HG/T 2081-2001 Cationic Brilliant Blue 2RL500% HG/T2081-2001 standard download decompression password: www.bzxz.net

Record number: 10107-2002
HG/T 2081-—2001
This standard is a revision of the recommended chemical industry standard HG/T2081-1991 "Cationic Brilliant Blue 2RL". The main differences between this standard and HG/T2081-1991 are: the specification of 250% as 100 points is cancelled, and 500% is stipulated as 100 points. Some indicators in the washing fastness and heat pressing color resistance are modified. The water insoluble content index is adjusted from less than or equal to 0.6% to less than or equal to 0.5%. From the date of implementation, this standard will replace HG/T2081-1991. This standard was proposed by the former State Petroleum and Chemical Industry Policy and Regulations Department, and this standard is under the jurisdiction of the National Dye Standardization Technical Committee. The drafting unit of this standard: Shenyang Chemical Research Institute. Zhangjiagang Gangda Dye Chemical Industry. The main drafters of this standard: Wang Yong, Ma Junqing, Lu Xiufeng. This standard was first issued in 1980 as the Ministry of Chemical Industry standard HG/T2-1387-80, and was first revised and adjusted to the chemical industry standard HG/T2081-1991 in 1991.
This standard is interpreted by the National Technical Committee for Dye Standardization. 1 Scope
Chemical Industry Standard of the People's Republic of China
Cationic Brilliant Blue 2RL
Cationic hrifliant bloe 2RL500%HG/T 2081--2001
Replaces HG/1 2081-1991wwW.bzxz.Net
This standard specifies the requirements, sampling, analysis steps, inspection rules, and marking, labeling, packaging, transportation and storage of cationic hrifliant blue 2RL (CI basic blue 54). This product is mainly used for dyeing acrylic fibers. Its compatibility index K=A. Structural formula:
Molecular formula: C,H ON,SZnCl.
Relative molecular mass: 199.18 (according to the 1997 international relative atomic mass) 2 Reference standards
The provisions contained in the following standards constitute the provisions of the standards through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised, and the parties using this standard should explore the feasibility of using the latest versions of the following standards. GB2374-1994 General conditions for dyeing determination GB/T2381-1994 Determination of non-woven fabric content in dyes GB/T2383-1980 Determination of sieving fineness of dyes Determination of moisture content in dyes and dye intermediates GB/T 2386-1980 GB/T 2399-1980 GB/T 2402-1980 GB/T 3920-1997 Determination of color intensity and strength of cationic dyes Determination of staining of other fabrics by cationic dyes on acrylic Textiles Tests for color fastness Color fastness to rubbing (cgVIS0) 105-X12 1993) GB/T 3921. 3.--1997
Textiles-Tests for color fastness to washing (eyvISO105C03:1989) GB/T3922-1995 Textiles-Tests for color fastness-Color fastness to perspiration (eqV1SO105-E04:1994) GR 4841.1-1984
G[3/T 6152-1997
G/T 6678.- 1986
1/1Dyeing standard depth color card
Textiles test for color fastness Color fastness to hot pressing (eqvIS0105-X11:1994) General rules for sampling of chemical products
GB/T8427—1998 Textiles test for color fastness Color fastness to artificial light Xenon arc shading (cV1SO)105-R02:1994)3 Requirements
3.1 Appearance: blue-black uniform powder.
3.2 The quality of Cationic Brilliant Blue 2RI. shall meet the requirements of Table 1. Approved by the State Economic and Trade Commission on January 24, 2002 and implemented on July 1, 2002
Color (with standard product)
Intensity (with standard product), points
Moisture content, %
Water insoluble matter content, %
HG/T2081—2001
Quality requirements for ionic brilliant blue 2RL
Fineness\ (the amount of residue passing through the standard sieve with an aperture of 250μm), %Note:
1) Fineness of products with dust-proof agent may not be assessed. It refers to
Approximately one micro
The pollution of cationic brilliant blue 2RL to other fabrics when dyeing acrylic should not be less than the requirements of Table 2. Table 2 Contamination of other fabrics by Cationic Brilliant Blue 2RL when dyeing acrylic Fabric
Color staining. Grade
The color fastness of Cationic Brilliant Blue 2RL on acrylic fabric shall not be lower than the provisions of Table 3. Viscose
Table 3 Color fastness of Cationic Brilliant Blue 2RI. on acrylic fabric Washing
Dyeing depth, % Light fastness (Xenon)
1) 0.15% (owf) is equivalent to 1/1 standard dyeing depth. 4 Sampling
Abrasion resistance
Hot pressing resistance
1s0℃
Discoloration, 4h
Sampling is done in batches, and the manufacturer takes the products mixed evenly at one time as one batch. The number of sampling barrels for each batch shall comply with the provisions of 6.6 in GB/T6678-1986. The packaging of the sample must be intact. When sampling, do not allow foreign impurities to fall into the product. Use a probe to sample from the upper, middle and lower parts of the barrel. The total amount of the sample must not be less than 200g. After the sample is fully mixed, it is divided into two clean, dry and well-sealed containers. Labels are attached to indicate the product name, manufacturer name, batch number, sampling period and location. One is for inspection and the other is kept for future reference.
5 Analysis steps
5.1 Determination of appearance
Use national measurement and evaluation.
5.2 Determination of dyeing color and intensity
-General conditions should comply with the relevant provisions of GB2374. The dyeing method adopts the dyeing method with dye inhibitor in GB/T2399--1980. 5.2.1 Preparation of dye bath
Dyeing depth is 0.25% (owf), 2g acrylic bulked yarn is used for dyeing, and the bath ratio is 1:100. Prepare dye baths in five 300 mL dye vats as specified in Table 4.
Dye vat number
0. 25 /1 000 mL.Standard solution
0. 25 g/1 000 ml.Sample solution
100 g/L anhydrous sodium sulfate solution
10 g/L.Acetic acid solution
10 g/L sodium acetate solution
t0 g/1.Retarder 1227 solution
Make up to total volume with distilled water
5.2.2 Dyeing operation
HG/T 2081: 2001
Table 4 Preparation of dye liquor
According to the provisions of the dyeing method with dye inhibitor in GB/T2399-1980 5.2.3 Evaluation of color light and intensity
According to the provisions of Chapter 6 of GB2374-1991. 5.3 Determination of moisture content
According to the provisions of Chapter 2 of the drying method in GB/T2386-1980. 5.4 Determination of water-insoluble matter content
According to the provisions of GB/T2381.
5.5 Determination of fineness
According to the provisions of GB/T2383. Use a standard sieve with an aperture of 250μm. 5.6 Determination of contamination of other fabrics when dyeing acrylic fiber is carried out in accordance with the provisions of GB/T2402.
5.7 Determination of color fastness on acrylic fabrics
All samples for color fastness determination are dyed to 1/1 standard depth according to GB 484 t. 1. The color fastness to rubbing is determined according to GI3/T 3920. The color fastness to washing is determined according to CB/T 3921.3. The color fastness to perspiration is determined according to GB/T 3922. The color fastness to heat is determined according to GB/T 6152, 150℃ press (4h). The color fastness to light is determined according to GB/T 8427. 6 Inspection rules
6.1 Inspection classification
In this standard, 3.1 and 3.2 are inspection items. 3.3 and 3.4 are regular inspection items, and they shall be inspected annually during continuous normal production.
6.2 Factory Inspection
Cationic Brilliant Blue 2RL shall be inspected by the quality inspection department of the dust production factory. The manufacturer shall ensure that all Cationic Brilliant Blue 2RI shipped out of the factory meet the requirements of this standard.
6.3 Re-test
If one of the indicators in the test results does not meet the requirements of this standard, samples should be taken from twice the amount of packaging for re-testing. Even if only one indicator in the re-test results does not meet the requirements of this standard, the entire batch of products cannot be accepted. 11
7 Marking, labeling, packaging, transportation and storage 7.1 Marking, labeling
HG/T2081—2001
Each packaging barrel of Cationic Brilliant Blue 2RI should be painted with a firm and clear mark, indicating the product name, specification, registered trademark, net content, manufacturer's name, factory address, standard number, batch number, and production date. The batch number and production date can also be printed on the label and placed outside the plastic bag in the packaging barrel together with the product quality inspection certificate. 7.2 Packaging
Cationic Brilliant Blue 2RL is packed in an iron barrel lined with a plastic bag and sealed and stamped. The net content of each package is 20kg. Other packaging can be negotiated and determined with the user.
7.3 Transportation
During transportation, it should be prevented from being inverted, handled with care, and collisions should be avoided. Do not damage the packaging. 7.4 Purchase and Storage
Cationic Brilliant Blue 2RL should be stored in a cool, dry, ventilated place to prevent moisture and heat. 12
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.