Some standard content:
K.9 35-040
National Standard of the People's Republic of China
GB/T15425-2002
Generation G
EAN·UCC System
128 Barcode
UCC/EAN-128 har code
Published on July 18, 2002
People's Republic of China
General Administration of Quality Supervision, Inspection and Quarantine
Implemented on December 1, 2002
GH/T 15425—2002
Current Normative References
1 Terms and Definitions
4 Requirements
5 Parameters for the UCC/EAN-L2B Barcode
61 ICC/EAN-128 Barcode Character Coding/Evaluation Rules Appendix A (Informative Appendix)
Appendix B (Informative Appendix)
Appendix C (Normative Appendix)
Relationship between the value of the LCC/EAN-128 barcode character and the value of the A-value....LCCEAV128 Appendix 1: Calculation method of bar code symbol comparison character [Informative Appendix]
UJCX/FAN-128 Bar code symbol principle 1·Basic logic analysis 12
GA/T15425—2002
The standard product refers to the FAV-LICC standard No. 5\1ICC:/AV-138 bar code system specification jointly formulated by the International Article Abbreviation Association (EAN) and the American Uniform Code Council (LICC), and the GB/T15425\199 trade unit 12 registration code 3 is revised according to the actual situation of our network. The card label conforms to the technical requirements of EAN·Universal Specification in terms of technical content. The standard is a collection of 128-code barcodes specified in (5/T18.117200041283), and is completely consistent with the 128-code in terms of technical content such as system combination and character policy. The application of this standard is limited to EAN·U(C system label, which has been revised. Compared with the 1999 trade unit 1, the content has been modified in the following aspects:
1. The name of the standard is changed to EAN·System 1 Code\CC/ EAN128 barcode): 2. The original chapter "If the title is not in accordance with the applicable standard" was modified. 3. The technical and definition content was added. The entire content of the standard was adjusted according to EAN (C general standard). 5. The content about the size printing error of the LCEA.-12 case code was deleted. 6. The original standard for the printing position and its requirements were changed. \: Added Chapter 6 \1TC/AN-12 series code string encoding detailed code rules: 8. T attachment A (informative attachment) \Speed C/E AN-128 series code symbol length is small core original that is \ appendix 13 (causing material reduction \ bar code word value and ASCE use of the relationship \ and appendix informative appendix) \ UCC / EA128 combined code symbol processing basic trend "
this standard is implemented from the date of. Replace GB/T151251SS4. The three standard appendices (: is the standard medical reduction: non-standard appendix A list and appendix [all informative appendix this standard is the Chinese commodity end two center white well calculation, this standard starts from: China commodity coding center: this standard is arranged Drafting person: Xie Zuo. Wen Xiang, Qiang Wu Hai Shuang Qiu Ke. This standard specifies the structure, three sets of barcodes of EAN·CC system 128 barcode (hereinafter referred to as LC/EAN-128 barcode), barcode size, application parameters of EAN-128 barcode, encoding/decoding rules, etc. This standard is similar to EAN, LCC system I automatic identification and data verification, 2 Normative references || tt || The clauses in the following documents become the clauses of this standard through the use of this standard. The referenced documents with a date, all subsequent modifications (excluding errors) or revisions are not applicable to this standard. The parties to the agreement on the suitability of this standard shall use the latest version of these documents. For any undated referenced documents, the latest version is applicable to this standard: 1/T1588--: D9R General Technical Information Exchange Coded character scheme (c9[S/64:1591) GJ3129141998 Commodity barcode
GB12005-2033 Barcode technology
B/16186-123 Barcode application standard
G/T18H172R barcode (GE/T1R3472601.1SO/IFC1=417.2GD3.IT) 1S()/IEC15416 Information technology - dynamic recognition and data extraction technology
3 Technical training and definition||tt ||GBT1S05 standard terms and definitions for this standard: 4 Requirements
4.1 Symbol structure
LCCEAV-12H code characters can be composed of square to city I7 as shown; blank text on the side
-A start character Start (A, B or C)
-FNC character
Double character start center
System printing quality test standard
-One or more characters representing data and media symbols (created in brackets: -Check mark: The blank area on the right of the symbol indicates the payment receipt, etc., and the characters that can be recognized by the company are displayed below or on the upper right of the symbol. The UCC/EAN128 bar code symbol is in the format of the basic 4 format as shown in Figure 1: a linear symbol, etc. GA/T15425-2002... Super symbol digital line (00) 3501234512 34567894
*Wide area
Figure 1T1E heart E42128 bar code will be a short format of the number [CEAN-128 bar code character decoration
Blank area
CFAN-1: Bar code symbol format see Table 1: The valid value in the single width column represents the number of damaged blocks. Table 1 UCC/EAN-128 code character set A, B, C number
Character set A
Character set B
Chinese and English comparison
Bar, space arrangement
List
Study character match
Study record A
AS11 value
Character set t
Table 1 continuation:
List purchase
《Weir plan》
GR/T154252002
Pattern, complete arrangement
3+ ?./+'+++':i6.+[3m
GB:T 15425
Yandi A
Thai Tong)
Fu Ji ASCul position
Guan Mei
Unit home
Room arrangement
[5 1 2 3415+5-2815:1311
Main position
Word against pressure
Bao Fu Zhang Abzxz.net
CODEC!
Yu Jiang!
Study symbol
ASC1
Table 1 continued)
The symbol
Single child information
Number of vibration blocks
CB/T154252002
Article, study
snss2 ([to:
tTHF:A3
Parallel A5, set
Ning symbol Dong H
7% single A
1 end 1 word ￥H1 article 3 spaces·Total 13~Change group clause: 4.2.1 Bar code sub-symbol structure
Total element quality
According to the expansion clause
Article sample list
s 5 R- 11 2:- 5: :-
The mother code car symbol (the end of the description of the symbol) is composed of 6 single cotton fast distances of 3 stripes and 3 spaces, and each record or blue width and [to 4 times.
The positive symbol is the same as 1 stripe, a total of 7 single heart 13 hand-covered group tons. In the image code, the stripe is only a whole for the fake style, and the number of times is the number of destiny. The main odd and even symbol guarantees the self-checking of the bar code symbol, and the symbol guide of the start symbol is shown in the figure.
The structure of the N-12 bar code starting symbol under 2TC is \STARTA" GB/I 154252002
The uniform code Ning symbol is a row table of 5 cars, etc. A or B is "\ in the Ning symbol set is two numbers \3\[\
1313121
Figure 3UICX:/KAN-128 bar code character value is 35, the structure of the end character is shown in Figure 4:
Figure 41. (, EAN-12u bar code symbol structure 4.2.2 Data encoding
LCA1 three-character set A, 1C as shown in Table 1. H Ning character set with CB/T13347 A, we gave a mountain, the combination. The character set is sent according to the start character STARTAB or the conversion character (FA or SIIT) first. If the bar code symbol starts with the start character STARTA, the final element is completed. If the bar code symbol starts with the start character START, the final element is determined by the car #B: If the bar code symbol starts with the start character R Character table, or use the switch character to convert the character (S1 to the new character set (this is the use of special characters 1.2.4) too fast to use different start characters, negative derivatives and conversion characters to choose. The same number can be represented by different UCCEA128 bar code symbols. The book only uses the frequency and no fixed cost to make the country give the character case for the recorder to use the symbol length of any given data to support the rule. The coder can move the stroke and block the effective type of the period, and the switch and conversion according to the valid combination of characters to reverse the micro-row code, the year is equal to the Ting check a number column, can be loaded 1. This value is used to calculate and check the character symbol. It also provides a teaching environment that can be used with AIT.
4.2.3 Character bamboo prohibition
4. 2 3 1 word will be case A
Ya derivative set includes the land has not too write English words year, mathematics characters "first remember point control characters (A value groove) to the learning characters and a
4.2.3.2 word will be east B
character set is also active all standard use big text each mathematics learning to!, punctuation child control small American text Ning Yin character (ASCI value to enjoy: a special flash
4.2.3 3 characters will be collected
the main character is 0 99 and: people special characters have adopted the character set C when the year of the two Jinliang school,
4.2.1 special characters
etc. A published characters must be used after the characters are used (characters are S 1 to: the maximum 3 characters in the set (Ning character estimate GB/I154252002
133 rate 102> special non-excited characters have no pairs of ASC II character format. They have different meanings for the reading device. 4.2.4.1: Cut character C: ODE> and conversion character (SHIFT) In a 1: C/AN-128 code symbol, the cut character conversion character is used to convert a character to a foreign character set.
Shift character
Switch character ODE A: B. or () to convert the current character set to the new character set specified by the internal character A (B ). This conversion applies to: all characters after the cut-off, point to the end of the line or send zero; see an initial change character or conversion character 5) conversion box
conversion character 5HFT will convert the single unit from the A Korean conversion character set 4 or from the character set R to character A, in the conversion character production surface, the character will automatically or restore the character to the previous meaning of the character policy B4.2.4-2 function character: 1NC
can be used for this course to indicate the special operation or application of the piece) support SA (or C) and N from the FA system h) (information to indicate the system code source reading device, the information containing N symbols will be temporarily stored in the next symbol before transmission, during the transmission, it is possible to link several numbers, the symbol with the symbol file, if the data and the card meaning, why do you need to determine the symbols in the order of reading! The barcode reader is initialized by the card, and the format is also called F3 Ning. The number of megabytes is used to initialize the barcode reader. The secret word can appear in any part of the code. dNC is not implemented in EAN·EICC.
4.2.5 Start and stop characters
The start character trB or the end character is used at the beginning of the symbol. The end character Srop is used to analyze it. 4.2.6 Check symbol
The last character before the barcode symbol ends. The calculation method is recorded in the center for human recognition. It is not indicated in the check material
4.2.7UCEAN12B barcode start format
ICCFAN-barcode has a special start symbol, the format is as follows: F: Starr AR & C FNt
This double-character start symbol! Can distinguish UC/EAN! 2S barcode is different from 128 barcode. If a 29-year code starts with a double character, it is a JCC/EAN1 barcode. Otherwise, it must be a TC/AV code.
FN can be used as a check character (with a small chance of error). When selecting a barcode, use the following characters:
S:r to use LCFANI28 system code, 4T to start Srsn to use CCEAN-1 barcode. Su: IC/FAN-126 ※ The barcode starts with a character pattern, usually containing data in 4 or more characters.
4.3 Size requirements
FAN-1 barcode size requirements are as follows:
4.3.1 The minimum module density (X
must be within the specified range and must be determined based on the actual product and reading equipment. The minimum size is 000 and the maximum size is 1.00. Each time a standard value of one inch is used: In the given system, the actual change is 7
CB/T15425-2DC2
4.3.2 Space
UCC/EAN12 barcode symbols in the minimum area of 10X4.4 Reference translation method
The barcode reading system is designed for the actual medical algorithm to allow for the reading of multiple codes with missing codes. In the analysis of the whole decoding solution described in the section, the calculation of the value of 2 is shown in section 4.5. The steps for translating each barcode character are as follows: 1 Calculate the width of 8 bars (Figure 5)
Figure 5 The code size is
Convert , to the corresponding value, , and express it as a multiple of the decision width: The calculation method is as follows
If 1./1* 2./1, the area, = 2
If 2.52/11* 3.5/1, then E,3; if, 51e1. 51E, =;
If .5/11.5/1,
If 5.5+/116,5/11. Then, = 6;
If, 5/11m 7.p/11, then, = 7, otherwise the code is incorrect.
3Use a value, ,, and F as the key to find the character in the decoding table. (See Table)) Find the check value V of the character in the text, the value should be compared with the module validation formula of the text:
(1.75p (+.-6: (V + 1.)p/1. If it does not hold, the character is incorrectly recognized.
The algorithm indirectly uses the code character's validity period to find the error of a single module of the system. For more than 5 bar codes, if the first bar code character is the start character, then repeat from left to right. If the first bar code character is not the start character but the end character, then replace the code character in the opposite direction. When all the code characters have been replaced, ensure that there is a valid start character and a valid end character. Ⅲ. Use a correct symbol to verify the character.
According to the start character, switch character and change character in the bar code symbol, the character of the symbol is converted into an appropriate data interpretation.
Let: the calculation of this must be generated, using a recognized low-cost size: plus an additional size, that is, the sum of x
GB/T154252002
decay 2 to 128 high-speed decoding edge explosion difference y
Yu Fu BaiThe same number can be represented by different UCCEA128 barcode symbols. The book provides no specific rules for the symbol length of any given data. The encoder can effectively switch and reverse the code by checking a number column that is equal to 1. This value is used to calculate and check the symbol of the character. It also provides a teaching environment that can be used with AIT. Attached is required.
4.2.3 Characters are forbidden
4. 2 3 1 Characters will be included in the A
Ya derivative set includes the English characters that are not written in the year, mathematical characters "the first memory point to control the characters (A value groove) to the learning characters and a natural
4.2.3.2 Characters will be included in the B
Character set is also active all standard characters every mathematical learning to!, punctuation control small American text Ning Yin character (ASCI value to enjoy: a special flash
4.2.3 3 characters will be collected in the heart
the two-digit code 0 main 99 and: the special characters in the world are represented by the two Jinliang school characters,
4.2.1 Special characters
etc. A-printed characters are used to represent 1 character after the share (the characters are S 1 to: the maximum 3 characters in the set (the characters are estimated GB/I154252002
133 rate 102> special non-excited characters have no corresponding ASCII character format. They have the desired meaning for the reader, 4.2.4.1: C:ODE> and conversion characters (SHIFT) in a 1:C/AN-128 recording code symbol In the character conversion function, a character is converted to another character set.
Change character
Switch character ODEA:B. or () will convert the current character set to a new character set (B changes to the center). This conversion applies to: all characters after the cut, until the end of the line or zero; see an initial change character or conversion character 5) conversion box
Conversion character 5HFT will convert the single character from the A Korean change character set 4 or from the character set R to character A, and the character set will be automatically or restored to the previous character set in the conversion character policy B4.2 .4-2 Function code: 1NC
Can be used for bar code reading equipment. This equipment can indicate the special operation or application of the device. The start code SA (or C) and the N start code FA system (h) (information addition instruction system code source reading equipment, the graphic information containing N symbols is temporarily stored before the next symbol is transmitted. During the transmission, it is possible to link several numbers. The symbol is located in the file of the symbol. If the data is related to the card, it is necessary to determine the order of the symbols to be read! The card is initialized by the bar code reading equipment, and the number of F3 and other megabytes is used as the initialization instruction for the new programming of the bar code recognition device. The word storage can be Now the dNC is not implemented in EAN/EICC.
4.2.5 Start and stop characters
The start character trB or the end character is used at the beginning of the symbol. The end character Srop is used for analysis. 4.2.6 Check character
The last character before the end of the bar code symbol. The calculation method is recorded in the text for human recognition.
4.2.7UCEAN12B bar code start format
ICC FAN-type bar code has a special start symbol, the format is as follows: F: Starr AR & C FNt
This double-letter start symbol can be distinguished from UC/EAN! If a 128 barcode starts with a double character, then it is a JCC/EAN1 barcode. Otherwise, it must be a TC/AV barcode.
FN can be used as a check character (with a small chance of error). When selecting a barcode, use the following characters:
S:r to make the LCFANI28 barcode start with Srsn and the CCEAN-1 barcode start with Srsn. Su: IC/FAN-126 ※ The barcode starts with a character pattern, usually containing data in 4 or more characters.
4.3 Size requirements
FAN-1 barcode size requirements are as follows:
4.3.1 The minimum module density (X
must be within the specified range and must be determined based on the actual product and reading equipment. The minimum size is 000 and the maximum size is 1.00. Each time a standard value of one inch is used: In the given system, the actual change is 7
CB/T15425-2DC2
4.3.2 Space
UCC/EAN12 barcode symbols in the minimum area of 10X4.4 Reference translation method
The barcode reading system is designed for the actual medical algorithm to allow for the reading of multiple codes with missing codes. In the analysis of the whole decoding solution described in the section, the calculation of the value of 2 is shown in section 4.5. The steps for translating each barcode character are as follows: 1 Calculate the width of 8 bars (Figure 5)
Figure 5 The code size is
Convert , to the corresponding value, , and express it as a multiple of the decision width: The calculation method is as follows
If 1./1* 2./1, the area, = 2
If 2.52/11* 3.5/1, then E,3; if, 51e1. 51E, =;
If .5/11.5/1,
If 5.5+/116,5/11. Then, = 6;
If, 5/11m 7.p/11, then, = 7, otherwise the code is incorrect.
3Use a value, ,, and F as the key to find the character in the decoding table. (See Table)) Find the check value V of the character in the text, the value should be compared with the module validation formula of the text:
(1.75p (+.-6: (V + 1.)p/1. If it does not hold, the character is incorrectly recognized.
The algorithm indirectly uses the code character's validity period to find the error of a single module of the system. For more than 5 bar codes, if the first bar code character is the start character, then repeat from left to right. If the first bar code character is not the start character but the end character, then replace the code character in the opposite direction. When all the code characters have been replaced, ensure that there is a valid start character and a valid end character. Ⅲ. Use a correct symbol to verify the character.
According to the start character, switch character and change character in the bar code symbol, the character of the symbol is converted into an appropriate data interpretation.
Let: the calculation of this must be generated, using a recognized low-cost size: plus an additional size, that is, the sum of x
GB/T154252002
decay 2 to 128 high-speed decoding edge explosion difference y
Yu Fu BaiThe same number can be represented by different UCCEA128 barcode symbols. The book provides no specific rules for the symbol length of any given data. The encoder can effectively switch and reverse the code by checking a number column that is equal to 1. This value is used to calculate and check the symbol of the character. It also provides a teaching environment that can be used with AIT. Attached is required.
4.2.3 Characters are forbidden
4. 2 3 1 Characters will be included in the A
Ya derivative set includes the English characters that are not written in the year, mathematical characters "the first memory point to control the characters (A value groove) to the learning characters and a natural
4.2.3.2 Characters will be included in the B
Character set is also active all standard characters every mathematical learning to!, punctuation control small American text Ning Yin character (ASCI value to enjoy: a special flash
4.2.3 3 characters will be collected in the heart
the two-digit code 0 main 99 and: the special characters in the world are represented by the two Jinliang school characters,
4.2.1 Special characters
etc. A-printed characters are used to represent 1 character after the share (the characters are S 1 to: the maximum 3 characters in the set (the characters are estimated GB/I154252002
133 rate 102> special non-excited characters have no corresponding ASCII character format. They have the desired meaning for the reader, 4.2.4.1: C:ODE> and conversion characters (SHIFT) in a 1:C/AN-128 recording code symbol In the character conversion function, a character is converted to another character set.
Change character
Switch character ODEA:B. or () will convert the current character set to a new character set (B changes to the center). This conversion applies to: all characters after the cut, until the end of the line or zero; see an initial change character or conversion character 5) conversion box
Conversion character 5HFT will convert the single character from the A Korean change character set 4 or from the character set R to character A, and the character set will be automatically or restored to the previous character set in the conversion character policy B4.2 .4-2 Function code: 1NC
Can be used for bar code reading equipment. This equipment allows special operation or application of the device. The start code SA (or C) and the N start code FA system h) (information to add the system code source reading equipment, the graphic containing N symbols will be temporarily stored before the next symbol is transmitted. During the transmission, it is possible to link several numbers. The symbol is located in the file of the symbol. If the data is related to the card, it is necessary to determine the order of the symbols to be read! The card is initialized by the bar code reading equipment, and the number of F3 and other megabytes is used as the initialization instruction for the new programming of the bar code recognition device. The word storage can be Now the dNC is not implemented in EAN/EICC.
4.2.5 Start and stop characters
The start character trB or the end character is used at the beginning of the symbol. The end character Srop is used for analysis. 4.2.6 Check character
The last character before the end of the bar code symbol. The calculation method is recorded in the text for human recognition.
4.2.7UCEAN12B bar code start format
ICC FAN-type bar code has a special start symbol, the format is as follows: F: Starr AR & C FNt
This double-letter start symbol can be distinguished from UC/EAN! If a 128 barcode starts with a double character, then it is a JCC/EAN1 barcode. Otherwise, it must be a TC/AV barcode.
FN can be used as a check character (with a small chance of error). When selecting a barcode, use the following characters:
S:r to make the LCFANI28 barcode start with Srsn and the CCEAN-1 barcode start with Srsn. Su: IC/FAN-126 ※ The barcode starts with a character pattern, usually containing data in 4 or more characters.
4.3 Size requirements
FAN-1 barcode size requirements are as follows:
4.3.1 The minimum module density (X
must be within the specified range and must be determined based on the actual product and reading equipment. The minimum size is 000 and the maximum size is 1.00. Each time a standard value of one inch is used: In the given system, the actual change is 7
CB/T15425-2DC2
4.3.2 Space
UCC/EAN12 barcode symbols in the minimum area of 10X4.4 Reference translation method
The barcode reading system is designed for the actual medical algorithm to allow for the reading of multiple codes with missing codes. In the analysis of the whole decoding solution described in the section, the calculation of the value of 2 is shown in section 4.5. The steps for translating each barcode character are as follows: 1 Calculate the width of 8 bars (Figure 5)
Figure 5 The code size is
Convert , to the corresponding value, , and express it as a multiple of the decision width: The calculation method is as follows
If 1./1* 2./1, the area, = 2
If 2.52/11* 3.5/1, then E,3; if, 51e1. 51E, =;
If .5/11.5/1,
If 5.5+/116,5/11. Then, = 6;
If, 5/11m 7.p/11, then, = 7, otherwise the code is incorrect.
3Use a value, ,, and F as the key to find the character in the decoding table. (See Table)) Find the check value V of the character in the text, the value should be compared with the module validation formula of the text:
(1.75p (+.-6: (V + 1.)p/1. If it does not hold, the character is incorrectly recognized.
The algorithm indirectly uses the code character's validity period to find the error of a single module of the system. For more than 5 bar codes, if the first bar code character is the start character, then repeat from left to right. If the first bar code character is not the start character but the end character, then replace the code character in the opposite direction. When all the code characters have been replaced, ensure that there is a valid start character and a valid end character. Ⅲ. Use a correct symbol to verify the character.
According to the start character, switch character and change character in the bar code symbol, the character of the symbol is converted into appropriate data interpretation.
Let: the calculation of this must be generated, using a recognized low-cost size: plus an additional size, that is, the sum of x
GB/T154252002
decay 2 to 128 high-speed decoding edge explosion difference y
Yu Fu BaiOr () convert the current symbol set into the new character set A (B change heart). This conversion applies to: all characters after the cut-off, point to the end of the line or send zero; see an initial change character or conversion character 5) conversion box
conversion character 5HFT will convert the single unit from the A Korean conversion character set 4 or from the character set R to character A, and the character in the conversion character will be automatically or restored to the previous character in the conversion list. B4.2.4-2 Function Character: 1NC
Can be used for this course to indicate the special operation or application of the piece) start character SA (or C) and N is used for marking the system's h) (information addition to indicate the system code source reading device, the information containing the N symbol is temporarily stored in the next symbol before transmission, during transmission, it is possible to link several numbers, the symbol is located in the symbol file, if the data is compatible with the card, part of it It is necessary to make sure that the symbols are read in the correct order! When the barcode reader is initialized, the format of the barcode reader is F3, etc. as the initialization instruction. The character can appear in any part of the code. dNC is not implemented in EAN·EICC.
4.2.5 Start and stop characters
The start character trB or the end character is used at the beginning of the symbol. The end character Srop is used for analysis. 4.2.6 Check character
The check character is the last character before the end of the barcode symbol. The calculation method is shown in the table for human recognition.
4.2.7 UCEAN12B barcode start format
ICC FAN-type barcodes have a special start symbol, the formula is as follows: F: Starr AR & C FNt
This double character starts with a 128 barcode! It can be distinguished from UC/EAN! 2S barcodes are different from 128 barcodes. If a 29-year code starts with a double character, it is a JCC/EAN1 barcode. Otherwise, it must be a TC/AV code.
FN can be used as a check character (possibility is less than 10%). When the batch identifier is selected and its domain is included in the barcode, the above 1 is used as a separate character:
S:r Use LCFANI28 system codes to start with 4T Srsn Use CCEAAN-1 tea barcodes to set B. Su:: C IC/FAN-126 ※ The code starts with a character, usually for the data that includes the identifier in 4 or more F numbers,
4.3 Size requirements
FAN-1 barcode number The size requirements are as follows:
4.3.1 The minimum size of the module (X
) is determined by the actual size of the product and the reading equipment. The minimum size is 000 and the maximum size is 1.00. Each time the product is produced, the daily standard value of one size is reported in: a given system is used for a final change of 7
CB/ T15425—2DC2
4.3.2 The minimum size of the blank area
UCC/EAN12 bar and other symbols in the wide area is 10X4.4 Reference translation method
The reading system is designed to allow for the actual medical algorithm to be able to read multiple codes with missing characters. In the analysis and decoding method described in the section, the value of Sichuan Medicine 2 can be found in section 4.5. The steps for translating each barcode character are as follows: 1. Calculate the width of the 8 scales (Figure 5).
Figure 5. Code size
Convert
to the corresponding width, and express it as a multiple of the code width: The calculation method for each scale is as follows:
If 1./1* 2./1, then
then 2.52/11* 3.5/1, then 3; if 51e1. 51E, =;
then .5/11.5/1,
then 5. 5+/116,5/11. then , = 6;
If 5/11m 7. p/11, then , = 7, otherwise the barcode character is incorrect.
3 Take 1 value,,,, and F as the key to find the character in the decoding table. (See Table)) Find the check value V of the character in the text, the value should be compared with the module validation formula of the character:
(1.75p (+.-6: (V + 1.)p/1 If it does not hold, the character is not recognized correctly.
This algorithm indirectly uses the code character's performance to find the error of the single module of the system. For more than 5 special policies, if the first bar code character is the start character, then repeat from left to right. If the first bar code character is not the start character but the end character, then replace the code character in the opposite direction. When all the code characters are replaced, it is guaranteed that there is a valid start character and a valid end character. Ⅲ. Use a correct symbol to verify the character.
According to the start character, switch character and change character in the bar code symbol, the character of the symbol is converted into an appropriate data interpretation.
Let: the calculation of this must be generated, using a recognized low-cost size: plus an additional size, that is, the sum of x
GB/T154252002
decay 2 to 128 high-speed decoding edge explosion difference y
Yu Fu BaiOr () convert the current symbol set into the new character set A (B change heart). This conversion applies to: all characters after the cut-off, point to the end of the line or send zero; see an initial change character or conversion character 5) conversion box
conversion character 5HFT will convert the single unit from the A Korean conversion character set 4 or from the character set R to character A, and the character in the conversion character will be automatically or restored to the previous character in the conversion list. B4.2.4-2 Function Character: 1NC
Can be used for this course to indicate the special operation or application of the piece) start character SA (or C) and N is used for marking the system's h) (information addition to indicate the system code source reading device, the information containing the N symbol is temporarily stored in the next symbol before transmission, during transmission, it is possible to link several numbers, the symbol is located in the symbol file, if the data is compatible with the card, part of it It is necessary to make sure that the symbols are read in the correct order! When the barcode reader is initialized, the format of the barcode reader is F3, etc. as the initialization instruction. The character can appear in any part of the code. dNC is not implemented in EAN·EICC.
4.2.5 Start and stop characters
The start character trB or the end character is used at the beginning of the symbol. The end character Srop is used for analysis. 4.2.6 Check character
The check character is the last character before the end of the barcode symbol. The calculation method is shown in the table for human recognition.
4.2.7 UCEAN12B barcode start format
ICC FAN-type barcodes have a special start symbol, the formula is as follows: F: Starr AR & C FNt
This double character starts with a 128 barcode! It can be distinguished from UC/EAN! 2S barcodes are different from 128 barcodes. If a 29-year code starts with a double character, it is a JCC/EAN1 barcode. Otherwise, it must be a TC/AV code.
FN can be used as a check character (with a small chance of error). When the batch identifier is selected and its domain is included in the barcode, the above 1 is used as a separate character:
S:r Use LCFANI28 system codes to start with 4T Srsn Use CCEAAN-1 tea barcodes to set B. Su:: C IC/FAN-126 ※ The code starts with a character, usually for the data that includes the identifier in 4 or more F numbers,
4.3 Size requirements
FAN-1 barcode number The size requirements are as follows:
4.3.1 The minimum size of the module (X
) is determined by the actual size of the product and the reading equipment. The minimum size is 000 and the maximum size is 1.00. Each time the product is produced, the daily standard value of one size is reported in: a given system is used for a final change of 7
CB/ T15425—2DC2
4.3.2 The minimum size of the blank area
UCC/EAN12 bar and other symbols in the wide area is 10X4.4 Reference translation method
The reading system is designed to allow for the actual medical algorithm to be able to read multiple codes with missing characters. In the analysis and decoding method described in the section, the value of Sichuan Medicine 2 can be found in section 4.5. The steps for translating each barcode character are as follows: 1. Calculate the width of the 8 scales (Figure 5).
Figure 5. Code size
Convert
to the corresponding width, and express it as a multiple of the code width: The calculation method for each scale is as follows:
If 1./1* 2./1, then
then 2.52/11* 3.5/1, then 3; if 51e1. 51E, =;
then .5/11.5/1,
then 5. 5+/116,5/11. then , = 6;
If 5/11m 7. p/11, then , = 7, otherwise the barcode character is incorrect.
3 Take 1 value,,,, and F as the key to find the character in the decoding table. (See Table)) Find the check value V of the character in the text, the value should be compared with the module validation formula of the character:
(1.75p (+.-6: (V + 1.)p/1 If it does not hold, the character is not recognized correctly.
This algorithm indirectly uses the code character's performance to find the error of the single module of the system. For more than 5 special policies, if the first bar code character is the start character, then repeat from left to right. If the first bar code character is not the start character but the end character, then replace the code character in the opposite direction. When all the code characters are replaced, it is guaranteed that there is a valid start character and a valid end character. Ⅲ. Use a correct symbol to verify the character.
According to the start character, switch character and change character in the bar code symbol, the character of the symbol is converted into an appropriate data interpretation.
Let: the calculation of this must be generated, using a recognized low-cost size: plus an additional size, that is, the sum of x
GB/T154252002
decay 2 to 128 high-speed decoding edge explosion difference y
Yu Fu BaiThe steps for translating each barcode character are as follows: 1. Calculate the width of the 8-bit barcode) (Figure 5) Code size
Convert
to the corresponding width, and express it as a multiple of the width: The calculation method for each barcode character is as follows:
If 1./1* 2./1,
then 2.52/11* 3.5/1, then 3; if 51e1. 51E, =;
then .5/11.5/1,
then 5. 5+/116,5/11. Then , = 6;
If 5/11m 7. p/11, then , = 7, otherwise the barcode character is incorrect.
3 Take 1 value,,,, and F as the key to find the character in the decoding table. (See Table)) Find the check value V of the character in the text, the value should be compared with the module validation formula of the character:
(1.75p (+.-6: (V + 1.)p/1 If it does not hold, the character is not recognized correctly.
This algorithm indirectly uses the code character's performance to find the error of the single module of the system. For more than 5 special policies, if the first bar code character is the start character, then repeat from left to right. If the first bar code character is not the start character but the end character, then replace the code character in the opposite direction. When all the code characters are replaced, it is guaranteed that there is a valid start character and a valid end character. Ⅲ. Use a correct symbol to verify the character.
According to the start character, switch character and change character in the bar code symbol, the character of the symbol is converted into an appropriate data interpretation.
Let: the calculation of this must be generated, using a recognized low-cost size: plus an additional size, that is, the sum of x
GB/T154252002
decay 2 to 128 high-speed decoding edge explosion difference y
Yu Fu BaiThe steps for translating each barcode character are as follows: 1. Calculate the width of the 8-bit barcode) (Figure 5) Code size
Convert
to the corresponding width, and express it as a multiple of the width: The calculation method for each barcode character is as follows:
If 1./1* 2./1,
then 2.52/11* 3.5/1, then 3; if 51e1. 51E, =;
then .5/11.5/1,
then 5. 5+/116,5/11. Then , = 6;
If 5/11m 7. p/11, then , = 7, otherwise the barcode character is incorrect.
3 Take 1 value,,,, and F as the key to find the character in the decoding table. (See Table)) Find the check value V of the character in the text, the value should be compared with the module validation formula of the character:
(1.75p (+.-6: (V + 1.)p/1 If it does not hold, the character is not recognized correctly.
This algorithm indirectly uses the code character's performance to find the error of the single module of the system. For more than 5 special policies, if the first bar code character is the start character, then repeat from left to right. If the first bar code character is not the start character but the end character, then replace the code character in the opposite direction. When all the code characters are replaced, it is guaranteed that there is a valid start character and a valid end character. Ⅲ. Use a correct symbol to verify the character.
According to the start character, switch character and change character in the bar code symbol, the character of the symbol is converted into an appropriate data interpretation.
Let: the calculation of this must be generated, using a recognized low-cost size: plus an additional size, that is, the sum of x
GB/T154252002
decay 2 to 128 high-speed decoding edge explosion difference y
Yu Fu Bai
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.