This standard specifies the type and basic parameters, technical requirements, test methods, inspection rules, marking, packaging, transportation and storage, and manufacturing guarantee of vertical compound crushers. JB/T 10343-2002 Vertical compound crusher JB/T10343-2002 Standard download decompression password: www.bzxz.net

1Cs 79.120
Machinery Industry Standard of the People's Republic of China
JB/T10343—2002
Vertical Compound Crusher
Complex Yertical Impact Crusher2002-07-16PromulgatedWww.bzxZ.net
2002-12-01Implementation
Promulgated by the State Economic and Trade Commission of the People's Republic of ChinaForeword
Period specificationThis document shall apply to the following articles
4. Technical requirements.
Basic technical level
Appearance cost requirements
Parts requirements.
Complete machine requirements
Empty load and running requirements
4.6 Completeness
5 Methods,
Heart starting rules
? Marking, packaging, transportation and storage
JR/110343.2002
This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association. This standard is issued by China Machinery Industry Association.
This standard applies to vertical composite crusher for materials below 1MMP (hereinafter referred to as crusher).
The following documents are cited by reference to this standard and become the provisions of this standard. For dated references, all subsequent internal amendments, excluding those with errors) or revised versions are not applicable to this standard: however, parties who have reached an agreement on this standard are encouraged to study and use the latest versions of these documents. For undated references, the latest version applies to this standard. G inch 19-2000 Packaging blockage pictorial mark ([S730: 1997) B3768 1996 Acoustic sound correction method for determining the production source yield level should be radiated m above the envelope surface belt method (EQV3SO3746: 1995 GR50871999 Production equipment safety and health measurement: C4DIN3100aVDE10U: 1993) 108 GB.T 5680 GBT 8923 GETO239 GBT J330K—199)
High-rise steel design
Pre-installation material surface and decoration etc. Leading grade eISo850-1:10s8 Special wide semi-balanced station quality allowed to determine the same unbalance (1SO1940-:198) sign
GBT 13384--15)2
B/T5U.3—1998
JE/TSCK0.1S1998
3Type and basic parameters
Huidian product color material installation parts
Vertical profit machinery, use drum multi-material connection parts
Complete machine and use support technology system steel parts non-destructive testing 3: The type of the nuclear machine is vertical induction rotor demagnetizing machine, as shown in Figure 1, the specific structure of the machine is: JH/T10343—2002
The limit parameters of these machines are as follows:
Simplified final operation time
10~-25
25~-41
a -- tx
90·120
100-140
Design: The capacity of the six types of cattle is determined according to the following cases: waste reduction energy: 60M:
loose dense.Vm
Material must be uniform:
Feed material tax piece
: 811
-: 20℃:
795~858
615--6F
3807 -425
335--370
Engine power:
One level machine can be used to produce different products with different properties, and the requirements cannot be met. Technical requirements
4.1 Basic requirements
4.1.! The crushing machine shall meet the requirements of the standard and be manufactured in accordance with the technical specifications and technical documents. 4.1.2 The parts of the same type of crusher shall not be interchangeable. 4.13 The bearings shall have good internal dust sealing devices, and no dust shall penetrate into the bearings. Oil shall not be allowed to spread on the bearings. 4.1.4 The sensor head, impact transformer, material tray and other wearing parts shall be replaced in a proper manner. 4.1.5 The parts shall be used in accordance with the specifications of GB/T 53-9 without affecting the performance of the product. 4.2 Appearance requirements
4.2.1 The surface of the crusher shall not be damaged during cleaning. 22 Before painting of welded parts or defective parts, the surface shall be derusted and deoxidized. The air volume shall not be lower than the requirements of GB/T 3923-198% ± S level
4 .2.3 The surface coating shall be uniform in color and smooth, and shall not have pores, airflow, delamination, flow support and coating pits. 4.3 Parts Requirements
4.3.1 Welding and other standards BT5000.3-1995 [. 4.32 Rotation, simplified, muscle benefits. Point plate, etc. The length of the variable parts shall not be marked with carbon limit deviation grams in accordance with the full B Ting 503-1% 1% medium grade Huang
4.3.3 High-speed steel coupons (568199 provisions 4 34 Chain counterattack HRC, Chishan 8m43.5 main advantage: small damage Ling afraid: should meet 1/T5000.151998 V road current 4.4 machine requirements
4.4.1 plate war test, rotation; rotation effect record active, stable. Health and quality to allow the board to prove, the layout of the operation of the time, there must be no resistance, start the dynamic phenomenon
4.42 general method before: the first: free the second rotor should be brought to the test, each pair of degrees should meet the 270-19% GI6 regulations
4.4.3: The difference between the rated load and the rated load should be greater than
4.4.4 The broken parts of the machine should be tightly sealed to prevent leakage. 4.5.1 The return parts should not have severe vibration, and the upper double amplitude should not be greater than 0.5mm. 4.5.2 The upward temperature rise should not exceed 45%. The maximum reverse rotation of the shaft should not exceed 90: 4.5.3 The machine noise should be greater than 8.5 when operating under single load. (A!, Jn/T1O243-20C2
4.5.4 Crusher continuous operation time is not less than 2,! 1 After the bearing temperature reaches a stable 0.5h, the station will start the test run 4.6 Induction sleeve 9
4.6.1, the complete set of crusher supply scope includes: earth mover, mountain material car, T oil pump, pool foot butterfly inspection, etc. 46.2
Crushing in-situ technical documents should include: certificate of conformity, instruction manual, packing list, appearance foundation drawing, easy Required items: 5 Test method
The flexibility of the rotor parts shall be checked by the method of natural gas. There shall be no jamming phenomenon: 5.2
The rotor static flow test method shall comply with the provisions of GB/T9239-1988 5.3 The main shaft flow is tested by full acoustic wave: The method shall comply with the provisions of GB/T5000.15-1998. 5.4 The rolling bearing temperature is measured by inserting a piece of sample into the bearing. The test rate is once every 13 seconds until the temperature is stable. 5.5 Use a vibration meter to measure the double amplitude of the simplified body. 5.6 Use a sound level meter according to GBT3768199% two-dimensional measurement 5. The sealing test of the crusher joint is carried out by using a negative pressure machine with at least a number of white blocks and red blocks to crush the magnetic crusher. The joint must not leak 5. For test methods not specified in the technical requirements, the same pressure tool can be used for measurement, monthly measurement, new feeling, hand feeling and comparison. 6.9 The capacity can be converted into time when the continuous operation is carried out. That is, a period of time Within the time: the total amount of time is not less than 100.) All the broken materials are measured and converted into "hourly production capacity". 5.10 The discharge rate can be screened by the standard mesh flow group. 6 Inspection regulations
6.1 The product with a service life of more than 10 years must be inspected by the quality inspection department according to the factory inspection items before it can be shipped. Attach the product quality certificate. 6.2 Factory inspection: According to 4.1~4.3, 4.4.1~4.4.3.4.54.6, 7.17.4. 6.3 Type inspection
6.3.1 When one of the following conditions occurs, a type inspection shall be carried out. New products or old products are transferred to the factory for production
Product structure, material, and when there are major improvements, it may affect the product performance b
Long-term post-production calibration and production:
Statutory quality supervision and inspection machine launches type inspection 6.3.2. Inspection items: All parts required by the standards shall be inspected 7. Marking, packaging, transportation and storage
7.1 Product labels shall be made on the obvious parts of the products. Their type and size shall comply with the requirements of 13306-1991. The sequence on the label shall include
product model and name:
b) Semi-effectiveness:
! Manufacturer's name:
d) code;
e) output, H period
72 secretion machine before color installation fish side in addition to signs: water marks, all outer flag processing surface shall be coated with anti-rust grease, 3
J/F10343---2002
73 magnetic barrier 1 table to send a GBT13384
4 of the standard, each piece (shovel) and should have the following test mark certification product model
manufacturer's name:
! Factory number and container number:
d) Length x width x width:
c Net weight:
Shipping station: Port and receiving unit
Packaging, storage and transportation instructions shall comply with the provisions of CBT191-20C0 7.4
During the validity period of the crusher, it shall be regularly inspected to prevent rust. The electrical equipment shall be subject to necessary anti-rust measures. 7.5
9 Manufacturing guarantee
81 The manufacturer shall ensure that the product meets the requirements of the water standard. 8.2 Under the premise that the user complies with this standard and the instructions for use: within 12 to 6 months from the date of production or within this period from the date of use, if it cannot operate normally due to poor manufacturing quality, the factory shall not repair or replace parts, including easy certification
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.