rules
9.2.1 Inspection
9.2.1.1 If there are two or more unqualified items in item 7.1, the sample is judged to be unqualified. If item 7.2.1 is unqualified, the sample is judged to be unqualified.
9.2.1.2 When the number of unqualified samples is greater than or equal to the number of unqualified judgments specified in Tables 12 and 13, the batch of products shall be deemed unqualified. 9.2.2 Type inspection
9.2.2.1 If two or more items in .1 are unqualified, the sample shall be deemed unqualified. If 1 sample is unqualified, the batch shall be deemed unqualified.
9.2.2.2 Inspect item by item according to 7.2 of this standard. If one item is unqualified, the sample shall be deemed unqualified. If 1 sample is unqualified, the batch shall be deemed unqualified:
Marking, transportation and storage
The manufacturer's mark or code shall be on the baggage.
The transported dog storage should be protected from rain, sun, moisture, pollution and deformation, etc. 9
GB/T13252-2008
Chinese Standards
Packing container
Steel bucket
GB/T 13252-2C08
Published and distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal code: 109C45
Website spc.net.cn
Tel: 6852394658517548
China Standards Press Taizhuodao Post Office Printing Name Assisted Xinhua Bookstore
Book 880×1230 -/16
Qiu Zhang 1
Mathematics 19,000 words
November 2008 edition November 2008 first printing number: 155065: 1-33939
If there is any printing error, the publishing center of our company will replace the version. Double exclusive infringement will be investigated
Report phone: (010) 68533533
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.