JB/T 9850-1999 This standard is a revision of ZB J48 008-89 "Pneumatic Riveting Machine". During the revision, the "cylinder diameter" technical parameter of the original standard was cancelled. This standard specifies the types and basic parameters, technical requirements, test methods and inspection rules and marking, packaging, transportation and storage of pneumatic riveting machines. This standard applies to pneumatic riveting machines. This standard was first issued in , first revised in , and second revised in . This is the th revision. JB/T 9850-1999 Pneumatic Riveting Machine JB/T9850-1999 Standard download decompression password: www.bzxz.net

[CS 25.140.10
Machinery Industry Standard of the People's Republic of China
JB/T9850-—1999
Pneumatic riveting machine
Pneumatic riveting machine
1999-06-28 Issued
National Bureau of Machinery Industry
2000-01-01 Implementation
JB/T9850-1999
This standard is a revision of ZBJ48008—89 "Pneumatic nailing machine". During the revision, the basic parameter "cylinder" in the original standard was cancelled.
This standard shall replace ZBJ4800889 from the date of implementation. This standard was proposed and managed by the National Technical Committee for Standardization of Rock Drilling Machinery and Pneumatic Machinery. The drafting unit of this standard: Shenyang Huangyan Machinery Co., Ltd. The main drafters of this standard are Wang Xucha and Yue Fu. 1 Fan Yuan
Machinery Industry Standard of the People's Republic of ChinabzxZ.net
Pneumatic Riveting Machine
Pneumatke riveting hammers
JB/T 9850-1999
7148089
This standard specifies the types and basic specifications, technical requirements, test methods and inspection specifications and markings, packaging, transportation and storage of pneumatic nailing machines.
This standard applies to pneumatic riveting machines.
2 Cited Standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is issued, the versions shown are all valid. All standards will be revised. The parties using this standard should explore the possibility of using the latest versions of the following standards. All published standards will be revised. The parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T 2828 — 1987 | | tt | | GB.T5621 — 1999 | t||JB/T40411994
JB/T7161—1993
JB/71M—1993
JB/T 7302—1994
JDT 9857—t999
3 Types and basic parameters
Batch inspection, counting, sampling, and sampling table (applicable to inspection of continuous batches) Performance test methods for rock drilling machinery and pneumatic tools Performance test methods for rock drilling machinery and pneumatic tools "Noise measurement method" Process method Rock drilling machinery and pneumatic tools Handle matching size General technical conditions for packaging of electromechanical products
Product model compilation method for rock drilling machinery and pneumatic tools General technical conditions for rust prevention of rock drilling machinery and pneumatic tools General testing method for product full-scale elimination of rock drilling machinery and pneumatic tools General technical provisions for potential treatment of rock drilling machinery and pneumatic tools General technical provisions for mechanical processing parts of rock drilling machinery and pneumatic tools General technical conditions for product packaging of rock drilling machinery and pneumatic tools General technical conditions for painting of rock drilling machinery and pneumatic tools 3.1 Product structure types are as follows:
a) Straight handle type (see Figure!);
b) Check handle type (see Figure 2 ;
c Bent handle type (see Figure 3
d Ring handle type [see Figure 4
3.2 Basic parameters shall comply with the provisions of Table 1. 3.3 The size and tolerance of the tail handle and the cylinder hole [hole] shall comply with the provisions of GB/T374. 3.4 Product models shall be compiled in accordance with JB/T1590 System, Figure 1 straight pick
Figure 3 bent pick
Jinhe Direct Sales
According to technical requirements
Each head handle
12×45
17×60
Air pressure
Middle impact
Figure 2 gun handle
Figure ring handle
Impact rate
Air consumption||tt ||4.1 The product shall comply with the requirements of this standard and be manufactured according to the drawings and technical documents approved by the prescribed procedures. *.1 The performance index of the product shall comply with the provisions of 3.2. 4.3 The quality of mechanical parts shall comply with the provisions of IB/T7164: 4.4 The quality of heat-treated parts shall comply with the provisions of IB/T716! 4.5 The rust prevention of products shall comply with the provisions of JB/T3576. Gas
(sound power level)
4.6 The connection of the product shall comply with the provisions of JB/T9857. JB/T9850-1999
4.7 Except for the valve and the valve, the other parts shall be interchangeable and assembled according to the requirements of the general assembly drawing: 4.8 All parts [including external parts, purchased parts, and standard parts] must be inspected and qualified by the inspection department before they can be assembled and packed. 4.9 The surface of the product shall not be scratched, and there shall be clear, straight, and neat marks. 4.10 The cleanliness of the product shall comply with the provisions of Table 2. 2
Product Specifications
Cleanliness Scheduling
5 Test Methods and Inspection Rules
5.1 Products must be technically qualified by the manufacturer and accompanied by a product certificate before they can leave the factory. 5.2 The performance test of the product shall be carried out in accordance with the provisions of GBT5621. 53 The measurement of product noise shall be carried out in accordance with the provisions of GB58. 5.4 The cleanliness test of the product shall be carried out in accordance with the provisions of JB/T404I. 5.5 The surface quality inspection of the product shall comply with the provisions of 4.9. 5.6 The product shall be subjected to type inspection in the following circumstances: a) when new products (including old products when they are transferred to the factory for production) are being inspected; b) when the product has major changes in design, process and materials used; c) when the production of phased dust production is resumed; d) products produced in batches shall be conducted every 3-5 years. 5. The products to be subjected to type inspection shall be randomly selected from the qualified products for inspection. 19
5.8 When sampling product quality, the normal inspection specified in GB/T2828 shall be carried out as a single sampling. Marking, packaging, transportation and storage
6.1 Each product shall be marked with the following contents: a) Name of manufacturer or trademark: b) Product model: 3) Factory number (or batch number) 4) Manufacturing date (year, month) 5) Product packaging shall comply with the provisions of B/T7302. Export product packaging shall comply with the provisions of GE/T13384. 6.3 The following technical documents shall be attached to the product packaging: 2) Packing list: b) Product certificate; c) Product manual. 6.4 Products shall be waterproof, moisture-proof and sun-proof during transportation and storage. 36
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.